Skip to content
maunawai.info

Drinking water in Bergen

There are 4 places with this name — listed below by area. To determine the exact match, look up the postcode.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Bergen (08239)

Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße

ZWAV (Zweckverband Wasserversorgung und Abwasserentsorgung Vogtland)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
14.7 °dH
Hardness range hard
Key values Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 5,3 mg/l 50 mg/l
11 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Sulphate 95 mg/l 250 mg/l
38 %
Single value
Sodium 11,8 mg/l 200 mg/l
6 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (115 — most recent value per parameter)

Microbiology (2)

Microbiology – Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Intestinal enterococci 0 Anzahl/100ml 0/100 ml Single value

Chemical parameters (84)

Chemical parameters – Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00090 mg/l
below limit of quantification
3 µg/l
< 30 % *
Single value
2,4-D <0,000020 mg/l
below limit of quantification
Single value
Antimony 0,0017 mg/l 5 µg/l
34 %
Single value
Arsenic <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Atrazine <0,000020 mg/l
below limit of quantification
Single value
Azoxystrobin <0,000020 mg/l
below limit of quantification
Single value
Bentazone <0,000020 mg/l
below limit of quantification
Single value
Benzene <0,00050 mg/l
below limit of quantification
1 µg/l
< 50 % *
Single value
Benzo(a)pyrene <0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Benzo(b)fluoranthene <0,00001 mg/l
below limit of quantification
Single value
Benzo(ghi)perylene <0,00001 mg/l
below limit of quantification
Single value
Benzo(k)fluoranthene <0,00001 mg/l
below limit of quantification
Single value
Boron 0,015 mg/l 1 mg/l
2 %
Single value
Boscalid <0,000020 mg/l
below limit of quantification
Single value
Bromacil <0,000020 mg/l
below limit of quantification
Single value
Bromate <0,0025 mg/l
below limit of quantification
10 µg/l
< 25 % *
Single value
Bromodichloromethane <0,00030 mg/l
below limit of quantification
Single value
Bromoxynil <0,000020 mg/l
below limit of quantification
Single value
Cadmium <0,0001 mg/l
below limit of quantification
3 µg/l
< 3 % *
Single value
Carbendazim <0,000020 mg/l
below limit of quantification
Single value
Chlorate <0,010 mg/l
below limit of quantification
70 µg/l
< 14 % *
Single value
Chloridazon <0,000020 mg/l
below limit of quantification
Single value
Chlorotoluron <0,000020 mg/l
below limit of quantification
Single value
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper 0,0026 mg/l 2 mg/l
0.1 %
Single value
Cyanazine <0,000020 mg/l
below limit of quantification
Single value
Cyanide <0,01 mg/l
below limit of quantification
50 µg/l
< 20 % *
Single value
Desethylatrazine <0,000020 mg/l
below limit of quantification
Single value
Desisopropylatrazine <0,000020 mg/l
below limit of quantification
Single value
Dibromoacetic acid <0,0030 mg/l
below limit of quantification
Single value
Dibromochloromethane <0,00030 mg/l
below limit of quantification
Single value
Dichloroacetic acid <0,0030 mg/l
below limit of quantification
Single value
Dichlorprop <0,000020 mg/l
below limit of quantification
Single value
Diflufenican <0,000020 mg/l
below limit of quantification
Single value
Dimefuron <0,000020 mg/l
below limit of quantification
Single value
Dimethachlor <0,000020 mg/l
below limit of quantification
Single value
Dimethachlor sulfonic acid <0,000020 mg/l
below limit of quantification
Single value
Dimethenamid <0,000020 mg/l
below limit of quantification
Single value
Dimethoate <0,000020 mg/l
below limit of quantification
Single value
Diuron <0,000020 mg/l
below limit of quantification
Single value
Ethofumesate <0,000020 mg/l
below limit of quantification
Single value
Fenuron <0,000020 mg/l
below limit of quantification
Single value
Flufenacet <0,000020 mg/l
below limit of quantification
Single value
Fluoride 0,10 mg/l 1.5 mg/l
7 %
Single value
Glyphosate <0,000050 mg/l
below limit of quantification
Single value
Haloacetic acids (HAA) <0,0030 mg/l
below limit of quantification
60 µg/l
< 5 % *
Single value
Hexazinone <0,000020 mg/l
below limit of quantification
Single value
Imidacloprid <0,000020 mg/l
below limit of quantification
Single value
Isoproturon <0,000020 mg/l
below limit of quantification
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
MCPA <0,000020 mg/l
below limit of quantification
Single value
Mecoprop <0,000020 mg/l
below limit of quantification
Single value
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Metalaxyl <0,000020 mg/l
below limit of quantification
Single value
Metamitron <0,000020 mg/l
below limit of quantification
Single value
Metazachlor <0,000020 mg/l
below limit of quantification
Single value
Metazachlor acid <0,000050 mg/l
below limit of quantification
Single value
Metazachlor sulfonic acid 0,000076 mg/l Single value
Methabenzthiazuron <0,000020 mg/l
below limit of quantification
Single value
Metobromuron <0,000020 mg/l
below limit of quantification
Single value
Metolachlor <0,000020 mg/l
below limit of quantification
Single value
Metolachlor acid <0,000050 mg/l
below limit of quantification
Single value
Metolachlor sulfonic acid <0,000050 mg/l
below limit of quantification
Single value
Metoxuron <0,000020 mg/l
below limit of quantification
Single value
Metribuzin <0,000020 mg/l
below limit of quantification
Single value
Nickel 0,008 mg/l 20 µg/l
40 %
Single value
Nicosulfuron <0,000020 mg/l
below limit of quantification
Single value
Nitrate 5,3 mg/l 50 mg/l
11 %
Single value
Nitrite <0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value
Pendimethalin <0,000020 mg/l
below limit of quantification
Single value
Prometryn <0,000020 mg/l
below limit of quantification
Single value
Propazine <0,000020 mg/l
below limit of quantification
Single value
Quinmerac <0,000020 mg/l
below limit of quantification
Single value
Selenium 0,001 mg/l 10 µg/l
10 %
Single value
Simazine <0,000020 mg/l
below limit of quantification
Single value
Terbuthylazine <0,000020 mg/l
below limit of quantification
Single value
Terbutryn <0,000020 mg/l
below limit of quantification
Single value
Tetrachloroethene <0,00030 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) 0,00052 mg/l Single value
Trichloroacetic acid <0,0030 mg/l
below limit of quantification
Single value
Trichloroethene <0,00030 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) <0,00030 mg/l
below limit of quantification
Single value
Trihalomethanes — Total 0,00052 mg/l 50 µg/l
1 %
Single value
Uranium 0,00039 mg/l 10 µg/l
4 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Metabolites (1)

Metabolites – Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße
Parameter Value Parametric value Share of the parametric value Reference
Desphenyl-chloridazon <0,000050 mg/l
below limit of quantification
Single value

Indicator parameters (18)

Indicator parameters – Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Ammonium <0,020 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value
Calcite dissolution capacity <5,00 mg/l
below limit of quantification
5 mg/l CaCO3 Single value
Chloride 29,7 mg/l 250 mg/l
12 %
Single value
Clostridium perfringens (including spores) 0 Anzahl/100ml 0/100 ml Single value
Coliform bacteria 0 Anzahl/100ml 0/100 ml Single value
Colony count 22 °C 1 Anzahl/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colour <0,1 1/m
below limit of quantification
0.5 m⁻¹ Single value
Iron 0,010 mg/l 0.2 mg/l
5 %
Single value
Manganese 0,003 mg/l 50 µg/l
6 %
Single value
pH 7,5 6,5–9,5 Single value
Sodium 11,8 mg/l 200 mg/l
6 %
Single value
Sulphate 95 mg/l 250 mg/l
38 %
Single value
Taste ohne für den Verbraucher annehmbar Single value
Temperature 8,3 °C Single value
Total organic carbon (TOC) 0,92 mg/l ohne anormale Veränderung Single value
Turbidity 0,15 FNU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Treatment substances (1)

Treatment substances – Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße
Parameter Value Parametric value Share of the parametric value Reference
Free chlorine <0,02 mg/l
below limit of quantification
Single value

Further parameters (9)

Further parameters – Wasserversorgungsgebiet Reichenbach, HB Zwickauer Straße
Parameter Value Parametric value Share of the parametric value Reference
Barium 0,02 mg/l Single value
Calcium 82,0 mg/l Single value
Magnesium 14,1 mg/l Single value
Oxygen 10,6 mg/l Single value
Phosphate 0,022 mg/l Single value
Potassium 1,3 mg/l Single value
Silicate / silicic acid 13,5 mg/l Single value
Total hardness 14,7 °dH Single value
Zinc 0,007 mg/l Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://api.wasserportal.info/api/public/qualitaet/trinkwasseranalyse/9bd54da6-fff9-4455-b592-671e233e683f · 21.01.2026 · Probenahme 12.01.2026 08:00, Prüfzeitraum 12.01.2026 bis 21.01.2026 · retrieved on 11/07/2026

Postcodes in this zone: 08239

Show 6 more supply zones

Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof

ZWAV (Zweckverband Wasserversorgung und Abwasserentsorgung Vogtland)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
9.7 °dH
Hardness range medium
Key values Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 11 mg/l 50 mg/l
22 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Sulphate 22 mg/l 250 mg/l
9 %
Single value
Sodium 5,50 mg/l 200 mg/l
3 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (112 — most recent value per parameter)

Microbiology (2)

Microbiology – Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Intestinal enterococci 0 Anzahl/100ml 0/100 ml Single value

Chemical parameters (80)

Chemical parameters – Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00090 mg/l
below limit of quantification
3 µg/l
< 30 % *
Single value
2,4-D <0,000020 mg/l
below limit of quantification
Single value
Antimony <0,0010 mg/l
below limit of quantification
5 µg/l
< 20 % *
Single value
Arsenic <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Atrazine <0,000020 mg/l
below limit of quantification
Single value
Azoxystrobin <0,000020 mg/l
below limit of quantification
Single value
Bentazone <0,000020 mg/l
below limit of quantification
Single value
Benzene <0,00050 mg/l
below limit of quantification
1 µg/l
< 50 % *
Single value
Benzo(a)pyrene <0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Benzo(b)fluoranthene <0,00001 mg/l
below limit of quantification
Single value
Benzo(ghi)perylene <0,00001 mg/l
below limit of quantification
Single value
Benzo(k)fluoranthene <0,00001 mg/l
below limit of quantification
Single value
Boron <0,010 mg/l
below limit of quantification
1 mg/l
< 1 % *
Single value
Boscalid <0,000020 mg/l
below limit of quantification
Single value
Bromacil <0,000020 mg/l
below limit of quantification
Single value
Bromate <0,0025 mg/l
below limit of quantification
10 µg/l
< 25 % *
Single value
Bromodichloromethane <0,00030 mg/l
below limit of quantification
Single value
Bromoxynil <0,000020 mg/l
below limit of quantification
Single value
Cadmium 0,0002 mg/l 3 µg/l
7 %
Single value
Carbendazim <0,000020 mg/l
below limit of quantification
Single value
Chlorate <0,010 mg/l
below limit of quantification
70 µg/l
< 14 % *
Single value
Chloridazon <0,000020 mg/l
below limit of quantification
Single value
Chlorotoluron <0,000020 mg/l
below limit of quantification
Single value
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper 0,0042 mg/l 2 mg/l
0.2 %
Single value
Cyanazine <0,000020 mg/l
below limit of quantification
Single value
Cyanide <0,01 mg/l
below limit of quantification
50 µg/l
< 20 % *
Single value
Desethylatrazine <0,000020 mg/l
below limit of quantification
Single value
Desisopropylatrazine <0,000020 mg/l
below limit of quantification
Single value
Dibromochloromethane 0,0010 mg/l Single value
Dichlorprop <0,000020 mg/l
below limit of quantification
Single value
Diflufenican <0,000020 mg/l
below limit of quantification
Single value
Dimefuron <0,000020 mg/l
below limit of quantification
Single value
Dimethachlor <0,000020 mg/l
below limit of quantification
Single value
Dimethachlor sulfonic acid 0,000024 mg/l Single value
Dimethenamid <0,000020 mg/l
below limit of quantification
Single value
Dimethoate <0,000020 mg/l
below limit of quantification
Single value
Diuron <0,000020 mg/l
below limit of quantification
Single value
Ethofumesate <0,000020 mg/l
below limit of quantification
Single value
Fenuron <0,000020 mg/l
below limit of quantification
Single value
Flufenacet <0,000020 mg/l
below limit of quantification
Single value
Fluoride 0,10 mg/l 1.5 mg/l
7 %
Single value
Glyphosate <0,000050 mg/l
below limit of quantification
Single value
Hexazinone <0,000020 mg/l
below limit of quantification
Single value
Imidacloprid <0,000020 mg/l
below limit of quantification
Single value
Isoproturon <0,000020 mg/l
below limit of quantification
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
MCPA <0,000020 mg/l
below limit of quantification
Single value
Mecoprop <0,000020 mg/l
below limit of quantification
Single value
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Metalaxyl <0,000020 mg/l
below limit of quantification
Single value
Metamitron <0,000020 mg/l
below limit of quantification
Single value
Metazachlor <0,000020 mg/l
below limit of quantification
Single value
Metazachlor acid <0,000050 mg/l
below limit of quantification
Single value
Metazachlor sulfonic acid 0,00024 mg/l Single value
Methabenzthiazuron <0,000020 mg/l
below limit of quantification
Single value
Metobromuron <0,000020 mg/l
below limit of quantification
Single value
Metolachlor <0,000020 mg/l
below limit of quantification
Single value
Metolachlor acid <0,000050 mg/l
below limit of quantification
Single value
Metolachlor sulfonic acid <0,000050 mg/l
below limit of quantification
Single value
Metoxuron <0,000020 mg/l
below limit of quantification
Single value
Metribuzin <0,000020 mg/l
below limit of quantification
Single value
Nickel 0,006 mg/l 20 µg/l
30 %
Single value
Nicosulfuron <0,000020 mg/l
below limit of quantification
Single value
Nitrate 11 mg/l 50 mg/l
22 %
Single value
Nitrite <0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value
Pendimethalin <0,000020 mg/l
below limit of quantification
Single value
Prometryn <0,000020 mg/l
below limit of quantification
Single value
Propazine <0,000020 mg/l
below limit of quantification
Single value
Quinmerac <0,000020 mg/l
below limit of quantification
Single value
Selenium <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Simazine <0,000020 mg/l
below limit of quantification
Single value
Terbuthylazine <0,000020 mg/l
below limit of quantification
Single value
Terbutryn <0,000020 mg/l
below limit of quantification
Single value
Tetrachloroethene <0,00030 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) 0,0030 mg/l Single value
Trichloroethene <0,00030 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) <0,00030 mg/l
below limit of quantification
Single value
Trihalomethanes — Total 0,0040 mg/l 50 µg/l
8 %
Single value
Uranium 0,00011 mg/l 10 µg/l
1 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Metabolites (1)

Metabolites – Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof
Parameter Value Parametric value Share of the parametric value Reference
Desphenyl-chloridazon <0,000050 mg/l
below limit of quantification
Single value

Indicator parameters (19)

Indicator parameters – Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Ammonium <0,020 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value
Calcite dissolution capacity <5,00 mg/l
below limit of quantification
5 mg/l CaCO3 Single value
Chloride 13,2 mg/l 250 mg/l
5 %
Single value
Clostridium perfringens (including spores) 0 Anzahl/100ml 0/100 ml Single value
Coliform bacteria 0 Anzahl/100ml 0/100 ml Single value
Colony count 22 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colour <0,1 1/m
below limit of quantification
0.5 m⁻¹ Single value
Iron <0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Manganese <0,001 mg/l
below limit of quantification
50 µg/l
< 2 % *
Single value
Oxidisability <0,5 mg/l
below limit of quantification
5 mg/l O2 Single value
pH 7,6 6,5–9,5 Single value
Sodium 5,50 mg/l 200 mg/l
3 %
Single value
Sulphate 22 mg/l 250 mg/l
9 %
Single value
Taste ohne für den Verbraucher annehmbar Single value
Temperature 10,4 °C Single value
Total organic carbon (TOC) 0,28 mg/l ohne anormale Veränderung Single value
Turbidity 0,12 FNU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Treatment substances (1)

Treatment substances – Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof
Parameter Value Parametric value Share of the parametric value Reference
Free chlorine <0,01 mg/l
below limit of quantification
Single value

Further parameters (9)

Further parameters – Wasserversorgungsgebiet Reichenbach, Mylau, Netzschkau - WW Bauhof
Parameter Value Parametric value Share of the parametric value Reference
Barium 0,03 mg/l Single value
Calcium 55,3 mg/l Single value
Magnesium 8,61 mg/l Single value
Oxygen 9,56 mg/l Single value
Phosphate 0,050 mg/l Single value
Potassium 1,4 mg/l Single value
Silicate / silicic acid 13,6 mg/l Single value
Total hardness 9,7 °dH Single value
Zinc 0,010 mg/l Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://api.wasserportal.info/api/public/qualitaet/trinkwasseranalyse/ede22a15-7671-4d4f-a972-0e9d7a37aea6 · 05.12.2025 · Probenahme 24.11.2025 12:20, Prüfzeitraum 24.11.2025 bis 05.12.2025 · retrieved on 27/07/2026

Postcodes in this zone: 08239

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2020. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Water hardness
3.8 °dH
Hardness range soft
Key values WW MULDENBERG
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 3.1 mg/l 50 mg/l
6 %
Mean
Sulphate 11.82 mg/l 250 mg/l
5 %
Mean
Show all recorded parameters (8 — most recent value per parameter)

Chemical parameters (2)

Chemical parameters – WW MULDENBERG
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 3.1 mg/l 50 mg/l
6 %
Mean
Uranium <0.0001 mg/l
below limit of quantification
10 µg/l
< 1 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (5)

Indicator parameters – WW MULDENBERG
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0.02 mg/l 0.2 mg/l
10 %
Mean
Iron 0.03 mg/l 0.2 mg/l
15 %
Mean
Manganese 0.01 mg/l 50 µg/l
20 %
Mean
pH 8.1 - 6,5–9,5 Mean
Sulphate 11.82 mg/l 250 mg/l
5 %
Mean

Further parameters (1)

Further parameters – WW MULDENBERG
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 3.8 °dH Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://apps.gesunde.sachsen.de/trinkwasser/trinkwasser-detail-WSZ_DESN_1030-de.html · aktualisiert am 16.05.2023 · Jahr 2020 · retrieved on 11/07/2026

Postcodes in this zone: 08239

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2020. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Water hardness
3.3 °dH
Hardness range soft
Key values WW WERDA
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4.0 mg/l 50 mg/l
8 %
Mean
Sulphate 15.51 mg/l 250 mg/l
6 %
Mean
Show all recorded parameters (8 — most recent value per parameter)

Chemical parameters (2)

Chemical parameters – WW WERDA
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4.0 mg/l 50 mg/l
8 %
Mean
Uranium <0.0001 mg/l
below limit of quantification
10 µg/l
< 1 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (5)

Indicator parameters – WW WERDA
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0.02 mg/l 0.2 mg/l
10 %
Mean
Iron 0.02 mg/l 0.2 mg/l
10 %
Mean
Manganese 0.02 mg/l 50 µg/l
40 %
Mean
pH 8.0 - 6,5–9,5 Mean
Sulphate 15.51 mg/l 250 mg/l
6 %
Mean

Further parameters (1)

Further parameters – WW WERDA
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 3.3 °dH Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://apps.gesunde.sachsen.de/trinkwasser/trinkwasser-detail-WSZ_DESN_1010-de.html · aktualisiert am 16.05.2023 · Jahr 2020 · retrieved on 11/07/2026

Postcodes in this zone: 08239

WW WERDA (Sachsen, WSZ 1010)

WW WERDA

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2020. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Water hardness
3.3 °dH
Hardness range soft
Key values WW WERDA (Sachsen, WSZ 1010)
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4.0 mg/l 50 mg/l
8 %
Mean
Sulphate 15.51 mg/l 250 mg/l
6 %
Mean
Show all recorded parameters (8 — most recent value per parameter)

Chemical parameters (2)

Chemical parameters – WW WERDA (Sachsen, WSZ 1010)
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4.0 mg/l 50 mg/l
8 %
Mean
Uranium <0.0001 mg/l
below limit of quantification
10 µg/l
< 1 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (5)

Indicator parameters – WW WERDA (Sachsen, WSZ 1010)
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0.02 mg/l 0.2 mg/l
10 %
Mean
Iron 0.02 mg/l 0.2 mg/l
10 %
Mean
Manganese 0.02 mg/l 50 µg/l
40 %
Mean
pH 8.0 - 6,5–9,5 Mean
Sulphate 15.51 mg/l 250 mg/l
6 %
Mean

Further parameters (1)

Further parameters – WW WERDA (Sachsen, WSZ 1010)
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 3.3 °dH Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://apps.gesunde.sachsen.de/trinkwasser/trinkwasser-detail-WSZ_DESN_1010-de.html · Jahresdurchschnitt 2020 · retrieved on 11/07/2026

Postcodes in this zone: 08239

1210020 Fernwasser HB7000 Plohn, Abhorn, Röthenbach

ZWAV (Zweckverband Wasserversorgung und Abwasserentsorgung Vogtland)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.5 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – 1210020 Fernwasser HB7000 Plohn, Abhorn, Röthenbach
Parameter Value Parametric value Share of the parametric value Reference
pH 7,8 6,5–9,5 Mean · 1210020 Fernwasser HB7000 Plohn, Abhorn, Röthenbach

Further parameters (2)

Further parameters – 1210020 Fernwasser HB7000 Plohn, Abhorn, Röthenbach
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · 1210020 Fernwasser HB7000 Plohn, Abhorn, Röthenbach
Total hardness 3,5 °dH Single value · 1210020 Fernwasser HB7000 Plohn, Abhorn, Röthenbach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 08239

3210018 Muldenhammer, Rützengrün, Vogelsgrün

ZWAV (Zweckverband Wasserversorgung und Abwasserentsorgung Vogtland)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
4.1 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – 3210018 Muldenhammer, Rützengrün, Vogelsgrün
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Mean · 3210018 Muldenhammer, Rützengrün, Vogelsgrün

Further parameters (2)

Further parameters – 3210018 Muldenhammer, Rützengrün, Vogelsgrün
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · 3210018 Muldenhammer, Rützengrün, Vogelsgrün
Total hardness 4,1 °dH Single value · 3210018 Muldenhammer, Rützengrün, Vogelsgrün

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Postcodes in this zone: 08239

Bergen (55608)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5.6 °dH
Hardness range soft
Key values HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS < 0.02 µg/L
below limit of quantification
0.1 µg/l
< 20 % *
Mean · HB Silberich
Nitrate 3.4 mg/L 50 mg/l
7 %
Mean · HB Silberich
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · HB Silberich
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · HB Silberich
Sulphate 16 mg/L 250 mg/l
6 %
Mean · HB Silberich
Sodium 7.3 mg/L 200 mg/l
4 %
Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · HB Silberich

Chemical parameters (14)

Chemical parameters – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · HB Silberich
Arsenic < 2 µg/L
below limit of quantification
10 µg/l
< 20 % *
Mean · HB Silberich
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · HB Silberich
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · HB Silberich
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · HB Silberich
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · HB Silberich
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · HB Silberich
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · HB Silberich
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · HB Silberich
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · HB Silberich
Nitrate 3.4 mg/L 50 mg/l
7 %
Mean · HB Silberich
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · HB Silberich
Selenium 4 µg/L 10 µg/l
40 %
Mean · HB Silberich
Uranium < 0.5 µg/L
below limit of quantification
10 µg/l
< 5 % *
Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS < 0.02 µg/L
below limit of quantification
0.1 µg/l
< 20 % *
Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (10)

Indicator parameters – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · HB Silberich
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · HB Silberich
Chloride 11 mg/L 250 mg/l
4 %
Mean · HB Silberich
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · HB Silberich
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · HB Silberich
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · HB Silberich
pH 8.1 - 6,5–9,5 Mean · HB Silberich
Sodium 7.3 mg/L 200 mg/l
4 %
Mean · HB Silberich
Sulphate 16 mg/L 250 mg/l
6 %
Mean · HB Silberich
Temperature 13.9 °C Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Calcium 35 mg/L Mean · HB Silberich
Magnesium 2.5 mg/L Mean · HB Silberich
Potassium < 0.3 mg/L
below limit of quantification
Mean · HB Silberich
Total hardness 0.99 mmol/l Mean · HB Silberich

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541695087/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Postcodes in this zone: 55608

Show 4 more supply zones

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
16.4 °dH
Hardness range hard
Key values Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.01 µg/L 0.1 µg/l
10 %
Mean · Limbach-Großbachtal
Nitrate 34 mg/L 50 mg/l
68 %
Mean · Limbach-Großbachtal
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Limbach-Großbachtal
Sulphate 29 mg/L 250 mg/l
12 %
Mean · Limbach-Großbachtal
Sodium 14.1 mg/L 200 mg/l
7 %
Mean · Limbach-Großbachtal

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Limbach-Großbachtal

Chemical parameters (14)

Chemical parameters – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · Limbach-Großbachtal
Arsenic 4 µg/L 10 µg/l
40 %
Mean · Limbach-Großbachtal
Boron 0.03 mg/L 1 mg/l
3 %
Mean · Limbach-Großbachtal
Cadmium < 0.2 µg/L
below limit of quantification
3 µg/l
< 7 % *
Mean · Limbach-Großbachtal
Copper < 0.005 mg/L
below limit of quantification
2 mg/l
< 0.3 % *
Mean · Limbach-Großbachtal
Cyanide < 0.003 mg/L
below limit of quantification
50 µg/l
< 6 % *
Mean · Limbach-Großbachtal
Fluoride 0.14 mg/L 1.5 mg/l
9 %
Mean · Limbach-Großbachtal
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Nickel < 5 µg/L
below limit of quantification
20 µg/l
< 25 % *
Mean · Limbach-Großbachtal
Nitrate 34 mg/L 50 mg/l
68 %
Mean · Limbach-Großbachtal
Nitrite 0.008 mg/L 0.5 mg/l
2 %
Mean · Limbach-Großbachtal
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Uranium 4 µg/L 10 µg/l
40 %
Mean · Limbach-Großbachtal

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.01 µg/L 0.1 µg/l
10 %
Mean · Limbach-Großbachtal

Indicator parameters (10)

Indicator parameters – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.005 mg/L
below limit of quantification
0.2 mg/l
< 3 % *
Mean · Limbach-Großbachtal
Ammonium 0.04 mg/L 0.5 mg/l
8 %
Mean · Limbach-Großbachtal
Chloride 27 mg/L 250 mg/l
11 %
Mean · Limbach-Großbachtal
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Limbach-Großbachtal
Iron < 0.05 mg/L
below limit of quantification
0.2 mg/l
< 25 % *
Mean · Limbach-Großbachtal
Manganese < 0.01 mg/L
below limit of quantification
50 µg/l
< 20 % *
Mean · Limbach-Großbachtal
pH 7.68 - 6,5–9,5 Mean · Limbach-Großbachtal
Sodium 14.1 mg/L 200 mg/l
7 %
Mean · Limbach-Großbachtal
Sulphate 29 mg/L 250 mg/l
12 %
Mean · Limbach-Großbachtal
Temperature 9.5 °C Mean · Limbach-Großbachtal

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Calcium 82 mg/L Mean · Limbach-Großbachtal
Magnesium 20.4 mg/L Mean · Limbach-Großbachtal
Potassium 2.8 mg/L Mean · Limbach-Großbachtal
Total hardness 2.93 mmol/l Mean · Limbach-Großbachtal

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541699500/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Postcodes in this zone: 55608

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
4.5 °dH
Hardness range soft
Key values Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Steinbachtalsperre
Nitrate 1.6 mg/L 50 mg/l
3 %
Mean · Steinbachtalsperre
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Steinbachtalsperre
Sulphate 18 mg/L 250 mg/l
7 %
Mean · Steinbachtalsperre
Sodium 7.6 mg/L 200 mg/l
4 %
Mean · Steinbachtalsperre

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (31 — most recent value per parameter)

Microbiology (1)

Microbiology – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Steinbachtalsperre

Chemical parameters (14)

Chemical parameters – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Antimony 3 µg/L 5 µg/l
60 %
Mean · Steinbachtalsperre
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · Steinbachtalsperre
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · Steinbachtalsperre
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · Steinbachtalsperre
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Steinbachtalsperre
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · Steinbachtalsperre
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Steinbachtalsperre
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Steinbachtalsperre
Nitrate 1.6 mg/L 50 mg/l
3 %
Mean · Steinbachtalsperre
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · Steinbachtalsperre
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Uranium < 0.2 µg/L
below limit of quantification
10 µg/l
< 2 % *
Mean · Steinbachtalsperre

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Steinbachtalsperre

Indicator parameters (10)

Indicator parameters – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Steinbachtalsperre
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · Steinbachtalsperre
Chloride 12 mg/L 250 mg/l
5 %
Mean · Steinbachtalsperre
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Steinbachtalsperre
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · Steinbachtalsperre
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Steinbachtalsperre
pH 8 - 6,5–9,5 Mean · Steinbachtalsperre
Sodium 7.6 mg/L 200 mg/l
4 %
Mean · Steinbachtalsperre
Sulphate 18 mg/L 250 mg/l
7 %
Mean · Steinbachtalsperre
Temperature 13.8 °C Mean · Steinbachtalsperre

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (5)

Further parameters – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Calcium 36 mg/L Mean · Steinbachtalsperre
Magnesium 2.6 mg/L Mean · Steinbachtalsperre
Potassium < 0.3 mg/L
below limit of quantification
Mean · Steinbachtalsperre
Total hardness 0.8 mmol/l Mean · Steinbachtalsperre
Zinc 0.006 mg/L Mean · Steinbachtalsperre

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541695100/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Postcodes in this zone: 55608

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.3 °dH
Hardness range soft
Key values Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Stipshausen
Nitrate 7.3 mg/L 50 mg/l
15 %
Mean · Stipshausen
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Stipshausen
Sulphate 5.1 mg/L 250 mg/l
2 %
Mean · Stipshausen
Sodium 4.8 mg/L 200 mg/l
2 %
Mean · Stipshausen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Stipshausen

Chemical parameters (14)

Chemical parameters – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Antimony 1 µg/L 5 µg/l
20 %
Mean · Stipshausen
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · Stipshausen
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · Stipshausen
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · Stipshausen
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Stipshausen
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · Stipshausen
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Stipshausen
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Stipshausen
Nitrate 7.3 mg/L 50 mg/l
15 %
Mean · Stipshausen
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · Stipshausen
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Uranium < 0.2 µg/L
below limit of quantification
10 µg/l
< 2 % *
Mean · Stipshausen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Stipshausen

Indicator parameters (10)

Indicator parameters – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0.024 mg/L 0.2 mg/l
12 %
Mean · Stipshausen
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · Stipshausen
Chloride 9.3 mg/L 250 mg/l
4 %
Mean · Stipshausen
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Stipshausen
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · Stipshausen
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Stipshausen
pH 8.2 - 6,5–9,5 Mean · Stipshausen
Sodium 4.8 mg/L 200 mg/l
2 %
Mean · Stipshausen
Sulphate 5.1 mg/L 250 mg/l
2 %
Mean · Stipshausen
Temperature 10 °C Mean · Stipshausen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Calcium 21 mg/L Mean · Stipshausen
Magnesium 1.4 mg/L Mean · Stipshausen
Potassium < 0.3 mg/L
below limit of quantification
Mean · Stipshausen
Total hardness 0.58 mmol/l Mean · Stipshausen

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2542695029/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Postcodes in this zone: 55608

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.9 °dH
Hardness range soft
Key values WiLa
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · WiLa
Nitrate 6.7 mg/L 50 mg/l
13 %
Mean · WiLa
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · WiLa
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · WiLa
Sulphate 6.7 mg/L 250 mg/l
3 %
Mean · WiLa
Sodium 3.7 mg/L 200 mg/l
2 %
Mean · WiLa

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · WiLa

Chemical parameters (14)

Chemical parameters – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Antimony 1 µg/L 5 µg/l
20 %
Mean · WiLa
Arsenic 4 µg/L 10 µg/l
40 %
Mean · WiLa
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · WiLa
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · WiLa
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · WiLa
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · WiLa
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · WiLa
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · WiLa
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · WiLa
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · WiLa
Nitrate 6.7 mg/L 50 mg/l
13 %
Mean · WiLa
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · WiLa
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · WiLa
Uranium < 0.2 µg/L
below limit of quantification
10 µg/l
< 2 % *
Mean · WiLa

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · WiLa

Indicator parameters (10)

Indicator parameters – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · WiLa
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · WiLa
Chloride 7.2 mg/L 250 mg/l
3 %
Mean · WiLa
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · WiLa
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · WiLa
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · WiLa
pH 8.3 - 6,5–9,5 Mean · WiLa
Sodium 3.7 mg/L 200 mg/l
2 %
Mean · WiLa
Sulphate 6.7 mg/L 250 mg/l
3 %
Mean · WiLa
Temperature 11.8 °C Mean · WiLa

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Calcium 23 mg/L Mean · WiLa
Magnesium 1.4 mg/L Mean · WiLa
Potassium < 0.3 mg/L
below limit of quantification
Mean · WiLa
Total hardness 0.7 mmol/l Mean · WiLa

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541695302/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Postcodes in this zone: 55608

Frequently asked questions about drinking water in Bergen

How hard is the water in Bergen?
TWIST RLP - HB Silberich publishes a total hardness of 0.99 mmol/l for the supply zone HB Silberich — that corresponds to 5.6 °dH. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 13/07/2026.
How much nitrate is in the drinking water in Bergen?
TWIST RLP - HB Silberich publishes a nitrate value of 3.4 mg/L for the supply zone HB Silberich. The statutory parametric value is 50 mg/l; the measured value represents 7 % of the parametric value. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Are PFAS detectable in the drinking water in Bergen?
TWIST RLP - HB Silberich publishes for the supply zone HB Silberich a sum value PFAS-20 below the limit of quantification (entry in the report: "< 0.02 µg/L"). This is not to be read as "PFAS-free": below the limit of quantification, the measurement cannot make any statement. The statutory parametric value is 0.1 µg/l; the measured value lies below it and cannot be specified more precisely below the limit of quantification. For the sum of the 20 individual substances, this parametric value has applied since 12/01/2026. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Who supplies the drinking water in Bergen?
TWIST RLP - HB Silberich. The values shown here come from the supply zone HB Silberich and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.

No data yet

For 2 postcodes 29468, 83346 there is no verified assignment yet.