Skip to content
maunawai.info

Drinking water in 98634

For this postcode Stadtwerke Meiningen GmbH publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 2 underneath.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.9 °dH
Hardness range 1
Key values Wasungen
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 3 mg/l 50 mg/l
6 %
Single value · Wasungen
Show all recorded parameters (4 — most recent value per parameter)

Chemical parameters (1)

Chemical parameters – Wasungen
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 3 mg/l 50 mg/l
6 %
Single value · Wasungen

Indicator parameters (1)

Indicator parameters – Wasungen
Parameter Value Parametric value Share of the parametric value Reference
pH 8,0 6,5–9,5 Single value · Wasungen

Further parameters (2)

Further parameters – Wasungen
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) 1 Single value · Wasungen
Total hardness 0,7 mmol/l Single value · Wasungen

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: meiningen-c2fd7fea.html · retrieved on 25/07/2026
Show 2 more supply zones in this postcode

Dreißigacker, Wasserturm (Reinwasser, Abg.)

Stadtwerke Meiningen GmbH

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4 °dH
Hardness range soft
Key values Dreißigacker, Wasserturm (Reinwasser, Abg.)
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l 0.1 µg/l
0 %
Single value
Nitrate 5,3 mg/l 50 mg/l
11 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Sulphate 6,4 mg/l 250 mg/l
3 %
Single value
Sodium 6,3 mg/l 200 mg/l
3 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (82 — most recent value per parameter)

Chemical parameters (49)

Chemical parameters – Dreißigacker, Wasserturm (Reinwasser, Abg.)
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0005 mg/l
below limit of quantification
3 µg/l
< 17 % *
Single value
Antimony <0,001 mg/l
below limit of quantification
5 µg/l
< 20 % *
Single value
Arsenic 0,001 mg/l 10 µg/l
10 %
Single value
Atrazine <0,000030 mg/l
below limit of quantification
Single value
Benzene <0,0003 mg/l
below limit of quantification
1 µg/l
< 30 % *
Single value
Benzo(a)pyrene <0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Benzo(b)fluoranthene <0,000003 mg/l
below limit of quantification
Single value
Benzo(ghi)perylene <0,000003 mg/l
below limit of quantification
Single value
Benzo(k)fluoranthene <0,000003 mg/l
below limit of quantification
Single value
Bisphenol A <0,0005 mg/l
below limit of quantification
2.5 µg/l
< 20 % *
Single value
Boron <0,01 mg/l
below limit of quantification
1 mg/l
< 1 % *
Single value
Bromate <0,0025 mg/l
below limit of quantification
10 µg/l
< 25 % *
Single value
Cadmium <0,0004 mg/l
below limit of quantification
3 µg/l
< 13 % *
Single value
Chlorate <0,020 mg/l
below limit of quantification
70 µg/l
< 29 % *
Single value
Chlorite <0,060 mg/l
below limit of quantification
0.2 mg/l
< 30 % *
Single value
Chlorotoluron <0,000030 mg/l
below limit of quantification
Single value
Chromium <0,001 mg/l
below limit of quantification
25 µg/l
< 4 % *
Single value
Copper <0,01 mg/l
below limit of quantification
2 mg/l
< 0.5 % *
Single value
Cyanazine <0,000030 mg/l
below limit of quantification
Single value
Cyanide <0,01 mg/l
below limit of quantification
50 µg/l
< 20 % *
Single value
Dibromoacetic acid <0,0030 mg/l
below limit of quantification
Single value
Dichloroacetic acid <0,0030 mg/l
below limit of quantification
Single value
Diuron <0,000030 mg/l
below limit of quantification
Single value
Fluoride 0,19 mg/l 1.5 mg/l
13 %
Single value
Hexazinone <0,000030 mg/l
below limit of quantification
Single value
Indeno(1,2,3-cd)pyrene <0,000003 mg/l
below limit of quantification
Single value
Isoproturon <0,000030 mg/l
below limit of quantification
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Mercury <0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Metazachlor <0,000030 mg/l
below limit of quantification
Single value
Methabenzthiazuron <0,000030 mg/l
below limit of quantification
Single value
Metobromuron <0,000030 mg/l
below limit of quantification
Single value
Metolachlor <0,000030 mg/l
below limit of quantification
Single value
Metoxuron <0,000030 mg/l
below limit of quantification
Single value
Monobromoacetic acid <0,0030 mg/l
below limit of quantification
Single value
Monochloroacetic acid <0,0030 mg/l
below limit of quantification
Single value
Nickel <0,001 mg/l
below limit of quantification
20 µg/l
< 5 % *
Single value
Nitrate 5,3 mg/l 50 mg/l
11 %
Single value
Nitrite <0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value
Sebuthylazine <0,000030 mg/l
below limit of quantification
Single value
Selenium 0,002 mg/l 10 µg/l
20 %
Single value
Simazine <0,000030 mg/l
below limit of quantification
Single value
Terbuthylazine <0,000030 mg/l
below limit of quantification
Single value
Tetrachloroethene <0,0005 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) <0,0005 mg/l
below limit of quantification
Single value
Trichloroacetic acid <0,0030 mg/l
below limit of quantification
Single value
Trichloroethene <0,0005 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) 0,0006 mg/l Single value
Uranium 0 mg/l 10 µg/l
0 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (20)

PFAS – Dreißigacker, Wasserturm (Reinwasser, Abg.)
Parameter Value Parametric value Share of the parametric value Reference
Perfluorobutane sulfonic acid (PFBS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorobutanoic acid (PFBA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorodecane sulfonic acid (PFDS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorodecanoic acid (PFDA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorododecane sulfonic acid (PFDoDS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorododecanoic acid (PFDoDA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluoroheptane sulfonic acid (PFHpS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluoroheptanoic acid (PFHpA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorohexane sulfonic acid (PFHxS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorohexanoic acid (PFHxA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorononane sulfonic acid (PFNS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorononanoic acid (PFNA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorooctanesulfonic acid (PFOS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluoropentanesulfonic acid (PFPeS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluoropentanoic acid (PFPeA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorotridecanesulfonic acid (PFTrDS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluorotridecanoic acid (PFTrDA) <0,0000015 mg/l
below limit of quantification
Single value
Perfluoroundecanesulfonic acid (PFUnDS) <0,0000015 mg/l
below limit of quantification
Single value
Perfluoroundecanoic acid (PFUnDA) <0,0000015 mg/l
below limit of quantification
Single value
Sum of PFAS 0 mg/l 0.1 µg/l
0 %
Single value

Indicator parameters (8)

Indicator parameters – Dreißigacker, Wasserturm (Reinwasser, Abg.)
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,03 mg/l 0.2 mg/l
15 %
Single value
Ammonium <0,02 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value
Chloride 11 mg/l 250 mg/l
4 %
Single value
Iron <0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value
pH 8,8 6,5–9,5 Single value
Sodium 6,3 mg/l 200 mg/l
3 %
Single value
Sulphate 6,4 mg/l 250 mg/l
3 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Treatment substances (1)

Treatment substances – Dreißigacker, Wasserturm (Reinwasser, Abg.)
Parameter Value Parametric value Share of the parametric value Reference
Free chlorine <0,04 mg/l
below limit of quantification
Single value

Further parameters (4)

Further parameters – Dreißigacker, Wasserturm (Reinwasser, Abg.)
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,6 mg/l Single value
Magnesium 1,4 mg/l Single value
Potassium 0,9 mg/l Single value
Total hardness 4,0 dH Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.stadtwerke-meiningen.de/dokumente/wasser/202607_Trinkwasser_Pruefbericht_Parameter_Gruppe_B.pdf · 30.06.2026 · 16.06.2026 - 30.06.2026 (Prüfzeitraum) · retrieved on 11/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values Meiningen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 KBE/100 ml 0/100 ml Single value
Show all recorded parameters (10 — most recent value per parameter)

Microbiology (2)

Microbiology – Meiningen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 KBE/100 ml 0/100 ml Single value
Intestinal enterococci 0 KBE/100 ml 0/100 ml Single value

Indicator parameters (7)

Indicator parameters – Meiningen
Parameter Value Parametric value Share of the parametric value Reference
Clostridium perfringens (including spores) 0 KBE/100 ml 0/100 ml Single value
Coliform bacteria 0 KBE/100 ml 0/100 ml Single value
Colour <0,1 1/m
below limit of quantification
0.5 m⁻¹ Single value
Odour o.B. für den Verbraucher annehmbar Single value
pH 8,0 6,5–9,5 Single value
Taste o.B. für den Verbraucher annehmbar Single value
Turbidity <0,10 NTU
below limit of quantification
1 NTU Single value

Treatment substances (1)

Treatment substances – Meiningen
Parameter Value Parametric value Share of the parametric value Reference
Free chlorine <0,04 mg/l
below limit of quantification
Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.stadtwerke-meiningen.de/dokumente/wasser/202607_Trinkwasser_Pruefbericht_Parameter_Gruppe_A.pdf · 11.02.2026 · 05.02.2026 - 09.02.2026 · retrieved on 11/07/2026

Frequent questions about postcode 98634

How hard is the water in Postcode 98634?
Stadtwerke Meiningen GmbH publishes a total hardness of 0,7 mmol/l for the supply zone Wasungen — that corresponds to 3.9 °dH. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 25/07/2026.
How much nitrate is in the drinking water in Postcode 98634?
Stadtwerke Meiningen GmbH publishes a nitrate value of 3 mg/l for the supply zone Wasungen. The statutory parametric value is 50 mg/l; the measured value represents 6 % of the parametric value. Basis: Publication by the water supplier, retrieved on 25/07/2026.
Who supplies the drinking water in Postcode 98634?
Stadtwerke Meiningen GmbH. The values shown here come from the supply zone Wasungen and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.