Drinking water in 99518
For this postcode Apoldaer Wasser GmbH publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 3 underneath.
How to read the share of the parametric value
12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.
Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.
Bad Sulza
Apoldaer Wasser GmbHAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
Water hardness
33.2 °dH
Hardness range hard
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Nitrate | 16,0 mg/l | 50 mg/l | 32 % | Single value · Bad Sulza |
Show all recorded parameters (2 — most recent value per parameter)
Chemical parameters (1)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Nitrate | 16,0 mg/l | 50 mg/l | 32 % | Single value · Bad Sulza |
Further parameters (1)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Total hardness | 33,2 °dh | — | — | Single value · Bad Sulza |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://wasserapolda.de/wp-content/uploads/2024/12/Analysen-fuer-Homepage-Nitrat-und-Wasserhaerte.pdf · 12/2025 · retrieved on 12/08/2026
Show 3 more supply zones in this postcode
Bad Sulza - Mischwasser Pumpstation Lanitztal / Wasserwerk Wischroda
Apoldaer Wasser GmbHAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
Water hardness
33.2 °dH
Hardness range hard
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Nitrate | 16 mg/l | 50 mg/l | 32 % | Single value |
| Lead | 0,0002 mg/l | 10 µg/l | 2 % | Single value |
| Escherichia coli (E. coli) | 0 MPN/100 ml | 0/100 ml | — | Single value |
| Sulphate | 215 mg/l | 250 mg/l | 86 % | Single value |
| Sodium | 14 mg/l | 200 mg/l | 7 % | Single value |
Show all recorded parameters (60 — most recent value per parameter)
Microbiology (2)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Escherichia coli (E. coli) | 0 MPN/100 ml | 0/100 ml | — | Single value |
| Intestinal enterococci | 0 KBE/100 ml | 0/100 ml | — | Single value |
Chemical parameters (35)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| 1,2-dichloroethane | <0,0006 mg/l below limit of quantification | 3 µg/l | < 20 % * | Single value |
| Antimony | <0,0006 mg/l below limit of quantification | 5 µg/l | < 12 % * | Single value |
| Arsenic | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Benzene | <0,0002 mg/l below limit of quantification | 1 µg/l | < 20 % * | Single value |
| Benzo(a)pyrene | 0,0000008 mg/l | 10 ng/l | 8 % | Single value |
| Benzo(b)fluoranthene | 0,000001 mg/l | — | — | Single value |
| Benzo(ghi)perylene | <0,0000023 mg/l below limit of quantification | — | — | Single value |
| Benzo(k)fluoranthene | <0,0000009 mg/l below limit of quantification | — | — | Single value |
| Bisphenol A | <0,00009 mg/l below limit of quantification | 2.5 µg/l | < 4 % * | Single value |
| Boron | <0,13 mg/l below limit of quantification | 1 mg/l | < 13 % * | Single value |
| Bromate | 0,001 mg/l | 10 µg/l | 10 % | Single value |
| Bromodichloromethane | <0,002 mg/l below limit of quantification | — | — | Single value |
| Cadmium | <0,0002 mg/l below limit of quantification | 3 µg/l | < 7 % * | Single value |
| Chlorate | 0,02 mg/l | 70 µg/l | 29 % | Single value |
| Chlorite | <0,03 mg/l below limit of quantification | 0.2 mg/l | < 15 % * | Single value |
| Chromium | 0,00018 mg/l | 25 µg/l | 0.7 % | Single value |
| Copper | <0,1 mg/l below limit of quantification | 2 mg/l | < 5 % * | Single value |
| Cyanide | <0,002 mg/l below limit of quantification | 50 µg/l | < 4 % * | Single value |
| Dibromochloromethane | <0,002 mg/l below limit of quantification | — | — | Single value |
| Fluoride | 0,22 mg/l | 1.5 mg/l | 15 % | Single value |
| Indeno(1,2,3-cd)pyrene | <0,0000019 mg/l below limit of quantification | — | — | Single value |
| Lead | 0,0002 mg/l | 10 µg/l | 2 % | Single value |
| Mercury | <0,0001 mg/l below limit of quantification | 1 µg/l | < 10 % * | Single value |
| Nickel | <0,001 mg/l below limit of quantification | 20 µg/l | < 5 % * | Single value |
| Nitrate | 16 mg/l | 50 mg/l | 32 % | Single value |
| Nitrite | <0,06 mg/l below limit of quantification | 0.5 mg/l | < 12 % * | Single value |
| Polycyclic aromatic hydrocarbons | 0,000001 mg/l | 0.1 µg/l | 1 % | Single value |
| Selenium | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Tetrachloroethene | <0,001 mg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene and Trichloroethene (sum) | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Tribromomethane (bromoform) | 0,005 mg/l | — | — | Single value |
| Trichloroethene | <0,001 mg/l below limit of quantification | — | — | Single value |
| Trichloromethane (chloroform) | <0,002 mg/l below limit of quantification | — | — | Single value |
| Trihalomethanes — Total | 0,005 mg/l | 50 µg/l | 10 % | Single value |
| Uranium | 0,004 mg/l | 10 µg/l | 40 % | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Indicator parameters (17)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Aluminium | 0,006 mg/l | 0.2 mg/l | 3 % | Single value |
| Ammonium | <0,1 mg/l below limit of quantification | 0.5 mg/l | < 20 % * | Single value |
| Calcite dissolution capacity | -42,7 mg/l | 5 mg/l CaCO3 | — | Single value |
| Chloride | 41 mg/l | 250 mg/l | 16 % | Single value |
| Coliform bacteria | 0 MPN/100 ml | 0/100 ml | — | Single value |
| Colony count 22 °C | 0 KBE/1 ml | ohne anormale Veränderung | — | Single value |
| Colony count 36 °C | 0 KBE/1 ml | ohne anormale Veränderung | — | Single value |
| Iron | <0,009 mg/l below limit of quantification | 0.2 mg/l | < 5 % * | Single value |
| Manganese | <0,003 mg/l below limit of quantification | 50 µg/l | < 6 % * | Single value |
| Odour | ohne | für den Verbraucher annehmbar | — | Single value |
| pH | 7,51 | 6,5–9,5 | — | Single value |
| Sodium | 14 mg/l | 200 mg/l | 7 % | Single value |
| Sulphate | 215 mg/l | 250 mg/l | 86 % | Single value |
| Taste | ohne | für den Verbraucher annehmbar | — | Single value |
| Temperature | 18,1 °C | — | — | Single value |
| Total organic carbon (TOC) | 0,87 mg/l | ohne anormale Veränderung | — | Single value |
| Turbidity | 0,7 FNU | 1 NTU | — | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Further parameters (6)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Acid capacity to pH 4.3 | 6,86 mmol/l | — | — | Single value |
| Base capacity to pH 8.2 | 0,45 mmol/l | — | — | Single value |
| Calcium | 139 mg/l | — | — | Single value |
| Magnesium | 60,3 mg/l | — | — | Single value |
| Potassium | 6,15 mg/l | — | — | Single value |
| Total hardness | 33,2 °dH | — | — | Single value |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://wasserapolda.de/wp-content/uploads/2024/12/Analysen-fuer-Homepage-Bad-Sulza-1.pdf · Probenahme 03.09.2025 · retrieved on 12/08/2026
Wischroda (Finnewasser)
Apoldaer Wasser GmbHAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 06/05/2025. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.
Water hardness
17.8 °dH
Hardness range hard
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Sum of PFAS | n.b. not determined Unit not stated in the document | 0.1 µg/l | — | Single value · Source [2] |
| Nitrate | 11 mg/l | 50 mg/l | 22 % | Single value · Source [1] |
| Lead | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value · Source [1] |
| Escherichia coli (E. coli) | 0 MPN/100 ml | 0/100 ml | — | Single value · Source [1] |
| Sulphate | 81 mg/l | 250 mg/l | 32 % | Single value · Source [1] |
| Sodium | 6,6 mg/l | 200 mg/l | 3 % | Single value · Source [1] |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Show all recorded parameters (80 — most recent value per parameter)
Microbiology (2)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Escherichia coli (E. coli) | 0 MPN/100 ml | 0/100 ml | — | Single value · Source [1] |
| Intestinal enterococci | 0 KBE/100 ml | 0/100 ml | — | Single value · Source [1] |
Chemical parameters (36)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| 1,2-dichloroethane | <0,0005 mg/l below limit of quantification | 3 µg/l | < 17 % * | Single value · Source [1] |
| Antimony | <0,001 mg/l below limit of quantification | 5 µg/l | < 20 % * | Single value · Source [1] |
| Arsenic | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value · Source [1] |
| Benzene | <0,00025 mg/l below limit of quantification | 1 µg/l | < 25 % * | Single value · Source [1] |
| Benzo(a)pyrene | <0,000001 mg/l below limit of quantification | 10 ng/l | < 10 % * | Single value · Source [1] |
| Benzo(b)fluoranthene | <0,000001 mg/l below limit of quantification | — | — | Single value · Source [1] |
| Benzo(ghi)perylene | <0,000001 mg/l below limit of quantification | — | — | Single value · Source [1] |
| Benzo(k)fluoranthene | <0,000001 mg/l below limit of quantification | — | — | Single value · Source [1] |
| Bisphenol A | <0,00001 mg/l below limit of quantification | 2.5 µg/l | < 0.4 % * | Single value · Source [1] |
| Boron | <0,02 mg/l below limit of quantification | 1 mg/l | < 2 % * | Single value · Source [1] |
| Bromate | <0,0025 mg/l below limit of quantification | 10 µg/l | < 25 % * | Single value · Source [1] |
| Bromodichloromethane | 0,0006 mg/l | — | — | Single value · Source [1] |
| Cadmium | <0,0001 mg/l below limit of quantification | 3 µg/l | < 3 % * | Single value · Source [1] |
| Chlorate | <0,02 mg/l below limit of quantification | 70 µg/l | < 29 % * | Single value · Source [1] |
| Chlorite | <0,05 mg/l below limit of quantification | 0.2 mg/l | < 25 % * | Single value · Source [1] |
| Chromium | <0,0005 mg/l below limit of quantification | 25 µg/l | < 2 % * | Single value · Source [1] |
| Copper | <0,001 mg/l below limit of quantification | 2 mg/l | < < 0.1 % * | Single value · Source [1] |
| Cyanide | <0,005 mg/l below limit of quantification | 50 µg/l | < 10 % * | Single value · Source [1] |
| Dibromochloromethane | 0,0022 mg/l | — | — | Single value · Source [1] |
| Fluoride | 0,26 mg/l | 1.5 mg/l | 17 % | Single value · Source [1] |
| Haloacetic acids (HAA) | <0,001 mg/l below limit of quantification | — | — | Single value · Source [1] |
| Indeno(1,2,3-cd)pyrene | <0,000001 mg/l below limit of quantification | — | — | Single value · Source [1] |
| Lead | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value · Source [1] |
| Mercury | <0,0001 mg/l below limit of quantification | 1 µg/l | < 10 % * | Single value · Source [1] |
| Microcystin-LR | <0,05 µg/l below limit of quantification | — | — | Single value · Source [1] |
| Nickel | <0,001 mg/l below limit of quantification | 20 µg/l | < 5 % * | Single value · Source [1] |
| Nitrate | 11 mg/l | 50 mg/l | 22 % | Single value · Source [1] |
| Nitrite | <0,01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value · Source [1] |
| Polycyclic aromatic hydrocarbons | <0,000001 mg/l below limit of quantification | 0.1 µg/l | < 1 % * | Single value · Source [1] |
| Selenium | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value · Source [1] |
| Tetrachloroethene | <0,0005 mg/l below limit of quantification | — | — | Single value · Source [1] |
| Tetrachloroethene and Trichloroethene (sum) | <0,01 mg/l below limit of quantification | 10 µg/l | < 100 % * | Single value · Source [1] |
| Tribromomethane (bromoform) | 0,0047 mg/l | — | — | Single value · Source [1] |
| Trichloroethene | <0,0005 mg/l below limit of quantification | — | — | Single value · Source [1] |
| Trihalomethanes — Total | 0,0075 mg/l | 50 µg/l | 15 % | Single value · Source [1] |
| Uranium | 0,006 mg/l | 10 µg/l | 60 % | Single value · Source [1] |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
PFAS (17)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Perfluorobutane sulfonic acid (PFBS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorobutanoic acid (PFBA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorodecane sulfonic acid (PFDS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorododecanoic acid (PFDoDA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluoroheptane sulfonic acid (PFHpS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluoroheptanoic acid (PFHpA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorohexane sulfonic acid (PFHxS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorohexanoic acid (PFHxA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorononane sulfonic acid (PFNS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorononanoic acid (PFNA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorooctanesulfonic acid (PFOS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorooctanoic acid (PFOA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluoropentanesulfonic acid (PFPeS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluoropentanoic acid (PFPeA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluorotridecanesulfonic acid (PFTrDS) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Perfluoroundecanoic acid (PFUnDA) | <0,01 below limit of quantification | — | — | Single value · Source [2] |
| Sum of PFAS | n.b. not determined Unit not stated in the document | 0.1 µg/l | — | Single value · Source [2] |
Indicator parameters (18)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Aluminium | <0,006 mg/l below limit of quantification | 0.2 mg/l | < 3 % * | Single value · Source [1] |
| Ammonium | <0,06 mg/l below limit of quantification | 0.5 mg/l | < 12 % * | Single value · Source [1] |
| Calcite dissolution capacity | -6,8 mg/l | 5 mg/l CaCO3 | — | Single value · Source [1] |
| Chloride | 20 mg/l | 250 mg/l | 8 % | Single value · Source [1] |
| Coliform bacteria | 0 MPN/100 ml | 0/100 ml | — | Single value · Source [1] |
| Colony count 22 °C | 0 KBE/1 ml | ohne anormale Veränderung | — | Single value · Source [1] |
| Colony count 36 °C | 0 KBE/1 ml | ohne anormale Veränderung | — | Single value · Source [1] |
| Conductivity (25 °C) | 638 µS/cm | 2,790 µS/cm | — | Single value · Source [1] |
| Iron | 0,013 mg/l | 0.2 mg/l | 6 % | Single value · Source [1] |
| Manganese | <0,001 mg/l below limit of quantification | 50 µg/l | < 2 % * | Single value · Source [1] |
| Odour | geruchlos | für den Verbraucher annehmbar | — | Single value · Source [1] |
| pH | 7,48 | 6,5–9,5 | — | Single value · Source [1] |
| Sodium | 6,6 mg/l | 200 mg/l | 3 % | Single value · Source [1] |
| Sulphate | 81 mg/l | 250 mg/l | 32 % | Single value · Source [1] |
| Taste | ohne | für den Verbraucher annehmbar | — | Single value · Source [1] |
| Temperature | 7,8 °C | — | — | Single value · Source [1] |
| Total organic carbon (TOC) | 1 mg/l | ohne anormale Veränderung | — | Single value · Source [1] |
| Turbidity | 0,2 FNU | 1 NTU | — | Single value · Source [1] |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Further parameters (7)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Acid capacity to pH 4.3 | 4,5 mmol/l | — | — | Single value · Source [1] |
| Base capacity to pH 8.2 | 0,3 mmol/l | — | — | Single value · Source [1] |
| Calcium | 90,9 mg/l | — | — | Single value · Source [1] |
| Magnesium | 22 mg/l | — | — | Single value · Source [1] |
| Phosphate | 1,3 mg/l | — | — | Single value · Source [1] |
| Potassium | 4,4 mg/l | — | — | Single value · Source [1] |
| Total hardness | 17,8 °dH | — | — | Single value · Source [1] |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Sources: [1] https://wasserapolda.de/wp-content/uploads/2024/12/Analysen-fuer-Homepage-Wasserwerk-Januar-2026.pdf · Prüfbericht vom 13.01.2026 · Probenahme 06.05.2025 · retrieved on 12/08/2026 [2] https://wasserapolda.de/wp-content/uploads/2026/05/Analysen-fuer-Homepage-PFAS-Wasserwerk-2026.pdf · Probenahme am 13.01.2026 · retrieved on 12/08/2026
Großheringen - Mischwasser Pumpstation Großheringen / Wasserwerk Wischroda
Apoldaer Wasser GmbHAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
Water hardness
26.1 °dH
Hardness range hard
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Nitrate | 26 mg/l | 50 mg/l | 52 % | Single value |
| Lead | 0,0002 mg/l | 10 µg/l | 2 % | Single value |
| Escherichia coli (E. coli) | 0 MPN/100 ml | 0/100 ml | — | Single value |
| Sulphate | 127 mg/l | 250 mg/l | 51 % | Single value |
| Sodium | 8 mg/l | 200 mg/l | 4 % | Single value |
Show all recorded parameters (60 — most recent value per parameter)
Microbiology (2)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Escherichia coli (E. coli) | 0 MPN/100 ml | 0/100 ml | — | Single value |
| Intestinal enterococci | 0 KBE/100 ml | 0/100 ml | — | Single value |
Chemical parameters (35)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| 1,2-dichloroethane | <0,0006 mg/l below limit of quantification | 3 µg/l | < 20 % * | Single value |
| Antimony | <0,0006 mg/l below limit of quantification | 5 µg/l | < 12 % * | Single value |
| Arsenic | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Benzene | <0,0002 mg/l below limit of quantification | 1 µg/l | < 20 % * | Single value |
| Benzo(a)pyrene | <0,0005 mg/l below limit of quantification | 10 ng/l | cannot be assessed — the limit of quantification of the measurement is above the parametric value | Single value |
| Benzo(b)fluoranthene | <0,0000008 mg/l below limit of quantification | — | — | Single value |
| Benzo(ghi)perylene | <0,0000023 mg/l below limit of quantification | — | — | Single value |
| Benzo(k)fluoranthene | <0,0000009 mg/l below limit of quantification | — | — | Single value |
| Bisphenol A | <0,00009 mg/l below limit of quantification | 2.5 µg/l | < 4 % * | Single value |
| Boron | <0,13 mg/l below limit of quantification | 1 mg/l | < 13 % * | Single value |
| Bromate | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Bromodichloromethane | <0,002 mg/l below limit of quantification | — | — | Single value |
| Cadmium | <0,0002 mg/l below limit of quantification | 3 µg/l | < 7 % * | Single value |
| Chlorate | 0,023 mg/l | 70 µg/l | 33 % | Single value |
| Chlorite | <0,03 mg/l below limit of quantification | 0.2 mg/l | < 15 % * | Single value |
| Chromium | 0,00042 mg/l | 25 µg/l | 2 % | Single value |
| Copper | <0,1 mg/l below limit of quantification | 2 mg/l | < 5 % * | Single value |
| Cyanide | <0,002 mg/l below limit of quantification | 50 µg/l | < 4 % * | Single value |
| Dibromochloromethane | 0,002 mg/l | — | — | Single value |
| Fluoride | 0,2 mg/l | 1.5 mg/l | 13 % | Single value |
| Indeno(1,2,3-cd)pyrene | <0,0000023 mg/l below limit of quantification | — | — | Single value |
| Lead | 0,0002 mg/l | 10 µg/l | 2 % | Single value |
| Mercury | <0,0001 mg/l below limit of quantification | 1 µg/l | < 10 % * | Single value |
| Nickel | <0,001 mg/l below limit of quantification | 20 µg/l | < 5 % * | Single value |
| Nitrate | 26 mg/l | 50 mg/l | 52 % | Single value |
| Nitrite | <0,06 mg/l below limit of quantification | 0.5 mg/l | < 12 % * | Single value |
| Polycyclic aromatic hydrocarbons | <0,00003 mg/l below limit of quantification | 0.1 µg/l | < 30 % * | Single value |
| Selenium | <0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Tetrachloroethene | <0,0001 mg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene and Trichloroethene (sum) | <0,0001 mg/l below limit of quantification | 10 µg/l | < 1 % * | Single value |
| Tribromomethane (bromoform) | 0,005 mg/l | — | — | Single value |
| Trichloroethene | <0,0001 mg/l below limit of quantification | — | — | Single value |
| Trichloromethane (chloroform) | <0,002 mg/l below limit of quantification | — | — | Single value |
| Trihalomethanes — Total | 0,007 mg/l | 50 µg/l | 14 % | Single value |
| Uranium | 0,004 mg/l | 10 µg/l | 40 % | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Indicator parameters (17)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Aluminium | 0,004 mg/l | 0.2 mg/l | 2 % | Single value |
| Ammonium | <0,01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value |
| Calcite dissolution capacity | -43,2 mg/l | 5 mg/l CaCO3 | — | Single value |
| Chloride | 26 mg/l | 250 mg/l | 10 % | Single value |
| Coliform bacteria | 0 MPN/100 ml | 0/100 ml | — | Single value |
| Colony count 22 °C | 0 KBE/1 ml | ohne anormale Veränderung | — | Single value |
| Colony count 36 °C | 0 KBE/1 ml | ohne anormale Veränderung | — | Single value |
| Iron | <0,009 mg/l below limit of quantification | 0.2 mg/l | < 5 % * | Single value |
| Manganese | <0,003 mg/l below limit of quantification | 50 µg/l | < 6 % * | Single value |
| Odour | ohne | für den Verbraucher annehmbar | — | Single value |
| pH | 7,72 | 6,5–9,5 | — | Single value |
| Sodium | 8 mg/l | 200 mg/l | 4 % | Single value |
| Sulphate | 127 mg/l | 250 mg/l | 51 % | Single value |
| Taste | ohne | für den Verbraucher annehmbar | — | Single value |
| Temperature | 18,2 °C | — | — | Single value |
| Total organic carbon (TOC) | 0,68 mg/l | ohne anormale Veränderung | — | Single value |
| Turbidity | 0,8 FNU | 1 NTU | — | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Further parameters (6)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Acid capacity to pH 4.3 | 6,03 mmol/l | — | — | Single value |
| Base capacity to pH 8.2 | 0,23 mmol/l | — | — | Single value |
| Calcium | 113,8 mg/l | — | — | Single value |
| Magnesium | 44,4 mg/l | — | — | Single value |
| Potassium | 3,18 mg/l | — | — | Single value |
| Total hardness | 26,1 °dH | — | — | Single value |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://wasserapolda.de/wp-content/uploads/2024/12/Analysen-fuer-Homepage-Grossheringen.pdf · Probenahme 03.09.2025 · retrieved on 12/08/2026
Frequent questions about postcode 99518
- How hard is the water in Postcode 99518?
- Apoldaer Wasser GmbH publishes a total hardness of 33.2 °dH for the supply zone Bad Sulza (hardness range hard). The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: 12/2025, retrieved on 12/08/2026.
- How much nitrate is in the drinking water in Postcode 99518?
- Apoldaer Wasser GmbH publishes a nitrate value of 16,0 mg/l for the supply zone Bad Sulza. The statutory parametric value is 50 mg/l; the measured value represents 32 % of the parametric value. Basis: 12/2025, retrieved on 12/08/2026.
- Who supplies the drinking water in Postcode 99518?
- Apoldaer Wasser GmbH. The values shown here come from the supply zone Bad Sulza and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.
General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.