Drinking water in 88512
For this postcode Stadtwerke Mengen publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 6 underneath.
How to read the share of the parametric value
12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.
Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.
Ortsnetz Hundersingen, Querweg 5: Feuerwehrhaus
Stadtwerke MengenAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 03/06/2025. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.
Water hardness
17.6 °dH
Hardness range hard
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Nitrate | 14.5 mg/l | 50 mg/l | 29 % | Single value |
| Lead | 0.0007 mg/l | 10 µg/l | 7 % | Single value |
| Escherichia coli (E. coli) | 0 KBE/100ml | 0/100 ml | — | Single value |
| Sulphate | 17.9 mg/l | 250 mg/l | 7 % | Single value |
| Sodium | 11.3 mg/l | 200 mg/l | 6 % | Single value |
Show all recorded parameters (80 — most recent value per parameter)
Microbiology (2)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Escherichia coli (E. coli) | 0 KBE/100ml | 0/100 ml | — | Single value |
| Intestinal enterococci | 0 KBE/100ml | 0/100 ml | — | Single value |
Chemical parameters (47)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| 1,2-dichloroethane | <0.3 µg/l below limit of quantification | 3 µg/l | < 10 % * | Single value |
| 2,6-Dichlorobenzamide (BAM) | <0.02 µg/l below limit of quantification | — | — | Single value |
| Antimony | <0.001 mg/l below limit of quantification | 5 µg/l | < 20 % * | Single value |
| Arsenic | <0.0005 mg/l below limit of quantification | 10 µg/l | < 5 % * | Single value |
| Atrazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Benzene | <0.25 µg/l below limit of quantification | 1 µg/l | < 25 % * | Single value |
| Benzo(a)pyrene | <0.0025 µg/l below limit of quantification | 10 ng/l | < 25 % * | Single value |
| Benzo(b)fluoranthene | <0.010 µg/l below limit of quantification | — | — | Single value |
| Benzo(ghi)perylene | <0.020 µg/l below limit of quantification | — | — | Single value |
| Benzo(k)fluoranthene | <0.010 µg/l below limit of quantification | — | — | Single value |
| Bisphenol A | <0.01 µg/l below limit of quantification | 2.5 µg/l | < 0.4 % * | Single value |
| Boron | <0.01 mg/l below limit of quantification | 1 mg/l | < 1 % * | Single value |
| Bromate | - mg/l not determined | 10 µg/l | — | Single value |
| Bromodichloromethane | <0.1 µg/l below limit of quantification | — | — | Single value |
| Cadmium | <0.0001 mg/l below limit of quantification | 3 µg/l | < 3 % * | Single value |
| Chromium | <0.0005 mg/l below limit of quantification | 25 µg/l | < 2 % * | Single value |
| Copper | 0.013 mg/l | 2 mg/l | 0.7 % | Single value |
| Cyanide | <0.002 mg/l below limit of quantification | 50 µg/l | < 4 % * | Single value |
| Desethylatrazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Desethylterbuthylazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Desisopropylatrazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Dibromochloromethane | <0.1 µg/l below limit of quantification | — | — | Single value |
| Hexazinone | <0.02 µg/l below limit of quantification | — | — | Single value |
| Indeno(1,2,3-cd)pyrene | <0.010 µg/l below limit of quantification | — | — | Single value |
| Lead | 0.0007 mg/l | 10 µg/l | 7 % | Single value |
| Mercury | <0.0002 mg/l below limit of quantification | 1 µg/l | < 20 % * | Single value |
| Metazachlor | <0.02 µg/l below limit of quantification | — | — | Single value |
| Metolachlor | <0.02 µg/l below limit of quantification | — | — | Single value |
| Nickel | <0.001 mg/l below limit of quantification | 20 µg/l | < 5 % * | Single value |
| Nitrate | 14.5 mg/l | 50 mg/l | 29 % | Single value |
| Nitrate/50 + Nitrite/3 | 0.29 mg/l | 1 | — | Single value |
| Nitrite | <0.01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value |
| Pesticides — Total | n.n. µg/l not detectable | 0.5 µg/l | — | Single value |
| Polycyclic aromatic hydrocarbons | n.n. µg/l not detectable | 0.1 µg/l | — | Single value |
| Propazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Sebuthylazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Selenium | <0.001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Simazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Terbuthylazine | <0.02 µg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene | <0.1 µg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene and Trichloroethene (sum) | n.n. µg/l not detectable | 10 µg/l | — | Single value |
| Tribromomethane (bromoform) | <0.1 µg/l below limit of quantification | — | — | Single value |
| Trichloroethene | <0.1 µg/l below limit of quantification | — | — | Single value |
| Trichloromethane (chloroform) | <0.1 µg/l below limit of quantification | — | — | Single value |
| Trihalomethanes — Total | n.n. µg/l not detectable | 50 µg/l | — | Single value |
| Uranium | 0.0025 mg/l | 10 µg/l | 25 % | Single value |
| Vinyl chloride | <0.25 µg/l below limit of quantification | 0.5 µg/l | < 50 % * | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Indicator parameters (19)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Aluminium | <0.005 mg/l below limit of quantification | 0.2 mg/l | < 3 % * | Single value |
| Ammonium | <0.01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value |
| Calcite dissolution capacity | -36 mg/l | 5 mg/l CaCO3 | — | Single value |
| Chloride | 15.5 mg/l | 250 mg/l | 6 % | Single value |
| Coliform bacteria | 0 KBE/100ml | 0/100 ml | — | Single value |
| Colony count 22 °C | 1 KBE/ml | ohne anormale Veränderung | — | Single value |
| Colony count 36 °C | 0 KBE/ml | ohne anormale Veränderung | — | Single value |
| Colour | <0.05 m-1 below limit of quantification | 0.5 m⁻¹ | — | Single value |
| Conductivity (25 °C) | 642 µS/cm | 2,790 µS/cm | — | Single value |
| Iron | <0.01 mg/l below limit of quantification | 0.2 mg/l | < 5 % * | Single value |
| Manganese | <0.0025 mg/l below limit of quantification | 50 µg/l | < 5 % * | Single value |
| Odour | o.B. - | für den Verbraucher annehmbar | — | Single value |
| pH | 7.19 - | 6,5–9,5 | — | Single value |
| Sodium | 11.3 mg/l | 200 mg/l | 6 % | Single value |
| Sulphate | 17.9 mg/l | 250 mg/l | 7 % | Single value |
| Taste | - - not determined | für den Verbraucher annehmbar | — | Single value |
| Temperature | 14.6 °C | — | — | Single value |
| Total organic carbon (TOC) | 1.4 mg/l | ohne anormale Veränderung | — | Single value |
| Turbidity | 0.13 NTU | 1 NTU | — | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Further parameters (12)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Calcium | 103 mg/l | — | — | Single value |
| Carbonate hardness | 16.8 °dH | — | — | Single value |
| Copper quotient | 32.25 | — | — | Single value |
| Free carbon dioxide | 20.0 mg/l | — | — | Single value |
| Magnesium | 13.8 mg/l | — | — | Single value |
| Pitting corrosion quotient S1 | 0.17 | — | — | Single value |
| Potassium | 1.3 mg/l | — | — | Single value |
| Saturation index | +0,41 - | — | — | Single value |
| Spectral absorption coefficient 254 nm (SAC 254) | 2.7 m-1 | — | — | Single value |
| Sum of alkaline earth metals | 3.1 mmol/l | — | — | Single value |
| Total hardness | 17.6 °dH | — | — | Single value |
| Trickling quotient | 3.46 | — | — | Single value |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://www.mengen.de/sw-wAssets/docs/wasser/analysen/02_analyse-beuren.pdf · 17. 7. 2025 · 03.06.2025 · retrieved on 08/07/2026
Show 6 more supply zones in this postcode
Rulfingen / Feuerwehrhaus
Stadtwerke MengenAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
Water hardness
19.7 °dH
Hardness range hart
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Sum of PFAS | 0,0000047 mg/l | 0.1 µg/l | 5 % | Single value |
| Nitrate | 21 mg/l | 50 mg/l | 42 % | Single value |
| Lead | 0,002 mg/l | 10 µg/l | 20 % | Single value |
| Sulphate | 22 mg/l | 250 mg/l | 9 % | Single value |
| Sodium | 19,6 mg/l | 200 mg/l | 10 % | Single value |
Show all recorded parameters (87 — most recent value per parameter)
Chemical parameters (42)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| 1,2-dichloroethane | < 0,0005 mg/l below limit of quantification | 3 µg/l | < 17 % * | Single value |
| Antimony | < 0,001 mg/l below limit of quantification | 5 µg/l | < 20 % * | Single value |
| Arsenic | < 0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Atrazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Benzene | < 0,00025 mg/l below limit of quantification | 1 µg/l | < 25 % * | Single value |
| Benzo(a)pyrene | < 0,000001 mg/l below limit of quantification | 10 ng/l | < 10 % * | Single value |
| Benzo(b)fluoranthene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Benzo(ghi)perylene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Benzo(k)fluoranthene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Bisphenol A | < 0,00001 mg/l below limit of quantification | 2.5 µg/l | < 0.4 % * | Single value |
| Boron | 0,02 mg/l | 1 mg/l | 2 % | Single value |
| Bromate | < 0,0025 mg/l below limit of quantification | 10 µg/l | < 25 % * | Single value |
| Bromodichloromethane | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Cadmium | < 0,0001 mg/l below limit of quantification | 3 µg/l | < 3 % * | Single value |
| Chromium | 0,0006 mg/l | 25 µg/l | 2 % | Single value |
| Copper | 0,051 mg/l | 2 mg/l | 3 % | Single value |
| Cyanide | < 0,005 mg/l below limit of quantification | 50 µg/l | < 10 % * | Single value |
| Desethylatrazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Desethylterbuthylazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Desisopropylatrazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Dibromochloromethane | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Fluoride | 0,08 mg/l | 1.5 mg/l | 5 % | Single value |
| Indeno(1,2,3-cd)pyrene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Lead | 0,002 mg/l | 10 µg/l | 20 % | Single value |
| Mercury | < 0,0001 mg/l below limit of quantification | 1 µg/l | < 10 % * | Single value |
| Metazachlor | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Metolachlor | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Nickel | < 0,001 mg/l below limit of quantification | 20 µg/l | < 5 % * | Single value |
| Nitrate | 21 mg/l | 50 mg/l | 42 % | Single value |
| Nitrite | < 0,01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value |
| Pesticides — Total | (n. b.) mg/l not determined | 0.5 µg/l | — | Single value |
| Polycyclic aromatic hydrocarbons | (n. b.) mg/l not determined | 0.1 µg/l | — | Single value |
| Selenium | 0,001 mg/l | 10 µg/l | 10 % | Single value |
| Simazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Terbuthylazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene and Trichloroethene (sum) | (n. b.) mg/l not determined | 10 µg/l | — | Single value |
| Tribromomethane (bromoform) | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Trichloroethene | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Trichloromethane (chloroform) | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Trihalomethanes — Total | (n. b.) mg/l not determined | 50 µg/l | — | Single value |
| Uranium | 0,0070 mg/l | 10 µg/l | 70 % | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
PFAS (18)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Perfluorobutane sulfonic acid (PFBS) | 0,0023 µg/l | — | — | Single value |
| Perfluorobutanoic acid (PFBA) | 0,0024 µg/l | — | — | Single value |
| Perfluorodecane sulfonic acid (PFDS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorododecanoic acid (PFDoDA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoroheptane sulfonic acid (PFHpS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoroheptanoic acid (PFHpA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorohexane sulfonic acid (PFHxS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorohexanoic acid (PFHxA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorononane sulfonic acid (PFNS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorononanoic acid (PFNA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorooctanesulfonic acid (PFOS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorooctanoic acid (PFOA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoropentanesulfonic acid (PFPeS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoropentanoic acid (PFPeA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorotridecanesulfonic acid (PFTrDS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoroundecanoic acid (PFUnDA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Sum of 4 PFAS | (n. b.) mg/l not determined | — | — | Single value |
| Sum of PFAS | 0,0000047 mg/l | 0.1 µg/l | 5 % | Single value |
Indicator parameters (10)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Aluminium | < 0,005 mg/l below limit of quantification | 0.2 mg/l | < 3 % * | Single value |
| Ammonium | < 0,01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value |
| Calcite dissolution capacity | -24 mg/l | 5 mg/l CaCO3 | — | Single value |
| Chloride | 30 mg/l | 250 mg/l | 12 % | Single value |
| Iron | < 0,005 mg/l below limit of quantification | 0.2 mg/l | < 3 % * | Single value |
| Manganese | < 0,001 mg/l below limit of quantification | 50 µg/l | < 2 % * | Single value |
| Sodium | 19,6 mg/l | 200 mg/l | 10 % | Single value |
| Sulphate | 22 mg/l | 250 mg/l | 9 % | Single value |
| Temperature | 17,8 °C | — | — | Single value |
| Total organic carbon (TOC) | 1,3 mg/l | ohne anormale Veränderung | — | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Treatment substances (1)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Free chlorine | < 0,05 mg/l below limit of quantification | — | — | Single value |
Further parameters (16)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Acid capacity to pH 4.3 | 6,6 mmol/l | — | — | Single value |
| Acid capacity to pH 8.2 | < 0,1 mmol/l below limit of quantification | — | — | Single value |
| Base capacity to pH 8.2 | 1,03 mmol/l | — | — | Single value |
| Calcium | 116 mg/l | — | — | Single value |
| Carbonate hardness | 3,31 mmol/l | — | — | Single value |
| Copper quotient | 28,5 | — | — | Single value |
| Hardness range (WRMG) | hart | — | — | Single value |
| Hydrogen carbonate | 401 mg/l | — | — | Single value |
| Magnesium | 15,1 mg/l | — | — | Single value |
| Oxygen | 7,8 mg/l | — | — | Single value |
| Phosphate | < 0,6 mg/l below limit of quantification | — | — | Single value |
| Pitting corrosion quotient S1 | 0,252 | — | — | Single value |
| Potassium | 5,6 mg/l | — | — | Single value |
| Saturation index | 0,18 | — | — | Single value |
| Total hardness | 3,52 mmol/l | — | — | Single value |
| Trickling quotient | 3,86 | — | — | Single value |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://www.mengen.de/sw-wAssets/docs/wasser/analysen/01_02_analyse-mengen-teil2.pdf · 25.06.2026 · Probenahmedatum 11.06.2026, Prüfzeitraum 11.06.2026 - 24.06.2026 · retrieved on 08/07/2026
Entnahmestelle Teis / Entnahmehahn, Eichhausgasse 8 (Bauhof) / Werkstatt
Stadtwerke MengenAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
Water hardness
19 °dH
Hardness range hart
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Sum of PFAS | 0,0000075 mg/l | 0.1 µg/l | 8 % | Single value |
| Nitrate | 15 mg/l | 50 mg/l | 30 % | Single value |
| Lead | < 0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Sulphate | 21 mg/l | 250 mg/l | 8 % | Single value |
| Sodium | 19,7 mg/l | 200 mg/l | 10 % | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Show all recorded parameters (84 — most recent value per parameter)
Chemical parameters (42)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| 1,2-dichloroethane | < 0,0005 mg/l below limit of quantification | 3 µg/l | < 17 % * | Single value |
| Antimony | < 0,001 mg/l below limit of quantification | 5 µg/l | < 20 % * | Single value |
| Arsenic | < 0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Atrazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Benzene | < 0,00025 mg/l below limit of quantification | 1 µg/l | < 25 % * | Single value |
| Benzo(a)pyrene | < 0,000001 mg/l below limit of quantification | 10 ng/l | < 10 % * | Single value |
| Benzo(b)fluoranthene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Benzo(ghi)perylene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Benzo(k)fluoranthene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Bisphenol A | < 0,00001 mg/l below limit of quantification | 2.5 µg/l | < 0.4 % * | Single value |
| Boron | < 0,02 mg/l below limit of quantification | 1 mg/l | < 2 % * | Single value |
| Bromate | < 0,0025 mg/l below limit of quantification | 10 µg/l | < 25 % * | Single value |
| Bromodichloromethane | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Cadmium | < 0,0001 mg/l below limit of quantification | 3 µg/l | < 3 % * | Single value |
| Chromium | < 0,0005 mg/l below limit of quantification | 25 µg/l | < 2 % * | Single value |
| Copper | 0,018 mg/l | 2 mg/l | 0.9 % | Single value |
| Cyanide | < 0,005 mg/l below limit of quantification | 50 µg/l | < 10 % * | Single value |
| Desethylatrazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Desethylterbuthylazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Desisopropylatrazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Dibromochloromethane | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Fluoride | 0,08 mg/l | 1.5 mg/l | 5 % | Single value |
| Indeno(1,2,3-cd)pyrene | < 0,000001 mg/l below limit of quantification | — | — | Single value |
| Lead | < 0,001 mg/l below limit of quantification | 10 µg/l | < 10 % * | Single value |
| Mercury | < 0,0001 mg/l below limit of quantification | 1 µg/l | < 10 % * | Single value |
| Metazachlor | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Metolachlor | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Nickel | < 0,001 mg/l below limit of quantification | 20 µg/l | < 5 % * | Single value |
| Nitrate | 15 mg/l | 50 mg/l | 30 % | Single value |
| Nitrite | < 0,01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value |
| Pesticides — Total | (n. b.) mg/l not determined | 0.5 µg/l | — | Single value |
| Polycyclic aromatic hydrocarbons | (n. b.) mg/l not determined | 0.1 µg/l | — | Single value |
| Selenium | 0,001 mg/l | 10 µg/l | 10 % | Single value |
| Simazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Terbuthylazine | < 0,000025 mg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Tetrachloroethene and Trichloroethene (sum) | (n. b.) mg/l not determined | 10 µg/l | — | Single value |
| Tribromomethane (bromoform) | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Trichloroethene | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Trichloromethane (chloroform) | < 0,0005 mg/l below limit of quantification | — | — | Single value |
| Trihalomethanes — Total | (n. b.) mg/l not determined | 50 µg/l | — | Single value |
| Uranium | 0,0067 mg/l | 10 µg/l | 67 % | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
PFAS (18)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Perfluorobutane sulfonic acid (PFBS) | 0,0025 µg/l | — | — | Single value |
| Perfluorobutanoic acid (PFBA) | 0,0039 µg/l | — | — | Single value |
| Perfluorodecane sulfonic acid (PFDS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorododecanoic acid (PFDoDA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoroheptane sulfonic acid (PFHpS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoroheptanoic acid (PFHpA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorohexane sulfonic acid (PFHxS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorohexanoic acid (PFHxA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorononane sulfonic acid (PFNS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorononanoic acid (PFNA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorooctanesulfonic acid (PFOS) | 0,0011 µg/l | — | — | Single value |
| Perfluorooctanoic acid (PFOA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoropentanesulfonic acid (PFPeS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoropentanoic acid (PFPeA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluorotridecanesulfonic acid (PFTrDS) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Perfluoroundecanoic acid (PFUnDA) | < 0,0010 µg/l below limit of quantification | — | — | Single value |
| Sum of 4 PFAS | 0,0000011 mg/l | — | — | Single value |
| Sum of PFAS | 0,0000075 mg/l | 0.1 µg/l | 8 % | Single value |
Indicator parameters (9)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Aluminium | < 0,005 mg/l below limit of quantification | 0.2 mg/l | < 3 % * | Single value |
| Ammonium | < 0,01 mg/l below limit of quantification | 0.5 mg/l | < 2 % * | Single value |
| Calcite dissolution capacity | -38 mg/l | 5 mg/l CaCO3 | — | Single value |
| Chloride | 30 mg/l | 250 mg/l | 12 % | Single value |
| Iron | < 0,005 mg/l below limit of quantification | 0.2 mg/l | < 3 % * | Single value |
| Manganese | < 0,001 mg/l below limit of quantification | 50 µg/l | < 2 % * | Single value |
| Sodium | 19,7 mg/l | 200 mg/l | 10 % | Single value |
| Sulphate | 21 mg/l | 250 mg/l | 8 % | Single value |
| Total organic carbon (TOC) | 1,3 mg/l | ohne anormale Veränderung | — | Single value |
* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.
Further parameters (15)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Acid capacity to pH 4.3 | 6,6 mmol/l | — | — | Single value |
| Acid capacity to pH 8.2 | < 0,1 mmol/l below limit of quantification | — | — | Single value |
| Base capacity to pH 8.2 | 0,533 mmol/l | — | — | Single value |
| Calcium | 113 mg/l | — | — | Single value |
| Carbonate hardness | 3,29 mmol/l | — | — | Single value |
| Copper quotient | 30,7 | — | — | Single value |
| Hardness range (WRMG) | hart | — | — | Single value |
| Hydrogen carbonate | 398 mg/l | — | — | Single value |
| Magnesium | 13,8 mg/l | — | — | Single value |
| Phosphate | < 0,6 mg/l below limit of quantification | — | — | Single value |
| Pitting corrosion quotient S1 | 0,233 | — | — | Single value |
| Potassium | 5,2 mg/l | — | — | Single value |
| Saturation index | 0,37 | — | — | Single value |
| Total hardness | 3,39 mmol/l | — | — | Single value |
| Trickling quotient | 5,20 | — | — | Single value |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://www.mengen.de/sw-wAssets/docs/wasser/analysen/01_01_analyse-mengen-teil1.pdf · 27.02.2026 · Probenahme 19.02.2026, Prüfzeitraum 19.02.2026 - 27.02.2026 · retrieved on 08/07/2026
Vor-Ort-Messung
Stadtwerke MengenAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
No core values are available for this zone yet.
Show all recorded parameters (5 — most recent value per parameter)
Indicator parameters (3)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Conductivity (25 °C) | 745 µS/cm | 2,790 µS/cm | — | Single value · Vor-Ort-Messung |
| pH | 7,21 | 6,5–9,5 | — | Single value · Vor-Ort-Messung |
| Temperature | 6,5 °C | — | — | Single value · Vor-Ort-Messung |
Treatment substances (1)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Free chlorine | < 0,05 mg/l below limit of quantification | — | — | Single value · Vor-Ort-Messung |
Further parameters (1)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Oxygen | 11,2 mg/l | — | — | Single value · Vor-Ort-Messung |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://www.mengen.de/sw-wAssets/docs/wasser/analysen/01_01_analyse-mengen-teil1.pdf · 27.02.2026 · Probenahme 19.02.2026, Prüfzeitraum 19.02.2026 - 27.02.2026 · retrieved on 08/07/2026
Labor
Stadtwerke MengenAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
No core values are available for this zone yet.
Show all recorded parameters (2 — most recent value per parameter)
Indicator parameters (2)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Conductivity (25 °C) | 742 µS/cm | 2,790 µS/cm | — | Single value · Labor |
| pH | 7,39 | 6,5–9,5 | — | Single value · Labor |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://www.mengen.de/sw-wAssets/docs/wasser/analysen/01_02_analyse-mengen-teil2.pdf · 25.06.2026 · Probenahmedatum 11.06.2026, Prüfzeitraum 11.06.2026 - 24.06.2026 · retrieved on 08/07/2026
Labormessung
Stadtwerke MengenAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
No core values are available for this zone yet.
Show all recorded parameters (2 — most recent value per parameter)
Indicator parameters (2)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Conductivity (25 °C) | 727 µS/cm | 2,790 µS/cm | — | Single value · Labormessung |
| pH | 7,43 | 6,5–9,5 | — | Single value · Labormessung |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://www.mengen.de/sw-wAssets/docs/wasser/analysen/01_01_analyse-mengen-teil1.pdf · 27.02.2026 · Probenahme 19.02.2026, Prüfzeitraum 19.02.2026 - 27.02.2026 · retrieved on 08/07/2026
Vor-Ort
Stadtwerke MengenAssigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.
No core values are available for this zone yet.
Show all recorded parameters (2 — most recent value per parameter)
Indicator parameters (2)
| Parameter | Value | Parametric value | Share of the parametric value | Reference |
|---|---|---|---|---|
| Conductivity (25 °C) | 589 µS/cm | 2,790 µS/cm | — | Single value · Vor-Ort |
| pH | 7,14 | 6,5–9,5 | — | Single value · Vor-Ort |
Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.
Source: https://www.mengen.de/sw-wAssets/docs/wasser/analysen/01_02_analyse-mengen-teil2.pdf · 25.06.2026 · Probenahmedatum 11.06.2026, Prüfzeitraum 11.06.2026 - 24.06.2026 · retrieved on 08/07/2026
Frequent questions about postcode 88512
- How hard is the water in Postcode 88512?
- Stadtwerke Mengen publishes a total hardness of 17.6 °dH for the supply zone Ortsnetz Hundersingen, Querweg 5: Feuerwehrhaus (hardness range hard). The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: 17. 7. 2025, retrieved on 08/07/2026.
- How much nitrate is in the drinking water in Postcode 88512?
- Stadtwerke Mengen publishes a nitrate value of 14.5 mg/l for the supply zone Ortsnetz Hundersingen, Querweg 5: Feuerwehrhaus. The statutory parametric value is 50 mg/l; the measured value represents 29 % of the parametric value. Basis: 17. 7. 2025, retrieved on 08/07/2026.
- Who supplies the drinking water in Postcode 88512?
- Stadtwerke Mengen. The values shown here come from the supply zone Ortsnetz Hundersingen, Querweg 5: Feuerwehrhaus and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.
General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.