Skip to content
maunawai.info

Drinking water in Salzhemmendorf

2 supply zones — values can differ depending on the district. Below is the zone with the most documented parameters, the others collapsed underneath. To determine the exact match, look up the postcode.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
16.8 °dH
Hardness range hard
Key values Judenquelle
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 20 mg/l 50 mg/l
40 %
Single value · Judenquelle
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml Single value · Judenquelle
Sulphate 64 mg/l 250 mg/l
26 %
Single value · Judenquelle
Show all recorded parameters (56 — most recent value per parameter)

Microbiology (1)

Microbiology – Judenquelle
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml Single value · Judenquelle

Chemical parameters (30)

Chemical parameters – Judenquelle
Parameter Value Parametric value Share of the parametric value Reference
2,6-Dichlorobenzamide (BAM) <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
AMPA <0.00005 mg/l
below limit of quantification
Single value · Judenquelle
Atrazine <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Bentazone <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Bromacil <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Bromoxynil <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Chloridazon <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Chlorotoluron <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Desethylatrazine <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Desisopropylatrazine <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Dichlorprop-P <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Diflufenican <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Diuron <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Ethidimuron <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Ethofumesate <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Glyphosate <0.00005 mg/l
below limit of quantification
Single value · Judenquelle
Isoproturon <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
MCPA <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Mecoprop-P <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Metamitron <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Metazachlor <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Methabenzthiazuron <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Metolachlor <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Metoxuron <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Metribuzin <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Nitrate 20 mg/l 50 mg/l
40 %
Single value · Judenquelle
Nitrite <0.01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Judenquelle
Oxadixyl <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Simazine <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Terbuthylazine <0.00003 mg/l
below limit of quantification
Single value · Judenquelle

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Judenquelle
Parameter Value Parametric value Share of the parametric value Reference
Trifluoroacetic acid (TFA) <0.0005 mg/l
below limit of quantification
60 µg/l
UBA guide value
< 0.8 % *
Single value · Judenquelle

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Metabolites (7)

Metabolites – Judenquelle
Parameter Value Parametric value Share of the parametric value Reference
1H-1,2,4-Triazole <0.00008 mg/l
below limit of quantification
Single value · Judenquelle
Desphenyl-chloridazon <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Dimethachlor acid CGA 50266 <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Dimethachlor sulfonic acid CGA 354742 <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Metazachlor sulfonic acid BH 479-8 <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
Methyl-desphenyl-chloridazon <0.00003 mg/l
below limit of quantification
Single value · Judenquelle
S-metolachlor sulfonic acid CGA 380168/354743 <0.00003 mg/l
below limit of quantification
Single value · Judenquelle

Indicator parameters (10)

Indicator parameters – Judenquelle
Parameter Value Parametric value Share of the parametric value Reference
Ammonium <0.04 mg/l
below limit of quantification
0.5 mg/l
< 8 % *
Single value · Judenquelle
Chloride 13 mg/l 250 mg/l
5 %
Single value · Judenquelle
Coliform bacteria 0 MPN/100 ml 0/100 ml Single value · Judenquelle
Colony count 22 °C 6 KBE/ml ohne anormale Veränderung Single value · Judenquelle
Colour <0.100 1/m
below limit of quantification
0.5 m⁻¹ Single value · Judenquelle
Conductivity (25 °C) 587 µS/cm 2,790 µS/cm Single value · Judenquelle
Odour ohne für den Verbraucher annehmbar Single value · Judenquelle
Sulphate 64 mg/l 250 mg/l
26 %
Single value · Judenquelle
Temperature 10.6 °C Single value · Judenquelle
Turbidity ohne
Unit not stated in the document
1 NTU Single value · Judenquelle

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Judenquelle
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 4.6 mmol/l Single value · Judenquelle
AOX (adsorbable organically bound halogens) <0.01 mg/l
below limit of quantification
Single value · Judenquelle
Base capacity to pH 8.2 <0.2 mmol/l
below limit of quantification
Single value · Judenquelle
Dissolved organic carbon (DOC) <1 mg/l
below limit of quantification
Single value · Judenquelle
Oxygen 8.37 mg/l Single value · Judenquelle
Phosphate 0.09 mg/l PO4 Single value · Judenquelle
Total hardness 3.0 mmol/l Single value · Judenquelle

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.salzhemmendorf.de/wp-content/uploads/wasser/Wasseranalysen_Salzhemmendorf.pdf · 08.11.23 · Prüfdauer 21.09.23 - 08.11.23 · retrieved on 13/07/2026

Postcodes in this zone: 31020

Show 1 more supply zone

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
17.4 °dH
Hardness range hard
Key values Steinerquelle
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 20 mg/l 50 mg/l
40 %
Single value · Steinerquelle
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml Single value · Steinerquelle
Sulphate 64 mg/l 250 mg/l
26 %
Single value · Steinerquelle
Show all recorded parameters (56 — most recent value per parameter)

Microbiology (1)

Microbiology – Steinerquelle
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml Single value · Steinerquelle

Chemical parameters (30)

Chemical parameters – Steinerquelle
Parameter Value Parametric value Share of the parametric value Reference
2,6-Dichlorobenzamide (BAM) <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
AMPA <0.00005 mg/l
below limit of quantification
Single value · Steinerquelle
Atrazine <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Bentazone <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Bromacil <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Bromoxynil <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Chloridazon <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Chlorotoluron <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Desethylatrazine <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Desisopropylatrazine <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Dichlorprop-P <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Diflufenican <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Diuron <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Ethidimuron <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Ethofumesate <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Glyphosate <0.00005 mg/l
below limit of quantification
Single value · Steinerquelle
Isoproturon <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
MCPA <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Mecoprop-P <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Metamitron <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Metazachlor <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Methabenzthiazuron <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Metolachlor <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Metoxuron <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Metribuzin <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Nitrate 20 mg/l 50 mg/l
40 %
Single value · Steinerquelle
Nitrite <0.01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Steinerquelle
Oxadixyl <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Simazine <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Terbuthylazine <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Steinerquelle
Parameter Value Parametric value Share of the parametric value Reference
Trifluoroacetic acid (TFA) <0.0005 mg/l
below limit of quantification
60 µg/l
UBA guide value
< 0.8 % *
Single value · Steinerquelle

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Metabolites (7)

Metabolites – Steinerquelle
Parameter Value Parametric value Share of the parametric value Reference
1H-1,2,4-Triazole <0.00008 mg/l
below limit of quantification
Single value · Steinerquelle
Desphenyl-chloridazon <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Dimethachlor acid CGA 50266 <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Dimethachlor sulfonic acid CGA 354742 <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Metazachlor sulfonic acid BH 479-8 <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
Methyl-desphenyl-chloridazon <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle
S-metolachlor sulfonic acid CGA 380168/354743 <0.00003 mg/l
below limit of quantification
Single value · Steinerquelle

Indicator parameters (10)

Indicator parameters – Steinerquelle
Parameter Value Parametric value Share of the parametric value Reference
Ammonium <0.04 mg/l
below limit of quantification
0.5 mg/l
< 8 % *
Single value · Steinerquelle
Chloride 16 mg/l 250 mg/l
6 %
Single value · Steinerquelle
Coliform bacteria 0 MPN/100 ml 0/100 ml Single value · Steinerquelle
Colony count 22 °C 2 KBE/ml ohne anormale Veränderung Single value · Steinerquelle
Colour <0.100 1/m
below limit of quantification
0.5 m⁻¹ Single value · Steinerquelle
Conductivity (25 °C) 607 µS/cm 2,790 µS/cm Single value · Steinerquelle
Odour ohne für den Verbraucher annehmbar Single value · Steinerquelle
Sulphate 64 mg/l 250 mg/l
26 %
Single value · Steinerquelle
Temperature 10.5 °C Single value · Steinerquelle
Turbidity ohne
Unit not stated in the document
1 NTU Single value · Steinerquelle

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Steinerquelle
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 4.7 mmol/l Single value · Steinerquelle
AOX (adsorbable organically bound halogens) <0.01 mg/l
below limit of quantification
Single value · Steinerquelle
Base capacity to pH 8.2 <0.2 mmol/l
below limit of quantification
Single value · Steinerquelle
Dissolved organic carbon (DOC) <1 mg/l
below limit of quantification
Single value · Steinerquelle
Oxygen 7.54 mg/l Single value · Steinerquelle
Phosphate 0.07 mg/l PO4 Single value · Steinerquelle
Total hardness 3.1 mmol/l Single value · Steinerquelle

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.salzhemmendorf.de/wp-content/uploads/wasser/Wasseranalysen_Salzhemmendorf.pdf · 08.11.23 · Prüfdauer 21.09.23 - 08.11.23 · retrieved on 13/07/2026

Postcodes in this zone: 31020

Frequently asked questions about drinking water in Salzhemmendorf

How hard is the water in Salzhemmendorf?
Westfalen Weser Netz AG publishes a total hardness of 3.0 mmol/l for the supply zone Judenquelle — that corresponds to 16.8 °dH. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: 08.11.23, retrieved on 13/07/2026.
How much nitrate is in the drinking water in Salzhemmendorf?
Westfalen Weser Netz AG publishes a nitrate value of 20 mg/l for the supply zone Judenquelle. The statutory parametric value is 50 mg/l; the measured value represents 40 % of the parametric value. Basis: 08.11.23, retrieved on 13/07/2026.
Who supplies the drinking water in Salzhemmendorf?
Westfalen Weser Netz AG. The values shown here come from the supply zone Judenquelle and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.