Skip to content
maunawai.info

Drinking water in Simmerath

12 supply zones — values can differ depending on the district. Below is the zone with the most documented parameters, the others collapsed underneath. To determine the exact match, look up the postcode.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
3.9 °dH
Hardness range 1
Key values Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS n.n. µg/L
not detectable
Mean
Nitrate 1,9 mg/L 50 mg/l
4 %
Single value · 18.11.2025
Lead <0,003 mg/L
below limit of quantification
10 µg/l
< 30 % *
Single value · 18.11.2025
Escherichia coli (E. coli) 0 MPN/100 mL 0/100 ml Maximum
Sulphate 6,2 mg/L 250 mg/l
2 %
Single value · 18.11.2025
Sodium 4,1 mg/L 200 mg/l
2 %
Single value · 18.11.2025

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (122 — most recent value per parameter)

Microbiology (3)

Microbiology – Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100 mL 0/100 ml Maximum
Intestinal enterococci 0 KBE/100 mL 0/100 ml Maximum
Somatic coliphages 0 PFU/100 mL 50/100 ml
UBA guide value
Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (69)

Chemical parameters – Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0007 mg/L
below limit of quantification
3 µg/l
< 23 % *
Single value · 18.11.2025
1,2-Dichloropropane < 0,08 µg/L
below limit of quantification
Single value · 18.11.2025
2,4-D < 0,02 µg/L
below limit of quantification
Single value · 18.11.2025
Acrylamide <0,00003 mg/L
below limit of quantification
0.1 µg/l
< 30 % *
Single value · 18.11.2025
Alachlor < 0,01 µg/L
below limit of quantification
Single value · 18.11.2025
Antimony <0,001 mg/L
below limit of quantification
5 µg/l
< 20 % *
Single value · 18.11.2025
Arsenic <0,001 mg/L
below limit of quantification
10 µg/l
< 10 % *
Single value · 18.11.2025
Atrazine < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Bentazone < 0,02 µg/L
below limit of quantification
Single value · 18.11.2025
Benzene <0,00005 mg/L
below limit of quantification
1 µg/l
< 5 % *
Single value · 18.11.2025
Benzo(a)pyrene <0,000002 mg/L
below limit of quantification
10 ng/l
< 20 % *
Single value · 18.11.2025
Benzo(b)fluoranthene <0,000005 mg/L
below limit of quantification
Single value · 18.11.2025
Benzo(ghi)perylene <0,000005 mg/L
below limit of quantification
Single value · 18.11.2025
Benzo(k)fluoranthene <0,000005 mg/L
below limit of quantification
Single value · 18.11.2025
Bisphenol A <0,000010 mg/L
below limit of quantification
2.5 µg/l
< 0.4 % *
Single value · 18.11.2025
Boron <0,01 mg/L
below limit of quantification
1 mg/l
< 1 % *
Single value · 18.11.2025
Bromacil < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Bromate <0,001 mg/L
below limit of quantification
10 µg/l
< 10 % *
Single value · 18.11.2025
Bromodichloromethane 0,0019 mg/L Single value · 18.11.2025
Cadmium <0,0003 mg/L
below limit of quantification
3 µg/l
< 10 % *
Single value · 18.11.2025
Carbofuran < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Chlorfenvinphos < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Chloridazon < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Chlorotoluron < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Chromium <0,0005 mg/L
below limit of quantification
25 µg/l
< 2 % *
Single value · 18.11.2025
Clopyralid < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Copper <0,005 mg/L
below limit of quantification
2 mg/l
< 0.3 % *
Single value · 18.11.2025
Cyanide <0,005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Single value · 18.11.2025
Dibromoacetic acid <0,001 mg/L
below limit of quantification
Mean
Dibromochloromethane 0,001 mg/L Single value · 18.11.2025
Dicamba < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Dichloroacetic acid <0,001 mg/L
below limit of quantification
Mean
Dichlorprop < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Diuron < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Epichlorohydrin <0,00003 mg/L
below limit of quantification
0.1 µg/l
< 30 % *
Single value · 18.11.2025
Fluoride 0,05 mg/L 1.5 mg/l
3 %
Single value · 18.11.2025
Haloacetic acids (HAA) n.n. mg/L
not detectable
Mean
Hexazinone < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Isoproturon < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Lead <0,003 mg/L
below limit of quantification
10 µg/l
< 30 % *
Single value · 18.11.2025
Lindane < 0,005 µg/L
below limit of quantification
Single value · 18.11.2025
MCPA < 0,02 µg/L
below limit of quantification
Single value · 18.11.2025
Mecoprop < 0,02 µg/L
below limit of quantification
Single value · 18.11.2025
Mercury <0,0001 mg/L
below limit of quantification
1 µg/l
< 10 % *
Single value · 18.11.2025
Metazachlor < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Methabenzthiazuron < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Metobromuron < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Metolachlor < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Metoxuron < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Microcystin-LR <0,00007 mg/L
below limit of quantification
Mean
Monobromoacetic acid <0,001 mg/L
below limit of quantification
Mean
Monochloroacetic acid <0,003 mg/L
below limit of quantification
Mean
Monuron < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Nickel <0,002 mg/L
below limit of quantification
20 µg/l
< 10 % *
Single value · 18.11.2025
Nitrate 1,9 mg/L 50 mg/l
4 %
Single value · 18.11.2025
Nitrite <0,05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean
Polycyclic aromatic hydrocarbons n.b. mg/L
not determined
0.1 µg/l Single value · 18.11.2025
Propazine < 0,02 µg/L
below limit of quantification
Single value · 18.11.2025
Selenium <0,003 mg/L
below limit of quantification
10 µg/l
< 30 % *
Single value · 18.11.2025
Simazine < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Terbuthylazine < 0,03 µg/L
below limit of quantification
Single value · 18.11.2025
Tetrachloroethene <0,0003 mg/L
below limit of quantification
Single value · 18.11.2025
Tribromomethane (bromoform) 0,0002 mg/L Single value · 18.11.2025
Trichloroacetic acid <0,001 mg/L
below limit of quantification
Mean
Trichloroethene <0,0003 mg/L
below limit of quantification
Single value · 18.11.2025
Trichloromethane (chloroform) 0,003 mg/L Single value · 18.11.2025
Trihalomethanes — Total 0,0061 mg/L 50 µg/l
12 %
Single value · 18.11.2025
Uranium <0,0001 mg/L
below limit of quantification
10 µg/l
< 1 % *
Single value · 18.11.2025
Vinyl chloride <0,00005 mg/L
below limit of quantification
0.5 µg/l
< 10 % *
Single value · 18.11.2025

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (21)

PFAS – Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
Perfluorobutane sulfonic acid (PFBS) <0,0010 µg/L
below limit of quantification
Mean
Perfluorobutanoic acid (PFBA) <0,0010 µg/L
below limit of quantification
Mean
Perfluorodecane sulfonic acid (PFDS) <0,0010 µg/L
below limit of quantification
Mean
Perfluorodecanoic acid (PFDA) <0,0010 µg/L
below limit of quantification
Mean
Perfluorododecane sulfonic acid (PFDoDS) <0,0010 µg/L
below limit of quantification
Mean
Perfluorododecanoic acid (PFDoDA) <0,0010 µg/L
below limit of quantification
Mean
Perfluoroheptane sulfonic acid (PFHpS) <0,0010 µg/L
below limit of quantification
Mean
Perfluoroheptanoic acid (PFHpA) <0,0010 µg/L
below limit of quantification
Mean
Perfluorohexane sulfonic acid (PFHxS) <0,0010 µg/L
below limit of quantification
Mean
Perfluorohexanoic acid (PFHxA) <0,0010 µg/L
below limit of quantification
Mean
Perfluorononane sulfonic acid (PFNS) <0,0010 µg/L
below limit of quantification
Mean
Perfluorononanoic acid (PFNA) <0,0010 µg/L
below limit of quantification
Mean
Perfluorooctanesulfonic acid (PFOS) <0,0010 µg/L
below limit of quantification
Mean
Perfluorooctanoic acid (PFOA) <0,0010 µg/L
below limit of quantification
Mean
Perfluoropentanesulfonic acid (PFPeS) <0,0010 µg/L
below limit of quantification
Mean
Perfluoropentanoic acid (PFPeA) <0,0010 µg/L
below limit of quantification
Mean
Perfluorotridecanesulfonic acid (PFTrDS) <0,0010 µg/L
below limit of quantification
Mean
Perfluorotridecanoic acid (PFTrDA) <0,0010 µg/L
below limit of quantification
Mean
Perfluoroundecanesulfonic acid (PFUnDS) <0,0010 µg/L
below limit of quantification
Mean
Perfluoroundecanoic acid (PFUnDA) <0,0010 µg/L
below limit of quantification
Mean
Sum of PFAS n.n. µg/L
not detectable
Mean

Indicator parameters (17)

Indicator parameters – Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,01 mg/L
below limit of quantification
0.2 mg/l
< 5 % *
Single value · 18.11.2025
Ammonium <0,02 mg/L
below limit of quantification
0.5 mg/l
< 4 % *
Single value · 18.11.2025
Chloride 22 mg/L 250 mg/l
9 %
Single value · 18.11.2025
Clostridium perfringens (including spores) 0 KBE/100 mL 0/100 ml Maximum
Coliform bacteria 0 MPN/100 mL 0/100 ml Maximum
Colony count 22 °C 0 KBE/mL ohne anormale Veränderung Single value · 18.11.2025
Colour <0,05 1/m
below limit of quantification
0.5 m⁻¹ Single value · 18.11.2025
Conductivity (25 °C) 164 µS/cm 2,790 µS/cm Single value · 18.11.2025
Iron <0,01 mg/L
below limit of quantification
0.2 mg/l
< 5 % *
Single value · 18.11.2025
Manganese <0,005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Single value · 18.11.2025
Odour ohne für den Verbraucher annehmbar Single value · 18.11.2025
pH 8,62 6,5–9,5 Single value · 18.11.2025
Sodium 4,1 mg/L 200 mg/l
2 %
Single value · 18.11.2025
Sulphate 6,2 mg/L 250 mg/l
2 %
Single value · 18.11.2025
Temperature 8,5 °C Mean
Total organic carbon (TOC) 0,58 mg/L ohne anormale Veränderung Single value · 18.11.2025
Turbidity <0,050 NTU
below limit of quantification
1 NTU Single value · 18.11.2025

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (2)

Radiology – Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
Indicative dose
not determined
Unit not stated in the document
0.1 mSv/a Single value
Radon-222 <10 Bq/L
below limit of quantification
100 Bq/l Single value · 17.12.2018

Treatment substances (2)

Treatment substances – Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
Free chlorine 0,21 mg/L Mean
Total chlorine 0,22 mg/L Mean

Further parameters (8)

Further parameters – Wasserwerksausgang
Parameter Value Parametric value Share of the parametric value Reference
Calcium 0,42 mmol/L Mean
Carbonate hardness 2,1 °dH Mean
Hardness range (WRMG) 1 Mean
Hydrogen carbonate 45,8 mg/L Mean
Magnesium 0,21 mmol/L Mean
Potassium 0,02 mmol/L Mean
Spectral absorption coefficient 254 nm (SAC 254) 1,0 1/m Mean
Total hardness 3,9 °dH Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserwerk-perlenbach.de/cms/module/2388/download/979/ · Jahr 2025 (Einzelanalyse vom 18.11.2025); Anlage 4.I: Jahr 2018, Analyse vom 17.12.2018 · retrieved on 19/08/2026

Postcodes in this zone: 52152

Show 11 more supply zones

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Arloff
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Arloff

Further parameters (1)

Further parameters – Arloff
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Arloff

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Bad Münstereifel

Stadt Bad Münstereifel

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Bad Münstereifel
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Bad Münstereifel

Further parameters (1)

Further parameters – Bad Münstereifel
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Bad Münstereifel

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
19 °dH
Hardness range hard

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Bergrath
Parameter Value Parametric value Share of the parametric value Reference
pH 7,8 6,5–9,5 Maximum · Bergrath

Further parameters (1)

Further parameters – Bergrath
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 19 °dH Maximum · Bergrath

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Berresheim
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Berresheim

Further parameters (1)

Further parameters – Berresheim
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Berresheim

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Effelsberg
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Effelsberg

Further parameters (1)

Further parameters – Effelsberg
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Effelsberg

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Eichen
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Eichen

Further parameters (1)

Further parameters – Eichen
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Eichen

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Eicherscheid
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Eicherscheid

Further parameters (1)

Further parameters – Eicherscheid
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Eicherscheid

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Ellesheim
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Ellesheim

Further parameters (1)

Further parameters – Ellesheim
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Ellesheim

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Esch
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Esch

Further parameters (1)

Further parameters – Esch
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Esch

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Escher Heide
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Escher Heide

Further parameters (1)

Further parameters – Escher Heide
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Escher Heide

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5 °dH
Hardness range soft

No core values are available for this zone yet.

Show all recorded parameters (2 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Eschweiler
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Maximum · Eschweiler

Further parameters (1)

Further parameters – Eschweiler
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5 °dH Maximum · Eschweiler

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 52152

Frequently asked questions about drinking water in Simmerath

How hard is the water in Simmerath?
Wasserversorgungszweckverband Perlenbach publishes a total hardness of 3.9 °dH for the supply zone Wasserwerksausgang (hardness range 1). The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 19/08/2026.
How much nitrate is in the drinking water in Simmerath?
Wasserversorgungszweckverband Perlenbach publishes a nitrate value of 1,9 mg/L for the supply zone Wasserwerksausgang. The statutory parametric value is 50 mg/l; the measured value represents 4 % of the parametric value. Basis: Publication by the water supplier, retrieved on 19/08/2026.
Who supplies the drinking water in Simmerath?
Wasserversorgungszweckverband Perlenbach. The values shown here come from the supply zone Wasserwerksausgang and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.