Skip to content
maunawai.info

Drinking water in 98716

For this postcode Wasser- und Abwasser Verband Ilmenau (WAVI) publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 9 underneath.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.8 °dH
Hardness range soft
Key values Fernwasser
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4,3 mg/l 50 mg/l
9 %
Single value · Fernwasser
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Fernwasser
Sulphate 5,8 mg/l 250 mg/l
2 %
Single value · Fernwasser
Sodium 5,2 mg/l 200 mg/l
3 %
Single value · Fernwasser
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Fernwasser
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Fernwasser
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Fernwasser

Chemical parameters (3)

Chemical parameters – Fernwasser
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,1 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Single value · Fernwasser
Nitrate 4,3 mg/l 50 mg/l
9 %
Single value · Fernwasser
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Fernwasser

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Fernwasser
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,02 mg/l 0.2 mg/l
10 %
Single value · Fernwasser
Ammonium 0,05 mg/l 0.5 mg/l
10 %
Single value · Fernwasser
Chloride 9,5 mg/l 250 mg/l
4 %
Single value · Fernwasser
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Fernwasser
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Fernwasser
Conductivity (25 °C) 173 µS/cm 2,790 µS/cm Single value · Fernwasser
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Fernwasser
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · Fernwasser
pH 8,1 6,5–9,5 Single value · Fernwasser
Sodium 5,2 mg/l 200 mg/l
3 %
Single value · Fernwasser
Sulphate 5,8 mg/l 250 mg/l
2 %
Single value · Fernwasser

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Fernwasser
Parameter Value Parametric value Share of the parametric value Reference
Calcium 24,7 mg/l Single value · Fernwasser
Magnesium 1,3 mg/l Single value · Fernwasser
Potassium 0,7 mg/l Single value · Fernwasser
Total hardness 0,68 mmol/l Single value · Fernwasser

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Show 9 more supply zones in this postcode

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3 °dH
Hardness range soft
Key values Gehren
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4,6 mg/l 50 mg/l
9 %
Single value · Gehren
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Gehren
Sulphate 14,0 mg/l 250 mg/l
6 %
Single value · Gehren
Sodium 2,2 mg/l 200 mg/l
1 %
Single value · Gehren
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Gehren
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Gehren
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Gehren

Chemical parameters (3)

Chemical parameters – Gehren
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,10 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Single value · Gehren
Nitrate 4,6 mg/l 50 mg/l
9 %
Single value · Gehren
Nitrite < 0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Gehren

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Gehren
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,03 mg/l 0.2 mg/l
15 %
Single value · Gehren
Ammonium 0,03 mg/l 0.5 mg/l
6 %
Single value · Gehren
Chloride 3,2 mg/l 250 mg/l
1 %
Single value · Gehren
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Gehren
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Gehren
Conductivity (25 °C) 164 µS/cm 2,790 µS/cm Single value · Gehren
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Gehren
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · Gehren
pH 8,2 6,5–9,5 Single value · Gehren
Sodium 2,2 mg/l 200 mg/l
1 %
Single value · Gehren
Sulphate 14,0 mg/l 250 mg/l
6 %
Single value · Gehren

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Gehren
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,6 mg/l Single value · Gehren
Magnesium 2,8 mg/l Single value · Gehren
Potassium 0,8 mg/l Single value · Gehren
Total hardness 0,54 mmol/l Single value · Gehren

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
8.6 °dH
Hardness range medium
Key values HB Nord
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 3,1 mg/l 50 mg/l
6 %
Single value · HB Nord
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · HB Nord
Sulphate 57,3 mg/l 250 mg/l
23 %
Single value · HB Nord
Sodium 8,3 mg/l 200 mg/l
4 %
Single value · HB Nord
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – HB Nord
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · HB Nord
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · HB Nord

Chemical parameters (3)

Chemical parameters – HB Nord
Parameter Value Parametric value Share of the parametric value Reference
Fluoride 0,13 mg/l 1.5 mg/l
9 %
Single value · HB Nord
Nitrate 3,1 mg/l 50 mg/l
6 %
Single value · HB Nord
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · HB Nord

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – HB Nord
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · HB Nord
Ammonium 0,06 mg/l 0.5 mg/l
12 %
Single value · HB Nord
Chloride 11,1 mg/l 250 mg/l
4 %
Single value · HB Nord
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · HB Nord
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · HB Nord
Conductivity (25 °C) 338 µS/cm 2,790 µS/cm Single value · HB Nord
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · HB Nord
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · HB Nord
pH 8,1 6,5–9,5 Single value · HB Nord
Sodium 8,3 mg/l 200 mg/l
4 %
Single value · HB Nord
Sulphate 57,3 mg/l 250 mg/l
23 %
Single value · HB Nord

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – HB Nord
Parameter Value Parametric value Share of the parametric value Reference
Calcium 35,3 mg/l Single value · HB Nord
Magnesium 13,8 mg/l Single value · HB Nord
Potassium 4 mg/l Single value · HB Nord
Total hardness 1,53 mmol/l Single value · HB Nord

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
8.8 °dH
Hardness range medium
Key values Hengelbach
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 1 mg/l 50 mg/l
2 %
Single value · Hengelbach
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Hengelbach
Sulphate 41,6 mg/l 250 mg/l
17 %
Single value · Hengelbach
Sodium 6,0 mg/l 200 mg/l
3 %
Single value · Hengelbach
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Hengelbach
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Hengelbach
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Hengelbach

Chemical parameters (3)

Chemical parameters – Hengelbach
Parameter Value Parametric value Share of the parametric value Reference
Fluoride 0,21 mg/l 1.5 mg/l
14 %
Single value · Hengelbach
Nitrate 1 mg/l 50 mg/l
2 %
Single value · Hengelbach
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Hengelbach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Hengelbach
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Hengelbach
Ammonium < 0,06 mg/l
below limit of quantification
0.5 mg/l
< 12 % *
Single value · Hengelbach
Chloride 16,2 mg/l 250 mg/l
6 %
Single value · Hengelbach
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Hengelbach
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Hengelbach
Conductivity (25 °C) 348 µS/cm 2,790 µS/cm Single value · Hengelbach
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Hengelbach
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · Hengelbach
pH 7,8 6,5–9,5 Single value · Hengelbach
Sodium 6,0 mg/l 200 mg/l
3 %
Single value · Hengelbach
Sulphate 41,6 mg/l 250 mg/l
17 %
Single value · Hengelbach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Hengelbach
Parameter Value Parametric value Share of the parametric value Reference
Calcium 39,6 mg/l Single value · Hengelbach
Magnesium 14,0 mg/l Single value · Hengelbach
Potassium 4,6 mg/l Single value · Hengelbach
Total hardness 1,57 mmol/l Single value · Hengelbach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
4.6 °dH
Hardness range soft
Key values Herschdorf Pennewitz
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4,4 mg/l 50 mg/l
9 %
Single value · Herschdorf - Pennewitz
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Herschdorf - Pennewitz
Sulphate 14 mg/l 250 mg/l
6 %
Single value · Herschdorf - Pennewitz
Sodium 2,2 mg/l 200 mg/l
1 %
Single value · Herschdorf - Pennewitz
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Herschdorf Pennewitz
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Herschdorf - Pennewitz
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Herschdorf - Pennewitz

Chemical parameters (3)

Chemical parameters – Herschdorf Pennewitz
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,10 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Single value · Herschdorf - Pennewitz
Nitrate 4,4 mg/l 50 mg/l
9 %
Single value · Herschdorf - Pennewitz
Nitrite < 0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Herschdorf - Pennewitz

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Herschdorf Pennewitz
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,04 mg/l 0.2 mg/l
20 %
Single value · Herschdorf - Pennewitz
Ammonium 0,11 mg/l 0.5 mg/l
22 %
Single value · Herschdorf - Pennewitz
Chloride 3,5 mg/l 250 mg/l
1 %
Single value · Herschdorf - Pennewitz
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Herschdorf - Pennewitz
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Herschdorf - Pennewitz
Conductivity (25 °C) 167 µS/cm 2,790 µS/cm Single value · Herschdorf - Pennewitz
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Herschdorf - Pennewitz
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · Herschdorf - Pennewitz
pH 8,5 6,5–9,5 Single value · Herschdorf - Pennewitz
Sodium 2,2 mg/l 200 mg/l
1 %
Single value · Herschdorf - Pennewitz
Sulphate 14 mg/l 250 mg/l
6 %
Single value · Herschdorf - Pennewitz

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Herschdorf Pennewitz
Parameter Value Parametric value Share of the parametric value Reference
Calcium 27,2 mg/l Single value · Herschdorf - Pennewitz
Magnesium 2,8 mg/l Single value · Herschdorf - Pennewitz
Potassium 0,9 mg/l Single value · Herschdorf - Pennewitz
Total hardness 0,82 mmol/l Single value · Herschdorf - Pennewitz

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
8.1 °dH
Hardness range soft
Key values Heyda
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 2,8 mg/l 50 mg/l
6 %
Single value · Heyda
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Heyda
Sulphate < 0,8 mg/l
below limit of quantification
250 mg/l
< 0.3 % *
Single value · Heyda
Sodium 7,6 mg/l 200 mg/l
4 %
Single value · Heyda

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Heyda
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Heyda
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Heyda

Chemical parameters (3)

Chemical parameters – Heyda
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,10 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Single value · Heyda
Nitrate 2,8 mg/l 50 mg/l
6 %
Single value · Heyda
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Heyda

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Heyda
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Heyda
Ammonium 0,04 mg/l 0.5 mg/l
8 %
Single value · Heyda
Chloride 10,0 mg/l 250 mg/l
4 %
Single value · Heyda
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Heyda
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Heyda
Conductivity (25 °C) 339 µS/cm 2,790 µS/cm Single value · Heyda
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Heyda
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · Heyda
pH 8,1 6,5–9,5 Single value · Heyda
Sodium 7,6 mg/l 200 mg/l
4 %
Single value · Heyda
Sulphate < 0,8 mg/l
below limit of quantification
250 mg/l
< 0.3 % *
Single value · Heyda

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Heyda
Parameter Value Parametric value Share of the parametric value Reference
Calcium 35,3 mg/l Single value · Heyda
Magnesium 14,4 mg/l Single value · Heyda
Potassium 4,1 mg/l Single value · Heyda
Total hardness 1,44 mmol/l Single value · Heyda

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
4.4 °dH
Hardness range soft
Key values Ilmenau Süd-Mitte
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 3,1 mg/l 50 mg/l
6 %
Single value · Ilmenau Süd-Mitte
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Ilmenau Süd-Mitte
Sulphate 57,3 mg/l 250 mg/l
23 %
Single value · Ilmenau Süd-Mitte
Sodium 8,3 mg/l 200 mg/l
4 %
Single value · Ilmenau Süd-Mitte
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Ilmenau Süd-Mitte
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Ilmenau Süd-Mitte
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Ilmenau Süd-Mitte

Chemical parameters (3)

Chemical parameters – Ilmenau Süd-Mitte
Parameter Value Parametric value Share of the parametric value Reference
Fluoride 0,13 mg/l 1.5 mg/l
9 %
Single value · Ilmenau Süd-Mitte
Nitrate 3,1 mg/l 50 mg/l
6 %
Single value · Ilmenau Süd-Mitte
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Ilmenau Süd-Mitte

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Ilmenau Süd-Mitte
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Ilmenau Süd-Mitte
Ammonium 0,05 mg/l 0.5 mg/l
10 %
Single value · Ilmenau Süd-Mitte
Chloride 11,1 mg/l 250 mg/l
4 %
Single value · Ilmenau Süd-Mitte
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Ilmenau Süd-Mitte
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Ilmenau Süd-Mitte
Conductivity (25 °C) 193 µS/cm 2,790 µS/cm Single value · Ilmenau Süd-Mitte
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Ilmenau Süd-Mitte
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · Ilmenau Süd-Mitte
pH 8,3 6,5–9,5 Single value · Ilmenau Süd-Mitte
Sodium 8,3 mg/l 200 mg/l
4 %
Single value · Ilmenau Süd-Mitte
Sulphate 57,3 mg/l 250 mg/l
23 %
Single value · Ilmenau Süd-Mitte

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Ilmenau Süd-Mitte
Parameter Value Parametric value Share of the parametric value Reference
Calcium 27,9 mg/l Single value · Ilmenau Süd-Mitte
Magnesium 2 mg/l Single value · Ilmenau Süd-Mitte
Potassium 0,9 mg/l Single value · Ilmenau Süd-Mitte
Total hardness 0,79 mmol/l Single value · Ilmenau Süd-Mitte

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
16.6 °dH
Hardness range hard
Key values Königsee
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 14,0 mg/l 50 mg/l
28 %
Single value · Königsee
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Königsee
Sulphate 95,3 mg/l 250 mg/l
38 %
Single value · Königsee
Sodium 14,1 mg/l 200 mg/l
7 %
Single value · Königsee
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Königsee
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Königsee
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Königsee

Chemical parameters (3)

Chemical parameters – Königsee
Parameter Value Parametric value Share of the parametric value Reference
Fluoride 0,13 mg/l 1.5 mg/l
9 %
Single value · Königsee
Nitrate 14,0 mg/l 50 mg/l
28 %
Single value · Königsee
Nitrite < 0,002 mg/l
below limit of quantification
0.5 mg/l
< 0.4 % *
Single value · Königsee

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Königsee
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,02 mg/l
below limit of quantification
0.2 mg/l
< 10 % *
Single value · Königsee
Ammonium < 0,04 mg/l
below limit of quantification
0.5 mg/l
< 8 % *
Single value · Königsee
Chloride 34,3 mg/l 250 mg/l
14 %
Single value · Königsee
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Königsee
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Königsee
Conductivity (25 °C) 645 µS/cm 2,790 µS/cm Single value · Königsee
Iron < 0,03 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Single value · Königsee
Manganese < 0,015 mg/l
below limit of quantification
50 µg/l
< 30 % *
Single value · Königsee
pH 7,35 6,5–9,5 Single value · Königsee
Sodium 14,1 mg/l 200 mg/l
7 %
Single value · Königsee
Sulphate 95,3 mg/l 250 mg/l
38 %
Single value · Königsee

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Königsee
Parameter Value Parametric value Share of the parametric value Reference
Calcium 90,5 mg/l Single value · Königsee
Magnesium 17,1 mg/l Single value · Königsee
Potassium 2,8 mg/l Single value · Königsee
Total hardness 2,958 mmol/l Single value · Königsee

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
2 °dH
Hardness range soft
Key values Neuwerk
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 11,0 mg/l 50 mg/l
22 %
Single value · Neuwerk
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Neuwerk
Sulphate 10,0 mg/l 250 mg/l
4 %
Single value · Neuwerk
Sodium 13,5 mg/l 200 mg/l
7 %
Single value · Neuwerk
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Neuwerk
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Neuwerk
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Neuwerk

Chemical parameters (3)

Chemical parameters – Neuwerk
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,10 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Single value · Neuwerk
Nitrate 11,0 mg/l 50 mg/l
22 %
Single value · Neuwerk
Nitrite < 0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Neuwerk

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Neuwerk
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,10 mg/l 0.2 mg/l
50 %
Single value · Neuwerk
Ammonium 0,06 mg/l 0.5 mg/l
12 %
Single value · Neuwerk
Chloride 2,2 mg/l 250 mg/l
0.9 %
Single value · Neuwerk
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Neuwerk
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Neuwerk
Conductivity (25 °C) 99 µS/cm 2,790 µS/cm Single value · Neuwerk
Iron 0,05 mg/l 0.2 mg/l
25 %
Single value · Neuwerk
Manganese 0,008 mg/l 50 µg/l
16 %
Single value · Neuwerk
pH 8,0 6,5–9,5 Single value · Neuwerk
Sodium 13,5 mg/l 200 mg/l
7 %
Single value · Neuwerk
Sulphate 10,0 mg/l 250 mg/l
4 %
Single value · Neuwerk

Further parameters (4)

Further parameters – Neuwerk
Parameter Value Parametric value Share of the parametric value Reference
Calcium 4,7 mg/l Single value · Neuwerk
Magnesium 1,4 mg/l Single value · Neuwerk
Potassium 1,7 mg/l Single value · Neuwerk
Total hardness 0,36 mmol/l Single value · Neuwerk

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3 °dH
Hardness range soft
Key values Schmiedefeld
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4,8 mg/l 50 mg/l
10 %
Single value · Schmiedefeld
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Schmiedefeld
Sulphate 84 mg/l 250 mg/l
34 %
Single value · Schmiedefeld
Sodium 7,2 mg/l 200 mg/l
4 %
Single value · Schmiedefeld
Show all recorded parameters (20 — most recent value per parameter)

Microbiology (2)

Microbiology – Schmiedefeld
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 pro 100 ml 0/100 ml Single value · Schmiedefeld
Intestinal enterococci 0 pro 100 ml 0/100 ml Single value · Schmiedefeld

Chemical parameters (3)

Chemical parameters – Schmiedefeld
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,10 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Single value · Schmiedefeld
Nitrate 4,8 mg/l 50 mg/l
10 %
Single value · Schmiedefeld
Nitrite < 0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · Schmiedefeld

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Schmiedefeld
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,02 mg/l 0.2 mg/l
10 %
Single value · Schmiedefeld
Ammonium 0,05 mg/l 0.5 mg/l
10 %
Single value · Schmiedefeld
Chloride 14 mg/l 250 mg/l
6 %
Single value · Schmiedefeld
Clostridium perfringens (including spores) 0 pro 100 ml 0/100 ml Single value · Schmiedefeld
Coliform bacteria 0 pro 100 ml 0/100 ml Single value · Schmiedefeld
Conductivity (25 °C) 172 µS/cm 2,790 µS/cm Single value · Schmiedefeld
Iron < 0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value · Schmiedefeld
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value · Schmiedefeld
pH 9,1 6,5–9,5 Single value · Schmiedefeld
Sodium 7,2 mg/l 200 mg/l
4 %
Single value · Schmiedefeld
Sulphate 84 mg/l 250 mg/l
34 %
Single value · Schmiedefeld

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Schmiedefeld
Parameter Value Parametric value Share of the parametric value Reference
Calcium 19,8 mg/l Single value · Schmiedefeld
Magnesium 1,2 mg/l Single value · Schmiedefeld
Potassium 2,4 mg/l Single value · Schmiedefeld
Total hardness 0,54 mmol/l Single value · Schmiedefeld

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Frequent questions about postcode 98716

How hard is the water in Postcode 98716?
Wasser- und Abwasser Verband Ilmenau (WAVI) publishes a total hardness of 0,68 mmol/l for the supply zone Fernwasser — that corresponds to 3.8 °dH. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 18/08/2026.
How much nitrate is in the drinking water in Postcode 98716?
Wasser- und Abwasser Verband Ilmenau (WAVI) publishes a nitrate value of 4,3 mg/l for the supply zone Fernwasser. The statutory parametric value is 50 mg/l; the measured value represents 9 % of the parametric value. Basis: Publication by the water supplier, retrieved on 18/08/2026.
Who supplies the drinking water in Postcode 98716?
Wasser- und Abwasser Verband Ilmenau (WAVI). The values shown here come from the supply zone Fernwasser and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.