Skip to content
maunawai.info

Drinking water in Bergatreute

12 supply zones — values can differ depending on the district. Below is the zone with the most documented parameters, the others collapsed underneath. To determine the exact match, look up the postcode.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Arnach
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 12,0 mg/l 50 mg/l
24 %
Single value · Arnach
Sulphate 9,8 mg/l 250 mg/l
4 %
Single value · Arnach
Sodium 2,7 mg/l 200 mg/l
1 %
Single value · Arnach
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Arnach
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Arnach
Nitrate 12,0 mg/l 50 mg/l
24 %
Single value · Arnach
Uranium 0,0007 mg/l 10 µg/l
7 %
Single value · Arnach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Arnach
Parameter Value Parametric value Share of the parametric value Reference
Chloride <1 mg/l
below limit of quantification
250 mg/l
< 0.4 % *
Single value · Arnach
pH 7,73 6,5–9,5 Single value · Arnach
Sodium 2,7 mg/l 200 mg/l
1 %
Single value · Arnach
Sulphate 9,8 mg/l 250 mg/l
4 %
Single value · Arnach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (6)

Further parameters – Arnach
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 4,80 mmol/l Single value · Arnach
Base capacity to pH 8.2 0,145 mmol/l Single value · Arnach
Calcium 79,9 mg/l Single value · Arnach
Hydrogen carbonate 290 mg/l Single value · Arnach
Magnesium 8,1 mg/l Single value · Arnach
Potassium 0,4 mg/l Single value · Arnach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwurzach.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Show 11 more supply zones

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Bad Waldsee
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 15 mg/l 50 mg/l
30 %
Single value · Bad Waldsee
Sulphate 26 mg/l 250 mg/l
10 %
Single value · Bad Waldsee
Sodium 11,7 mg/l 200 mg/l
6 %
Single value · Bad Waldsee
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Bad Waldsee
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Bad Waldsee
Nitrate 15 mg/l 50 mg/l
30 %
Single value · Bad Waldsee
Uranium 0,0045 mg/l 10 µg/l
45 %
Single value · Bad Waldsee

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Bad Waldsee
Parameter Value Parametric value Share of the parametric value Reference
Chloride 21 mg/l 250 mg/l
8 %
Single value · Bad Waldsee
pH 7,14 6,5–9,5 Single value · Bad Waldsee
Sodium 11,7 mg/l 200 mg/l
6 %
Single value · Bad Waldsee
Sulphate 26 mg/l 250 mg/l
10 %
Single value · Bad Waldsee

Further parameters (6)

Further parameters – Bad Waldsee
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 6,9 mmol/l Single value · Bad Waldsee
Base capacity to pH 8.2 0,485 mmol/l Single value · Bad Waldsee
Calcium 107 mg/l Single value · Bad Waldsee
Hydrogen carbonate 423 mg/l Single value · Bad Waldsee
Magnesium 21,3 mg/l Single value · Bad Waldsee
Potassium 1,8 mg/l Single value · Bad Waldsee

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwaldsee.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Bad Wurzach
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 16 mg/l 50 mg/l
32 %
Single value · Bad Wurzach
Sulphate 7,1 mg/l 250 mg/l
3 %
Single value · Bad Wurzach
Sodium 6,1 mg/l 200 mg/l
3 %
Single value · Bad Wurzach
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Bad Wurzach
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Bad Wurzach
Nitrate 16 mg/l 50 mg/l
32 %
Single value · Bad Wurzach
Uranium 0,0005 mg/l 10 µg/l
5 %
Single value · Bad Wurzach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Bad Wurzach
Parameter Value Parametric value Share of the parametric value Reference
Chloride 7,1 mg/l 250 mg/l
3 %
Single value · Bad Wurzach
pH 7,39 6,5–9,5 Single value · Bad Wurzach
Sodium 6,1 mg/l 200 mg/l
3 %
Single value · Bad Wurzach
Sulphate 7,1 mg/l 250 mg/l
3 %
Single value · Bad Wurzach

Further parameters (6)

Further parameters – Bad Wurzach
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 6,4 mmol/l Single value · Bad Wurzach
Base capacity to pH 8.2 0,359 mmol/l Single value · Bad Wurzach
Calcium 98,7 mg/l Single value · Bad Wurzach
Hydrogen carbonate 388 mg/l Single value · Bad Wurzach
Magnesium 17,3 mg/l Single value · Bad Wurzach
Potassium 1,3 mg/l Single value · Bad Wurzach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwurzach.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Dietmanns
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 32,0 mg/l 50 mg/l
64 %
Single value · Dietmanns
Sulphate 8,7 mg/l 250 mg/l
3 %
Single value · Dietmanns
Sodium 7,1 mg/l 200 mg/l
4 %
Single value · Dietmanns
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Dietmanns
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Dietmanns
Nitrate 32,0 mg/l 50 mg/l
64 %
Single value · Dietmanns
Uranium 0,0004 mg/l 10 µg/l
4 %
Single value · Dietmanns

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Dietmanns
Parameter Value Parametric value Share of the parametric value Reference
Chloride 10 mg/l 250 mg/l
4 %
Single value · Dietmanns
pH 7,96 6,5–9,5 Single value · Dietmanns
Sodium 7,1 mg/l 200 mg/l
4 %
Single value · Dietmanns
Sulphate 8,7 mg/l 250 mg/l
3 %
Single value · Dietmanns

Further parameters (6)

Further parameters – Dietmanns
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 4,5 mmol/l Single value · Dietmanns
Base capacity to pH 8.2 0,103 mmol/l Single value · Dietmanns
Calcium 73,4 mg/l Single value · Dietmanns
Hydrogen carbonate 273 mg/l Single value · Dietmanns
Magnesium 15,2 mg/l Single value · Dietmanns
Potassium 0,5 mg/l Single value · Dietmanns

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwurzach.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Gaisbeuren
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 21 mg/l 50 mg/l
42 %
Single value · Gaisbeuren
Sulphate 18 mg/l 250 mg/l
7 %
Single value · Gaisbeuren
Sodium 6,6 mg/l 200 mg/l
3 %
Single value · Gaisbeuren
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Gaisbeuren
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Gaisbeuren
Nitrate 21 mg/l 50 mg/l
42 %
Single value · Gaisbeuren
Uranium 0,0009 mg/l 10 µg/l
9 %
Single value · Gaisbeuren

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Gaisbeuren
Parameter Value Parametric value Share of the parametric value Reference
Chloride 11 mg/l 250 mg/l
4 %
Single value · Gaisbeuren
pH 7,33 6,5–9,5 Single value · Gaisbeuren
Sodium 6,6 mg/l 200 mg/l
3 %
Single value · Gaisbeuren
Sulphate 18 mg/l 250 mg/l
7 %
Single value · Gaisbeuren

Further parameters (6)

Further parameters – Gaisbeuren
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 6,5 mmol/l Single value · Gaisbeuren
Base capacity to pH 8.2 0,27 mmol/l Single value · Gaisbeuren
Calcium 103 mg/l Single value · Gaisbeuren
Hydrogen carbonate 393 mg/l Single value · Gaisbeuren
Magnesium 20,7 mg/l Single value · Gaisbeuren
Potassium 1,2 mg/l Single value · Gaisbeuren

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwaldsee.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Haidgau
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 9,0 mg/l 50 mg/l
18 %
Single value · Haidgau
Sulphate 4,9 mg/l 250 mg/l
2 %
Single value · Haidgau
Sodium 3,5 mg/l 200 mg/l
2 %
Single value · Haidgau
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Haidgau
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Haidgau
Nitrate 9,0 mg/l 50 mg/l
18 %
Single value · Haidgau
Uranium 0,0004 mg/l 10 µg/l
4 %
Single value · Haidgau

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Haidgau
Parameter Value Parametric value Share of the parametric value Reference
Chloride 5,3 mg/l 250 mg/l
2 %
Single value · Haidgau
pH 7,72 6,5–9,5 Single value · Haidgau
Sodium 3,5 mg/l 200 mg/l
2 %
Single value · Haidgau
Sulphate 4,9 mg/l 250 mg/l
2 %
Single value · Haidgau

Further parameters (6)

Further parameters – Haidgau
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 5,9 mmol/l Single value · Haidgau
Base capacity to pH 8.2 0,199 mmol/l Single value · Haidgau
Calcium 92,5 mg/l Single value · Haidgau
Hydrogen carbonate 361 mg/l Single value · Haidgau
Magnesium 14 mg/l Single value · Haidgau
Potassium 0,9 mg/l Single value · Haidgau

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwurzach.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Haisterkirch
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 9,0 mg/l 50 mg/l
18 %
Single value · Haisterkirch
Sulphate 4,9 mg/l 250 mg/l
2 %
Single value · Haisterkirch
Sodium 3,5 mg/l 200 mg/l
2 %
Single value · Haisterkirch
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Haisterkirch
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Haisterkirch
Nitrate 9,0 mg/l 50 mg/l
18 %
Single value · Haisterkirch
Uranium 0,0004 mg/l 10 µg/l
4 %
Single value · Haisterkirch

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Haisterkirch
Parameter Value Parametric value Share of the parametric value Reference
Chloride 5,3 mg/l 250 mg/l
2 %
Single value · Haisterkirch
pH 7,72 6,5–9,5 Single value · Haisterkirch
Sodium 3,5 mg/l 200 mg/l
2 %
Single value · Haisterkirch
Sulphate 4,9 mg/l 250 mg/l
2 %
Single value · Haisterkirch

Further parameters (6)

Further parameters – Haisterkirch
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 5,9 mmol/l Single value · Haisterkirch
Base capacity to pH 8.2 0,199 mmol/l Single value · Haisterkirch
Calcium 92,5 mg/l Single value · Haisterkirch
Hydrogen carbonate 361 mg/l Single value · Haisterkirch
Magnesium 14 mg/l Single value · Haisterkirch
Potassium 0,9 mg/l Single value · Haisterkirch

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwaldsee.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Hauerz
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 19 mg/l 50 mg/l
38 %
Single value · Hauerz
Sulphate 5,9 mg/l 250 mg/l
2 %
Single value · Hauerz
Sodium 5 mg/l 200 mg/l
3 %
Single value · Hauerz
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Hauerz
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Hauerz
Nitrate 19 mg/l 50 mg/l
38 %
Single value · Hauerz
Uranium 0,0002 mg/l 10 µg/l
2 %
Single value · Hauerz

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Hauerz
Parameter Value Parametric value Share of the parametric value Reference
Chloride 7,2 mg/l 250 mg/l
3 %
Single value · Hauerz
pH 8,03 6,5–9,5 Single value · Hauerz
Sodium 5 mg/l 200 mg/l
3 %
Single value · Hauerz
Sulphate 5,9 mg/l 250 mg/l
2 %
Single value · Hauerz

Further parameters (6)

Further parameters – Hauerz
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 3,4 mmol/l Single value · Hauerz
Base capacity to pH 8.2 0,052 mmol/l Single value · Hauerz
Calcium 64,5 mg/l Single value · Hauerz
Hydrogen carbonate 208 mg/l Single value · Hauerz
Magnesium 4,7 mg/l Single value · Hauerz
Potassium 0,6 mg/l Single value · Hauerz

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwurzach.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Mennisweiler
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 5,1 mg/l 50 mg/l
10 %
Single value · Mennisweiler
Sulphate 4,1 mg/l 250 mg/l
2 %
Single value · Mennisweiler
Sodium 3,5 mg/l 200 mg/l
2 %
Single value · Mennisweiler
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Mennisweiler
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Mennisweiler
Nitrate 5,1 mg/l 50 mg/l
10 %
Single value · Mennisweiler
Uranium 0,0001 mg/l 10 µg/l
1 %
Single value · Mennisweiler

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Mennisweiler
Parameter Value Parametric value Share of the parametric value Reference
Chloride 4,6 mg/l 250 mg/l
2 %
Single value · Mennisweiler
pH 7,56 6,5–9,5 Single value · Mennisweiler
Sodium 3,5 mg/l 200 mg/l
2 %
Single value · Mennisweiler
Sulphate 4,1 mg/l 250 mg/l
2 %
Single value · Mennisweiler

Further parameters (6)

Further parameters – Mennisweiler
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 5,7 mmol/l Single value · Mennisweiler
Base capacity to pH 8.2 0,308 mmol/l Single value · Mennisweiler
Calcium 90,1 mg/l Single value · Mennisweiler
Hydrogen carbonate 354 mg/l Single value · Mennisweiler
Magnesium 14,8 mg/l Single value · Mennisweiler
Potassium 0,8 mg/l Single value · Mennisweiler

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwaldsee.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Michelwinnaden
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 24,0 mg/l 50 mg/l
48 %
Single value · Michelwinnaden
Sulphate 24,0 mg/l 250 mg/l
10 %
Single value · Michelwinnaden
Sodium 13,5 mg/l 200 mg/l
7 %
Single value · Michelwinnaden
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Michelwinnaden
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Michelwinnaden
Nitrate 24,0 mg/l 50 mg/l
48 %
Single value · Michelwinnaden
Uranium 0,0017 mg/l 10 µg/l
17 %
Single value · Michelwinnaden

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Michelwinnaden
Parameter Value Parametric value Share of the parametric value Reference
Chloride 20,0 mg/l 250 mg/l
8 %
Single value · Michelwinnaden
pH 7,43 6,5–9,5 Single value · Michelwinnaden
Sodium 13,5 mg/l 200 mg/l
7 %
Single value · Michelwinnaden
Sulphate 24,0 mg/l 250 mg/l
10 %
Single value · Michelwinnaden

Further parameters (6)

Further parameters – Michelwinnaden
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 6,8 mmol/l Single value · Michelwinnaden
Base capacity to pH 8.2 0,572 mmol/l Single value · Michelwinnaden
Calcium 103,0 mg/l Single value · Michelwinnaden
Hydrogen carbonate 415 mg/l Single value · Michelwinnaden
Magnesium 25,6 mg/l Single value · Michelwinnaden
Potassium 1,3 mg/l Single value · Michelwinnaden

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwaldsee.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Mittel- und Oberurbach
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 21 mg/l 50 mg/l
42 %
Single value · Mittel- und Oberurbach
Sulphate 18 mg/l 250 mg/l
7 %
Single value · Mittel- und Oberurbach
Sodium 6,6 mg/l 200 mg/l
3 %
Single value · Mittel- und Oberurbach
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Mittel- und Oberurbach
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Mittel- und Oberurbach
Nitrate 21 mg/l 50 mg/l
42 %
Single value · Mittel- und Oberurbach
Uranium 0,0009 mg/l 10 µg/l
9 %
Single value · Mittel- und Oberurbach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Mittel- und Oberurbach
Parameter Value Parametric value Share of the parametric value Reference
Chloride 11 mg/l 250 mg/l
4 %
Single value · Mittel- und Oberurbach
pH 7,33 6,5–9,5 Single value · Mittel- und Oberurbach
Sodium 6,6 mg/l 200 mg/l
3 %
Single value · Mittel- und Oberurbach
Sulphate 18 mg/l 250 mg/l
7 %
Single value · Mittel- und Oberurbach

Further parameters (6)

Further parameters – Mittel- und Oberurbach
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 6,5 mmol/l Single value · Mittel- und Oberurbach
Base capacity to pH 8.2 0,27 mmol/l Single value · Mittel- und Oberurbach
Calcium 103 mg/l Single value · Mittel- und Oberurbach
Hydrogen carbonate 393 mg/l Single value · Mittel- und Oberurbach
Magnesium 20,7 mg/l Single value · Mittel- und Oberurbach
Potassium 1,2 mg/l Single value · Mittel- und Oberurbach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwaldsee.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Oberschwarzach
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 35 mg/l 50 mg/l
70 %
Single value · Oberschwarzach
Sulphate 9,3 mg/l 250 mg/l
4 %
Single value · Oberschwarzach
Sodium 6 mg/l 200 mg/l
3 %
Single value · Oberschwarzach
Show all recorded parameters (13 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Oberschwarzach
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,15 mg/l
below limit of quantification
1.5 mg/l
< 10 % *
Single value · Oberschwarzach
Nitrate 35 mg/l 50 mg/l
70 %
Single value · Oberschwarzach
Uranium 0,0005 mg/l 10 µg/l
5 %
Single value · Oberschwarzach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (4)

Indicator parameters – Oberschwarzach
Parameter Value Parametric value Share of the parametric value Reference
Chloride 11 mg/l 250 mg/l
4 %
Single value · Oberschwarzach
pH 7,61 6,5–9,5 Single value · Oberschwarzach
Sodium 6 mg/l 200 mg/l
3 %
Single value · Oberschwarzach
Sulphate 9,3 mg/l 250 mg/l
4 %
Single value · Oberschwarzach

Further parameters (6)

Further parameters – Oberschwarzach
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 4,4 mmol/l Single value · Oberschwarzach
Base capacity to pH 8.2 0,231 mmol/l Single value · Oberschwarzach
Calcium 76,4 mg/l Single value · Oberschwarzach
Hydrogen carbonate 267 mg/l Single value · Oberschwarzach
Magnesium 14,1 mg/l Single value · Oberschwarzach
Potassium 0,4 mg/l Single value · Oberschwarzach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wvv-osg.de/analyse/badwurzach.html · retrieved on 11/07/2026

Postcodes in this zone: 88368

Frequently asked questions about drinking water in Bergatreute

How much nitrate is in the drinking water in Bergatreute?
Wasserversorgungsverband Obere Schussentalgruppe publishes a nitrate value of 12,0 mg/l for the supply zone Arnach. The statutory parametric value is 50 mg/l; the measured value represents 24 % of the parametric value. Basis: Publication by the water supplier, retrieved on 11/07/2026.
Who supplies the drinking water in Bergatreute?
Wasserversorgungsverband Obere Schussentalgruppe. The values shown here come from the supply zone Arnach and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.