How hard is the water in Klötze, Apenburg-Winterfeld?

Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel publishes a total hardness of 9.3 °dH for the supply zone Diesdorf (hardness range mittel). The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: 15.06.2026, retrieved on 11/07/2026.

How much nitrate is in the drinking water in Klötze, Apenburg-Winterfeld?

Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel publishes a nitrate value of <1,0 mg/l for the supply zone Diesdorf. The statutory parametric value is 50 mg/l; the measured value lies below it and cannot be specified more precisely below the limit of quantification. Basis: 15.06.2026, retrieved on 11/07/2026.

Who supplies the drinking water in Klötze, Apenburg-Winterfeld?

Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel. The values shown here come from the supply zone Diesdorf and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

Drinking water in Klötze, Apenburg-Winterfeld

7 supply zones — values can differ depending on the district. Below is the zone with the most documented parameters, the others collapsed underneath. To determine the exact match, look up the postcode.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.

< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Diesdorf

Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness

9.3 °dH

Hardness range mittel

Key values Diesdorf
Parameter	Value	Parametric value	Share of the parametric value	Reference
Nitrate	<1,0 mg/l below limit of quantification	50 mg/l	< 2 % *	Mean
Lead	< 0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Escherichia coli (E. coli)	0 KBE/100 ml	0/100 ml	—	Mean
Sulphate	59 mg/l	250 mg/l	24 %	Mean
Sodium	10,7 mg/l	200 mg/l	5 %	Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (45 — most recent value per parameter)

Microbiology (2)

Microbiology – Diesdorf
Parameter	Value	Parametric value	Share of the parametric value	Reference
Escherichia coli (E. coli)	0 KBE/100 ml	0/100 ml	—	Mean
Intestinal enterococci	0 KBE/100 ml	0/100 ml	—	Mean

Chemical parameters (21)

Chemical parameters – Diesdorf
Parameter	Value	Parametric value	Share of the parametric value	Reference
1,2-dichloroethane	<0,00050 mg/l below limit of quantification	3 µg/l	< 17 % *	Mean
Antimony	< 0,0010 mg/l below limit of quantification	5 µg/l	< 20 % *	Mean
Arsenic	< 0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Benzene	<0,00030 mg/l below limit of quantification	1 µg/l	< 30 % *	Mean
Benzo(a)pyrene	<0,0000025 mg/l below limit of quantification	10 ng/l	< 25 % *	Mean
Bisphenol A	<0,00010 mg/l below limit of quantification	2.5 µg/l	< 4 % *	Mean
Boron	< 0,100 mg/l below limit of quantification	1 mg/l	< 10 % *	Mean
Cadmium	< 0,0003 mg/l below limit of quantification	3 µg/l	< 10 % *	Mean
Chromium	< 0,000050 mg/l below limit of quantification	25 µg/l	< 0.2 % *	Mean
Copper	< 0,0020 mg/l below limit of quantification	2 mg/l	< 0.1 % *	Mean
Cyanide	< 0,010 mg/l below limit of quantification	50 µg/l	< 20 % *	Mean
Fluoride	< 0,20 mg/l below limit of quantification	1.5 mg/l	< 13 % *	Mean
Lead	< 0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Mercury	< 0,0001 mg/l below limit of quantification	1 µg/l	< 10 % *	Mean
Nickel	< 0,0020 mg/l below limit of quantification	20 µg/l	< 10 % *	Mean
Nitrate	<1,0 mg/l below limit of quantification	50 mg/l	< 2 % *	Mean
Nitrite	<0,010 mg/l below limit of quantification	0.5 mg/l	< 2 % *	Mean
Polycyclic aromatic hydrocarbons	<0,000025 mg/l below limit of quantification	0.1 µg/l	< 25 % *	Mean
Selenium	< 0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Uranium	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Vinyl chloride	<0,00015 mg/l below limit of quantification	0.5 µg/l	< 30 % *	Mean

Indicator parameters (14)

Indicator parameters – Diesdorf
Parameter	Value	Parametric value	Share of the parametric value	Reference
Aluminium	< 0,020 mg/l below limit of quantification	0.2 mg/l	< 10 % *	Mean
Ammonium	< 0,01 mg/l below limit of quantification	0.5 mg/l	< 2 % *	Mean
Calcite dissolution capacity	-0,02 mmol/l CaCO3	5 mg/l CaCO3	—	Mean
Chloride	23,0 mg/l	250 mg/l	9 %	Mean
Coliform bacteria	0 KBE/100 ml	0/100 ml	—	Mean
Colony count 22 °C	0 KBE/ml	ohne anormale Veränderung	—	Mean
Colony count 36 °C	0 KBE/ml	ohne anormale Veränderung	—	Mean
Iron	<0,010 mg/l below limit of quantification	0.2 mg/l	< 5 % *	Mean
Manganese	<0,002 mg/l below limit of quantification	50 µg/l	< 4 % *	Mean
Oxidisability	0,7 mg/l O2	5 mg/l O2	—	Mean
Sodium	10,7 mg/l	200 mg/l	5 %	Mean
Sulphate	59 mg/l	250 mg/l	24 %	Mean
Total organic carbon (TOC)	1,04 mg/l C	ohne anormale Veränderung	—	Mean
Turbidity	0,30 NTU	1 NTU	—	Mean

Further parameters (8)

Further parameters – Diesdorf
Parameter	Value	Parametric value	Share of the parametric value	Reference
Acid capacity to pH 4.3	1,91 mmol/l	—	—	Mean
Base capacity to pH 8.2	0,03 mmol/l	—	—	Mean
Calcium	59,7 mg/l	—	—	Mean
Hardness range (WRMG)	mittel weich/mittel/hart	—	—	Mean
Magnesium	4,1 mg/l	—	—	Mean
Potassium	1,0 mg/l	—	—	Mean
Silicate / silicic acid	14,3 mg/l	—	—	Mean
Total hardness	9,3 °dH	—	—	Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.vkwa-salzwedel.de/upload/Trinkwasseranalyse_2025_WW_Diesdorf.pdf · 15.06.2026 · Jahresmittelwert 2025 · retrieved on 11/07/2026

Postcodes in this zone: 38486

Show 6 more supply zones

Nipkendey

Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness

9.6 °dH

Hardness range mittel

Key values Nipkendey
Parameter	Value	Parametric value	Share of the parametric value	Reference
Nitrate	<1,0 mg/l below limit of quantification	50 mg/l	< 2 % *	Mean
Lead	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Escherichia coli (E. coli)	0 KBE/100 ml	0/100 ml	—	Mean
Sulphate	48 mg/l	250 mg/l	19 %	Mean
Sodium	14,2 mg/l	200 mg/l	7 %	Mean

Show all recorded parameters (41 — most recent value per parameter)

Microbiology (2)

Microbiology – Nipkendey
Parameter	Value	Parametric value	Share of the parametric value	Reference
Escherichia coli (E. coli)	0 KBE/100 ml	0/100 ml	—	Mean
Intestinal enterococci	0 KBE/100 ml	0/100 ml	—	Mean

Chemical parameters (19)

Chemical parameters – Nipkendey
Parameter	Value	Parametric value	Share of the parametric value	Reference
1,2-dichloroethane	<0,00050 mg/l below limit of quantification	3 µg/l	< 17 % *	Mean
Antimony	<0,0010 mg/l below limit of quantification	5 µg/l	< 20 % *	Mean
Arsenic	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Benzene	<0,00030 mg/l below limit of quantification	1 µg/l	< 30 % *	Mean
Benzo(a)pyrene	<0,0000025 mg/l below limit of quantification	10 ng/l	< 25 % *	Mean
Boron	<0,100 mg/l below limit of quantification	1 mg/l	< 10 % *	Mean
Cadmium	<0,0003 mg/l below limit of quantification	3 µg/l	< 10 % *	Mean
Chromium	<0,000050 mg/l below limit of quantification	25 µg/l	< 0.2 % *	Mean
Copper	<0,0020 mg/l below limit of quantification	2 mg/l	< 0.1 % *	Mean
Cyanide	<0,010 mg/l below limit of quantification	50 µg/l	< 20 % *	Mean
Fluoride	<0,20 mg/l below limit of quantification	1.5 mg/l	< 13 % *	Mean
Lead	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Mercury	<0,0001 mg/l below limit of quantification	1 µg/l	< 10 % *	Mean
Nickel	<0,0020 mg/l below limit of quantification	20 µg/l	< 10 % *	Mean
Nitrate	<1,0 mg/l below limit of quantification	50 mg/l	< 2 % *	Mean
Nitrite	0,01 mg/l	0.5 mg/l	2 %	Mean
Polycyclic aromatic hydrocarbons	<0,000025 mg/l below limit of quantification	0.1 µg/l	< 25 % *	Mean
Selenium	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Uranium	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean

Indicator parameters (12)

Indicator parameters – Nipkendey
Parameter	Value	Parametric value	Share of the parametric value	Reference
Aluminium	< 0,020 mg/l below limit of quantification	0.2 mg/l	< 10 % *	Mean
Ammonium	< 0,01 mg/l below limit of quantification	0.5 mg/l	< 2 % *	Mean
Chloride	16,0 mg/l	250 mg/l	6 %	Mean
Coliform bacteria	0 KBE/100 ml	0/100 ml	—	Mean
Colony count 22 °C	0 KBE/ml	ohne anormale Veränderung	—	Mean
Colony count 36 °C	0 KBE/ml	ohne anormale Veränderung	—	Mean
Iron	<0,010 mg/l below limit of quantification	0.2 mg/l	< 5 % *	Mean
Manganese	<0,002 mg/l below limit of quantification	50 µg/l	< 4 % *	Mean
Sodium	14,2 mg/l	200 mg/l	7 %	Mean
Sulphate	48 mg/l	250 mg/l	19 %	Mean
Total organic carbon (TOC)	1,15 mg/l C	ohne anormale Veränderung	—	Mean
Turbidity	0,2 NTU	1 NTU	—	Mean

Further parameters (8)

Further parameters – Nipkendey
Parameter	Value	Parametric value	Share of the parametric value	Reference
Acid capacity to pH 4.3	2,54 mmol/l	—	—	Mean
Base capacity to pH 8.2	0,12 mmol/l	—	—	Mean
Calcium	62,2 mg/l	—	—	Mean
Hardness range (WRMG)	mittel weich/mittel/hart	—	—	Mean
Magnesium	3,7 mg/l	—	—	Mean
Potassium	1,1 mg/l	—	—	Mean
Silicate / silicic acid	14,4 mg/l	—	—	Mean
Total hardness	9,6 °dH	—	—	Mean

Source: https://www.vkwa-salzwedel.de/upload/Trinkwasseranalyse_2025_WW_Nipkendey.pdf · 15.06.2026 · Jahresmittelwert 2025 · retrieved on 11/07/2026

Postcodes in this zone: 38486

Siedenlangenbeck

Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness

7.7 °dH

Hardness range weich

Key values Siedenlangenbeck
Parameter	Value	Parametric value	Share of the parametric value	Reference
Nitrate	<1,0 mg/l below limit of quantification	50 mg/l	< 2 % *	Mean
Lead	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Escherichia coli (E. coli)	0 KBE/ 100 ml	0/100 ml	—	Mean
Sulphate	27 mg/l	250 mg/l	11 %	Mean
Sodium	8,0 mg/l	200 mg/l	4 %	Mean

Show all recorded parameters (45 — most recent value per parameter)

Microbiology (2)

Microbiology – Siedenlangenbeck
Parameter	Value	Parametric value	Share of the parametric value	Reference
Escherichia coli (E. coli)	0 KBE/ 100 ml	0/100 ml	—	Mean
Intestinal enterococci	0 KBE/ 100 ml	0/100 ml	—	Mean

Chemical parameters (21)

Chemical parameters – Siedenlangenbeck
Parameter	Value	Parametric value	Share of the parametric value	Reference
1,2-dichloroethane	<0,00050 mg/l below limit of quantification	3 µg/l	< 17 % *	Mean
Antimony	<0,0010 mg/l below limit of quantification	5 µg/l	< 20 % *	Mean
Arsenic	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Benzene	<0,00030 mg/l below limit of quantification	1 µg/l	< 30 % *	Mean
Benzo(a)pyrene	<0,0000025 mg/l below limit of quantification	10 ng/l	< 25 % *	Mean
Bisphenol A	0,0025 mg/l	2.5 µg/l	100 %	Mean
Boron	<0,100 mg/l below limit of quantification	1 mg/l	< 10 % *	Mean
Cadmium	<0,0003 mg/l below limit of quantification	3 µg/l	< 10 % *	Mean
Chromium	<0,000062 mg/l below limit of quantification	25 µg/l	< 0.2 % *	Mean
Copper	0,0037 mg/l	2 mg/l	0.2 %	Mean
Cyanide	<0,010 mg/l below limit of quantification	50 µg/l	< 20 % *	Mean
Fluoride	<0,20 mg/l below limit of quantification	1.5 mg/l	< 13 % *	Mean
Lead	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Mercury	<0,0001 mg/l below limit of quantification	1 µg/l	< 10 % *	Mean
Nickel	<0,0020 mg/l below limit of quantification	20 µg/l	< 10 % *	Mean
Nitrate	<1,0 mg/l below limit of quantification	50 mg/l	< 2 % *	Mean
Nitrite	<0,010 mg/l below limit of quantification	0.5 mg/l	< 2 % *	Mean
Polycyclic aromatic hydrocarbons	n.q. mg/l not detectable	0.1 µg/l	—	Mean
Selenium	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Uranium	<0,001 mg/l below limit of quantification	10 µg/l	< 10 % *	Mean
Vinyl chloride	0,0005 mg/l	0.5 µg/l	100 %	Mean

Indicator parameters (14)

Indicator parameters – Siedenlangenbeck
Parameter	Value	Parametric value	Share of the parametric value	Reference
Aluminium	< 0,020 mg/l below limit of quantification	0.2 mg/l	< 10 % *	Mean
Ammonium	<0,01 mg/l below limit of quantification	0.5 mg/l	< 2 % *	Mean
Calcite dissolution capacity	-0,04 mmol/l CaCO3	5 mg/l CaCO3	—	Mean
Chloride	15,0 mg/l	250 mg/l	6 %	Mean
Coliform bacteria	0 KBE /100 ml	0/100 ml	—	Mean
Colony count 22 °C	0 KBE/ml	ohne anormale Veränderung	—	Mean
Colony count 36 °C	0 KBE/ml	ohne anormale Veränderung	—	Mean
Iron	<0,011 mg/l below limit of quantification	0.2 mg/l	< 5 % *	Mean
Manganese	<0,002 mg/l below limit of quantification	50 µg/l	< 4 % *	Mean
Oxidisability	0,9 mg/l O2	5 mg/l O2	—	Mean
Sodium	8,0 mg/l	200 mg/l	4 %	Mean
Sulphate	27 mg/l	250 mg/l	11 %	Mean
Total organic carbon (TOC)	0,99 mg/l C	ohne anormale Veränderung	—	Mean
Turbidity	0,29 NTU	1 NTU	—	Mean

Further parameters (8)

Further parameters – Siedenlangenbeck
Parameter	Value	Parametric value	Share of the parametric value	Reference
Acid capacity to pH 4.3	2,15 mmol/l	—	—	Mean
Base capacity to pH 8.2	0,02 mmol/l	—	—	Mean
Calcium	50,8 mg/l	—	—	Mean
Hardness range (WRMG)	weich weich/mittel/hart	—	—	Mean
Magnesium	2,7 mg/l	—	—	Mean
Potassium	0,9 mg/l	—	—	Mean
Silicate / silicic acid	15,34 mg/l	—	—	Mean
Total hardness	7,7 °dH	—	—	Mean

Source: https://www.vkwa-salzwedel.de/upload/Trinkwasseranalyse_2025_WW_Siebeck.pdf · 15.06.2026 · Jahresmittelwert 2025 · retrieved on 11/07/2026

Postcodes in this zone: 38486

WVG WW Klötze

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2023. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Key values WVG WW Klötze
Parameter	Value	Parametric value	Share of the parametric value	Reference
Nitrate	2,29 mg/l	50 mg/l	5 %	Mean · WVG WW Klötze
Sulphate	97,665 mg/l	250 mg/l	39 %	Mean · WVG WW Klötze
Sodium	15,33 mg/l	200 mg/l	8 %	Mean · WVG WW Klötze

Show all recorded parameters (7 — most recent value per parameter)

Chemical parameters (1)

Chemical parameters – WVG WW Klötze
Parameter	Value	Parametric value	Share of the parametric value	Reference
Nitrate	2,29 mg/l	50 mg/l	5 %	Mean · WVG WW Klötze

Indicator parameters (6)

Indicator parameters – WVG WW Klötze
Parameter	Value	Parametric value	Share of the parametric value	Reference
Ammonium	0,01 mg/l	0.5 mg/l	2 %	Mean · WVG WW Klötze
Chloride	32,795 mg/l	250 mg/l	13 %	Mean · WVG WW Klötze
Iron	0,0562 mg/l	0.2 mg/l	28 %	Mean · WVG WW Klötze
Manganese	0,011 mg/l	50 µg/l	22 %	Mean · WVG WW Klötze
Sodium	15,33 mg/l	200 mg/l	8 %	Mean · WVG WW Klötze
Sulphate	97,665 mg/l	250 mg/l	39 %	Mean · WVG WW Klötze

Source: https://lavst.azurewebsites.net/wasserkarte/gemeinden/15081045a.pdf · Jahresmittel 2023 · Jahresmittel 2023 · retrieved on 18/08/2026

Postcodes in this zone: 38486

WVG WW Kusey

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values WVG WW Kusey
Parameter	Value	Parametric value	Share of the parametric value	Reference
Sulphate	176,23333 mg/l	250 mg/l	70 %	Mean · WVG WW Kusey
Sodium	24,5 mg/l	200 mg/l	12 %	Mean · WVG WW Kusey

Show all recorded parameters (6 — most recent value per parameter)

Chemical parameters (1)

Chemical parameters – WVG WW Kusey
Parameter	Value	Parametric value	Share of the parametric value	Reference
Chromium	0,0001 mg/l	25 µg/l	0.4 %	Mean · WVG WW Kusey

Indicator parameters (5)

Indicator parameters – WVG WW Kusey
Parameter	Value	Parametric value	Share of the parametric value	Reference
Ammonium	0,08 mg/l	0.5 mg/l	16 %	Mean · WVG WW Kusey
Chloride	55,313333 mg/l	250 mg/l	22 %	Mean · WVG WW Kusey
Iron	0,021 mg/l	0.2 mg/l	11 %	Mean · WVG WW Kusey
Sodium	24,5 mg/l	200 mg/l	12 %	Mean · WVG WW Kusey
Sulphate	176,23333 mg/l	250 mg/l	70 %	Mean · WVG WW Kusey

Source: https://lavst.azurewebsites.net/wasserkarte/gemeinden/15081280d.pdf · Jahresmittel 2023 · Jahresmittel 2023 · retrieved on 18/08/2026

Postcodes in this zone: 38486

WVG WW Solpke

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values WVG WW Solpke
Parameter	Value	Parametric value	Share of the parametric value	Reference
Nitrate	1,05 mg/l	50 mg/l	2 %	Mean · WVG WW Solpke
Sulphate	41,61667 mg/l	250 mg/l	17 %	Mean · WVG WW Solpke
Sodium	7,41 mg/l	200 mg/l	4 %	Mean · WVG WW Solpke

Show all recorded parameters (8 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – WVG WW Solpke
Parameter	Value	Parametric value	Share of the parametric value	Reference
Arsenic	0,001515 mg/l	10 µg/l	15 %	Mean · WVG WW Solpke
Chromium	0,0001 mg/l	25 µg/l	0.4 %	Mean · WVG WW Solpke
Nitrate	1,05 mg/l	50 mg/l	2 %	Mean · WVG WW Solpke

Indicator parameters (5)

Indicator parameters – WVG WW Solpke
Parameter	Value	Parametric value	Share of the parametric value	Reference
Ammonium	0,01 mg/l	0.5 mg/l	2 %	Mean · WVG WW Solpke
Chloride	9,136667 mg/l	250 mg/l	4 %	Mean · WVG WW Solpke
Iron	0,0153 mg/l	0.2 mg/l	8 %	Mean · WVG WW Solpke
Sodium	7,41 mg/l	200 mg/l	4 %	Mean · WVG WW Solpke
Sulphate	41,61667 mg/l	250 mg/l	17 %	Mean · WVG WW Solpke

Source: https://lavst.azurewebsites.net/wasserkarte/gemeinden/15081135c.pdf · Jahresmittel 2023 · Jahresmittel 2023 · retrieved on 18/08/2026

Postcodes in this zone: 38486

WVG WW Wiepke

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values WVG WW Wiepke
Parameter	Value	Parametric value	Share of the parametric value	Reference
Sulphate	51,745 mg/l	250 mg/l	21 %	Mean · WVG WW Wiepke
Sodium	11,76 mg/l	200 mg/l	6 %	Mean · WVG WW Wiepke

Show all recorded parameters (6 — most recent value per parameter)

Chemical parameters (1)

Chemical parameters – WVG WW Wiepke
Parameter	Value	Parametric value	Share of the parametric value	Reference
Uranium	0,00204 mg/l	10 µg/l	20 %	Mean · WVG WW Wiepke

Indicator parameters (5)

Indicator parameters – WVG WW Wiepke
Parameter	Value	Parametric value	Share of the parametric value	Reference
Ammonium	0,01 mg/l	0.5 mg/l	2 %	Mean · WVG WW Wiepke
Chloride	20,93 mg/l	250 mg/l	8 %	Mean · WVG WW Wiepke
Iron	0,024 mg/l	0.2 mg/l	12 %	Mean · WVG WW Wiepke
Sodium	11,76 mg/l	200 mg/l	6 %	Mean · WVG WW Wiepke
Sulphate	51,745 mg/l	250 mg/l	21 %	Mean · WVG WW Wiepke

Source: https://lavst.azurewebsites.net/wasserkarte/gemeinden/15081135b.pdf · Jahresmittel 2023 · Jahresmittel 2023 · retrieved on 18/08/2026

Postcodes in this zone: 38486

Frequently asked questions about drinking water in Klötze, Apenburg-Winterfeld

How hard is the water in Klötze, Apenburg-Winterfeld?: Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel publishes a total hardness of 9.3 °dH for the supply zone Diesdorf (hardness range mittel). The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: 15.06.2026, retrieved on 11/07/2026.
How much nitrate is in the drinking water in Klötze, Apenburg-Winterfeld?: Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel publishes a nitrate value of <1,0 mg/l for the supply zone Diesdorf. The statutory parametric value is 50 mg/l; the measured value lies below it and cannot be specified more precisely below the limit of quantification. Basis: 15.06.2026, retrieved on 11/07/2026.
Who supplies the drinking water in Klötze, Apenburg-Winterfeld?: Verband Kommunaler Wasserversorgung und Abwasserbehandlung (VKWA) Salzwedel. The values shown here come from the supply zone Diesdorf and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.