Skip to content
maunawai.info

Drinking water in 58553

For this postcode the responsible water supplier publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 11 underneath. The water supplier publishes 1 further local networks that cannot be clearly assigned to this postcode — they are listed on the water supplier page.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Brunnen Büchermühle TW

Stadtwerke Halver GmbH

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2023. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Key values Brunnen Büchermühle TW
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 16,9 mg / l 50 mg/l — Mean · Brunnen Büchermühle TW
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · Brunnen Büchermühle TW
Sulphate 16 mg / l 250 mg/l — Mean · Brunnen Büchermühle TW
Sodium 6,8 mg / l 200 mg/l — Mean · Brunnen Büchermühle TW
Show all recorded parameters (24 — most recent value per parameter)

Microbiology (1)

Microbiology – Brunnen Büchermühle TW
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 / 100 ml 0/100 ml — Mean · Brunnen Büchermühle TW

Chemical parameters (5)

Chemical parameters – Brunnen Büchermühle TW
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,05 mg / l
below limit of quantification
 1.5 mg/l — Mean · Brunnen Büchermühle TW
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · Brunnen Büchermühle TW
Nitrate 16,9 mg / l 50 mg/l — Mean · Brunnen Büchermühle TW
Nitrite <0,01 mg / l
below limit of quantification
 0.5 mg/l — Mean · Brunnen Büchermühle TW
Uranium <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · Brunnen Büchermühle TW

Indicator parameters (12)

Indicator parameters – Brunnen Büchermühle TW
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,01 mg / l
below limit of quantification
 0.2 mg/l — Mean · Brunnen Büchermühle TW
Ammonium <0,01 mg / l
below limit of quantification
 0.5 mg/l — Mean · Brunnen Büchermühle TW
Chloride 10 mg / l 250 mg/l — Mean · Brunnen Büchermühle TW
Clostridium perfringens (including spores) 0 / 100 ml 0/100 ml — Mean · Brunnen Büchermühle TW
Iron <0,01 mg / l
below limit of quantification
 0.2 mg/l — Mean · Brunnen Büchermühle TW
Manganese <0,01 mg / l
below limit of quantification
 50 µg/l — Mean · Brunnen Büchermühle TW
Odour ohne für den Verbraucher annehmbar — Mean · Brunnen Büchermühle TW
Sodium 6,8 mg / l 200 mg/l — Mean · Brunnen Büchermühle TW
Sulphate 16 mg / l 250 mg/l — Mean · Brunnen Büchermühle TW
Temperature 10,4 °C — — Mean · Brunnen Büchermühle TW
Total organic carbon (TOC) 0,4 mg / l ohne anormale Veränderung — Mean · Brunnen Büchermühle TW
Turbidity 0,12 FNU 1 NTU — Mean · Brunnen Büchermühle TW

Further parameters (6)

Further parameters – Brunnen Büchermühle TW
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 1,78 mmol / l — — Mean · Brunnen Büchermühle TW
Base capacity to pH 8.2 0,45 mmol / l — — Mean · Brunnen Büchermühle TW
Calcium 37,2 mg / l — — Mean · Brunnen Büchermühle TW
Magnesium 6,2 mg / l — — Mean · Brunnen Büchermühle TW
Potassium 0,8 mg / l — — Mean · Brunnen Büchermühle TW
Sum of alkaline earth metals 6,1 °dH — — Mean · Brunnen Büchermühle TW

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.stadtwerke-halver.de/wasser.html · Jahresmittelwerte 2023 · retrieved on 11/07/2026
Show 11 more supply zones in this postcode

Brunnen Ennepe TW

Stadtwerke Halver GmbH

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2023. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Key values Brunnen Ennepe TW
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 20,6 mg / l 50 mg/l — Mean · Brunnen Ennepe TW
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · Brunnen Ennepe TW
Sulphate 18 mg / l 250 mg/l — Mean · Brunnen Ennepe TW
Sodium 16,9 mg / l 200 mg/l — Mean · Brunnen Ennepe TW
Show all recorded parameters (24 — most recent value per parameter)

Microbiology (1)

Microbiology – Brunnen Ennepe TW
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 / 100 ml 0/100 ml — Mean · Brunnen Ennepe TW

Chemical parameters (5)

Chemical parameters – Brunnen Ennepe TW
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,05 mg / l
below limit of quantification
 1.5 mg/l — Mean · Brunnen Ennepe TW
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · Brunnen Ennepe TW
Nitrate 20,6 mg / l 50 mg/l — Mean · Brunnen Ennepe TW
Nitrite <0,01 mg / l
below limit of quantification
 0.5 mg/l — Mean · Brunnen Ennepe TW
Uranium <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · Brunnen Ennepe TW

Indicator parameters (12)

Indicator parameters – Brunnen Ennepe TW
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,01 mg / l
below limit of quantification
 0.2 mg/l — Mean · Brunnen Ennepe TW
Ammonium <0,01 mg / l
below limit of quantification
 0.5 mg/l — Mean · Brunnen Ennepe TW
Chloride 31 mg / l 250 mg/l — Mean · Brunnen Ennepe TW
Clostridium perfringens (including spores) 0 / 100 ml 0/100 ml — Mean · Brunnen Ennepe TW
Iron <0,01 mg / l
below limit of quantification
 0.2 mg/l — Mean · Brunnen Ennepe TW
Manganese <0,01 mg / l
below limit of quantification
 50 µg/l — Mean · Brunnen Ennepe TW
Odour ohne für den Verbraucher annehmbar — Mean · Brunnen Ennepe TW
Sodium 16,9 mg / l 200 mg/l — Mean · Brunnen Ennepe TW
Sulphate 18 mg / l 250 mg/l — Mean · Brunnen Ennepe TW
Temperature 10,6 °C — — Mean · Brunnen Ennepe TW
Total organic carbon (TOC) 0,4 mg / l ohne anormale Veränderung — Mean · Brunnen Ennepe TW
Turbidity 0,28 FNU 1 NTU — Mean · Brunnen Ennepe TW

Further parameters (6)

Further parameters – Brunnen Ennepe TW
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 2,79 mmol / l — — Mean · Brunnen Ennepe TW
Base capacity to pH 8.2 0,25 mmol / l — — Mean · Brunnen Ennepe TW
Calcium 62,7 mg / l — — Mean · Brunnen Ennepe TW
Magnesium 5,7 mg / l — — Mean · Brunnen Ennepe TW
Potassium 1,0 mg / l — — Mean · Brunnen Ennepe TW
Sum of alkaline earth metals 9,6 °dH — — Mean · Brunnen Ennepe TW

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.stadtwerke-halver.de/wasser.html · Jahresmittelwerte 2023 · retrieved on 11/07/2026

WW Jubach Trinkw

Stadtwerke Halver GmbH

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2023. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Key values WW Jubach Trinkw
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 18,0 mg / l 50 mg/l — Mean · WW Jubach Trinkw
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · WW Jubach Trinkw
Sulphate 9 mg / l 250 mg/l — Mean · WW Jubach Trinkw
Sodium 5,4 mg / l 200 mg/l — Mean · WW Jubach Trinkw
Show all recorded parameters (24 — most recent value per parameter)

Microbiology (1)

Microbiology – WW Jubach Trinkw
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 / 100 ml 0/100 ml — Mean · WW Jubach Trinkw

Chemical parameters (5)

Chemical parameters – WW Jubach Trinkw
Parameter Value Parametric value Share of the parametric value Reference
Fluoride <0,05 mg / l
below limit of quantification
 1.5 mg/l — Mean · WW Jubach Trinkw
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · WW Jubach Trinkw
Nitrate 18,0 mg / l 50 mg/l — Mean · WW Jubach Trinkw
Nitrite <0,01 mg / l
below limit of quantification
 0.5 mg/l — Mean · WW Jubach Trinkw
Uranium <0,001 mg / l
below limit of quantification
 10 µg/l — Mean · WW Jubach Trinkw

Indicator parameters (12)

Indicator parameters – WW Jubach Trinkw
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,04 mg / l 0.2 mg/l — Mean · WW Jubach Trinkw
Ammonium <0,01 mg / l
below limit of quantification
 0.5 mg/l — Mean · WW Jubach Trinkw
Chloride 8 mg / l 250 mg/l — Mean · WW Jubach Trinkw
Clostridium perfringens (including spores) 0 / 100 ml 0/100 ml — Mean · WW Jubach Trinkw
Iron <0,01 mg / l
below limit of quantification
 0.2 mg/l — Mean · WW Jubach Trinkw
Manganese <0,01 mg / l
below limit of quantification
 50 µg/l — Mean · WW Jubach Trinkw
Odour ohne für den Verbraucher annehmbar — Mean · WW Jubach Trinkw
Sodium 5,4 mg / l 200 mg/l — Mean · WW Jubach Trinkw
Sulphate 9 mg / l 250 mg/l — Mean · WW Jubach Trinkw
Temperature 10,7 °C — — Mean · WW Jubach Trinkw
Total organic carbon (TOC) 0,9 mg / l ohne anormale Veränderung — Mean · WW Jubach Trinkw
Turbidity 0,05 FNU 1 NTU — Mean · WW Jubach Trinkw

Further parameters (6)

Further parameters – WW Jubach Trinkw
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 0,67 mmol / l — — Mean · WW Jubach Trinkw
Base capacity to pH 8.2 n.u. (pH > 8,2) mmol / l
not determined
 — — Mean · WW Jubach Trinkw
Calcium 17,5 mg / l — — Mean · WW Jubach Trinkw
Magnesium 3,0 mg / l — — Mean · WW Jubach Trinkw
Potassium 0,7 mg / l — — Mean · WW Jubach Trinkw
Sum of alkaline earth metals 3,1 °dH — — Mean · WW Jubach Trinkw

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.stadtwerke-halver.de/wasser.html · Jahresmittelwerte 2023 · retrieved on 11/07/2026

Treckinghausen

Stadtwerke Lüdenscheid

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2017. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Key values Treckinghausen
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 4,2 mg / l 50 mg/l — Mean
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean
Sulphate 9 mg / l 250 mg/l — Mean
Sodium 7,1 mg / l 200 mg/l — Mean
Show all recorded parameters (27 — most recent value per parameter)

Microbiology (1)

Microbiology – Treckinghausen
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 / 100 ml 0/100 ml — Maximum · Median 0

Chemical parameters (5)

Chemical parameters – Treckinghausen
Parameter Value Parametric value Share of the parametric value Reference
Fluoride 0,06 mg/l 1.5 mg/l
4 %
Mean
Lead <0,001 mg / l
below limit of quantification
 10 µg/l — Mean
Nitrate 4,2 mg / l 50 mg/l — Mean
Nitrite <0,01 mg / l
below limit of quantification
 0.5 mg/l — Mean
Uranium <0,0001 mg / l
below limit of quantification
 10 µg/l — Mean

Indicator parameters (12)

Indicator parameters – Treckinghausen
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,01 mg / l 0.2 mg/l — Mean
Ammonium <0,04 mg / l
below limit of quantification
 0.5 mg/l — Mean
Chloride 13 mg / l 250 mg/l — Mean
Clostridium perfringens (including spores) 0 / 100 ml 0/100 ml — Maximum · Median 0
Iron <0,01 mg / l
below limit of quantification
 0.2 mg/l — Mean
Manganese <0,005 mg / l
below limit of quantification
 50 µg/l — Mean
Odour geruchlos für den Verbraucher annehmbar — Single value
Sodium 7,1 mg / l 200 mg/l — Mean
Sulphate 9 mg / l 250 mg/l — Mean
Temperature 6,8 °C — — Mean
Total organic carbon (TOC) 0,8 mg/l ohne anormale Veränderung — Mean
Turbidity 0,08 FNU 1 NTU — Mean

Further parameters (9)

Further parameters – Treckinghausen
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 0,5 mmol / l — — Mean
Base capacity to pH 8.2 nicht untersucht, da pH-Wert ≥ 8,2 mmol / l
not determined
 — — Single value
Calcium 12,0 mg / l — — Mean
Dissolved organic carbon (DOC) 0,8 mg/l — — Mean
Magnesium 2,3 mg / l — — Mean
Phosphate <0,01 mg / l
below limit of quantification
 — — Mean
Potassium 0,7 mg / l — — Mean
Silicate / silicic acid 2,5 mg / l — — Mean
Sum of alkaline earth metals 0,4 mmol / l — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.stadtwerke-meinerzhagen.de/de/Produkte/Wasser/Wasseranalyse/Wasseranalyse/Trinkwasseranalyse-Stadtwerke-Luedenscheid.pdf · Jahresmittelwert 2017 · retrieved on 14/07/2026

Wasserwerk Erlenhagen

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.5 °dH
Hardness range soft
Key values Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml — Single value
Show all recorded parameters (49 — most recent value per parameter)

Microbiology (2)

Microbiology – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml — Single value
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Single value

Chemical parameters (12)

Chemical parameters – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00010 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Single value
Benzene <0,00010 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Single value
Benzo(a)pyrene <0,000010 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Single value
Chromium <0,00050 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Single value
Cyanide <0,0050 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Single value
Dibromoacetic acid <0,001 mg/l
below limit of quantification
 — — Single value
Dichloroacetic acid 0,0018 mg/l — — Single value
Monobromoacetic acid <0,001 mg/l
below limit of quantification
 — — Single value
Monochloroacetic acid <0,001 mg/l
below limit of quantification
 — — Single value
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Single value
Trichloroacetic acid <0,001 mg/l
below limit of quantification
 — — Single value
Trihalomethanes — Total 0,0058 mg/l 50 µg/l
12 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (18)

PFAS – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Perfluorobutane sulfonic acid (PFBS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorobutanoic acid (PFBA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorodecanoic acid (PFDA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorododecane sulfonic acid (PFDoDS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorododecanoic acid (PFDoDA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluoroheptane sulfonic acid (PFHpS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluoroheptanoic acid (PFHpA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorohexane sulfonic acid (PFHxS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorohexanoic acid (PFHxA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorononane sulfonic acid (PFNS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorononanoic acid (PFNA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorooctanesulfonic acid (PFOS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorooctanoic acid (PFOA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluoropentanesulfonic acid (PFPeS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluoropentanoic acid (PFPeA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorotridecanesulfonic acid (PFTrDS) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluorotridecanoic acid (PFTrDA) <0,000001 mg/l
below limit of quantification
 — — Single value
Perfluoroundecanoic acid (PFUnDA) <0,000001 mg/l
below limit of quantification
 — — Single value

Indicator parameters (15)

Indicator parameters – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Single value
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Single value
Clostridium perfringens (including spores) 0 KBE/100 ml 0/100 ml — Single value
Coliform bacteria 0 MPN/100 ml 0/100 ml — Single value
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung — Single value
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung — Single value
Iron 0,020 mg/l 0.2 mg/l
10 %
Single value
Manganese <0,0050 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Single value
Odour kein ungewöhnlicher Geruch für den Verbraucher annehmbar — Single value
pH 8,2 6,5–9,5 — Single value
Taste o.B. für den Verbraucher annehmbar — Single value
Temperature 5,5 °C — — Single value
Threshold odour number (TON) <1 TON
below limit of quantification
 — — Single value
Total organic carbon (TOC) 2,5 mg/l ohne anormale Veränderung — Single value
Turbidity 0,05 NTU 1 NTU — Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (2)

Further parameters – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Copper quotient 9,2 — — Single value
Total hardness 4,5 °dH — — Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bergische-energie.de/fileadmin/user_upload/03_Wasser/5_Sonstige/Wipperfuerth_Analyse__April_2026_Wasserwerk_Erlenhagen.pdf · 07.04.2026 · retrieved on 11/07/2026

bergneustadt gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
 50/100 ml
UBA guide value
 — Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
 5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
 2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
 2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
 1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
 — — Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
 — — Mean
Nickel <0,001 mg/l
below limit of quantification
 20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
 0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
 10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
 0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean

Indicator parameters (21)

Indicator parameters – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 — Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml — Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml — Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colour <0,1 m-1
below limit of quantification
 0.5 m⁻¹ — Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm — Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar — Mean
Oxidisability <0,5 mg/l
below limit of quantification
 5 mg/l O2 — Mean
pH 8,2 pH-Einheiten 6,5–9,5 — Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar — Mean
Temperature 13,4 °C — — Maximum
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung — Mean
Turbidity 0,05 NTU 1 NTU — Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
 100 Bq/l — Single value

Further parameters (10)

Further parameters – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l — — Mean
Carbonate hardness 3,5 °dH — — Mean
Copper quotient 10,1 — — Mean
Lithium <0,10 mg/l
below limit of quantification
 — — Mean
Magnesium 2,7 mg/l — — Mean
Phosphate <0,03 mg/l
below limit of quantification
 — — Mean
Potassium <1,0 mg/l
below limit of quantification
 — — Mean
Silicate / silicic acid 3,1 mg/l — — Mean
Total hardness 0,78 mmol/l — — Mean
Zinc <0,005 mg/l
below limit of quantification
 — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.aggerverband.de/trinkwasser/trinkwasseranalyse-qualitaetskontrolle?file=files/assets/trinkwasser/qualitaetskontrolle/JMW_2025.pdf · Jahresmittelwert 2025 · retrieved on 11/07/2026

gummersbach gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values gummersbach gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – gummersbach gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
 50/100 ml
UBA guide value
 — Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – gummersbach gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
 5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
 2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
 2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
 1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
 — — Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
 — — Mean
Nickel <0,001 mg/l
below limit of quantification
 20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
 0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
 10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
 0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – gummersbach gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean

Indicator parameters (21)

Indicator parameters – gummersbach gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 — Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml — Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml — Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colour <0,1 m-1
below limit of quantification
 0.5 m⁻¹ — Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm — Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar — Mean
Oxidisability <0,5 mg/l
below limit of quantification
 5 mg/l O2 — Mean
pH 8,2 pH-Einheiten 6,5–9,5 — Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar — Mean
Temperature 13,4 °C — — Maximum
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung — Mean
Turbidity 0,05 NTU 1 NTU — Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – gummersbach gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
 100 Bq/l — Mean

Further parameters (10)

Further parameters – gummersbach gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l — — Mean
Carbonate hardness 3,5 °dH — — Mean
Copper quotient 10,1 — — Mean
Lithium <0,10 mg/l
below limit of quantification
 — — Mean
Magnesium 2,7 mg/l — — Mean
Phosphate <0,03 mg/l
below limit of quantification
 — — Mean
Potassium <1,0 mg/l
below limit of quantification
 — — Mean
Silicate / silicic acid 3,1 mg/l — — Mean
Total hardness 0,78 mmol/l — — Mean
Zinc <0,005 mg/l
below limit of quantification
 — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.aggerverband.de/trinkwasser/trinkwasseranalyse-qualitaetskontrolle?file=files/assets/trinkwasser/qualitaetskontrolle/JMW_2025.pdf · 2025 · retrieved on 11/07/2026

lindlar gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values lindlar gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – lindlar gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
 50/100 ml
UBA guide value
 — Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – lindlar gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
 5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
 2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
 2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
 1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
 — — Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
 — — Mean
Nickel <0,001 mg/l
below limit of quantification
 20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
 0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
 10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
 0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – lindlar gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean

Indicator parameters (21)

Indicator parameters – lindlar gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 — Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml — Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml — Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colour <0,1 m-1
below limit of quantification
 0.5 m⁻¹ — Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm — Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar — Mean
Oxidisability <0,5 mg/l
below limit of quantification
 5 mg/l O2 — Mean
pH 8,2 pH-Einheiten 6,5–9,5 — Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar — Mean
Temperature 13,4 °C — — Maximum
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung — Mean
Turbidity 0,05 NTU 1 NTU — Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – lindlar gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
 100 Bq/l — Mean

Further parameters (10)

Further parameters – lindlar gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l — — Mean
Carbonate hardness 3,5 °dH — — Mean
Copper quotient 10,1 — — Mean
Lithium <0,10 mg/l
below limit of quantification
 — — Mean
Magnesium 2,7 mg/l — — Mean
Phosphate <0,03 mg/l
below limit of quantification
 — — Mean
Potassium <1,0 mg/l
below limit of quantification
 — — Mean
Silicate / silicic acid 3,1 mg/l — — Mean
Total hardness 0,78 mmol/l — — Mean
Zinc <0,005 mg/l
below limit of quantification
 — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.aggerverband.de/trinkwasser/trinkwasseranalyse-qualitaetskontrolle?file=files/assets/trinkwasser/qualitaetskontrolle/JMW_2025.pdf · Jahresmittelwert 2025 · retrieved on 11/07/2026

nuembrecht gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values nuembrecht gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – nuembrecht gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
 50/100 ml
UBA guide value
 — Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – nuembrecht gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
 5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
 2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
 2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
 1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
 — — Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
 — — Mean
Nickel <0,001 mg/l
below limit of quantification
 20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
 0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
 10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
 0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – nuembrecht gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean

Indicator parameters (21)

Indicator parameters – nuembrecht gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 — Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml — Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml — Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colour <0,1 m-1
below limit of quantification
 0.5 m⁻¹ — Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm — Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar — Mean
Oxidisability <0,5 mg/l
below limit of quantification
 5 mg/l O2 — Mean
pH 8,2 pH-Einheiten 6,5–9,5 — Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar — Mean
Temperature 13,4 °C — — Maximum
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung — Mean
Turbidity 0,05 NTU 1 NTU — Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – nuembrecht gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
 100 Bq/l — Mean

Further parameters (10)

Further parameters – nuembrecht gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l — — Mean
Carbonate hardness 3,5 °dH — — Mean
Copper quotient 10,1 — — Mean
Lithium <0,10 mg/l
below limit of quantification
 — — Mean
Magnesium 2,7 mg/l — — Mean
Phosphate <0,03 mg/l
below limit of quantification
 — — Mean
Potassium <1,0 mg/l
below limit of quantification
 — — Mean
Silicate / silicic acid 3,1 mg/l — — Mean
Total hardness 0,78 mmol/l — — Mean
Zinc <0,005 mg/l
below limit of quantification
 — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.aggerverband.de/files/assets/trinkwasser/qualitaetskontrolle/JMW_2025.pdf · Jahresmittelwert 2025 · retrieved on 11/07/2026

reichshof gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values reichshof gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – reichshof gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
 50/100 ml
UBA guide value
 — Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – reichshof gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
 5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
 2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
 2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
 1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
 — — Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
 — — Mean
Nickel <0,001 mg/l
below limit of quantification
 20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
 0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
 10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
 0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – reichshof gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean

Indicator parameters (21)

Indicator parameters – reichshof gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 — Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml — Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml — Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colour <0,1 m-1
below limit of quantification
 0.5 m⁻¹ — Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm — Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar — Mean
Oxidisability <0,5 mg/l
below limit of quantification
 5 mg/l O2 — Mean
pH 8,2 pH-Einheiten 6,5–9,5 — Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar — Mean
Temperature 13,4 °C — — Maximum
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung — Mean
Turbidity 0,05 NTU 1 NTU — Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – reichshof gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
 100 Bq/l — Mean

Further parameters (10)

Further parameters – reichshof gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l — — Mean
Carbonate hardness 3,5 °dH — — Mean
Copper quotient 10,1 — — Mean
Lithium <0,10 mg/l
below limit of quantification
 — — Mean
Magnesium 2,7 mg/l — — Mean
Phosphate <0,03 mg/l
below limit of quantification
 — — Mean
Potassium <1,0 mg/l
below limit of quantification
 — — Mean
Silicate / silicic acid 3,1 mg/l — — Mean
Total hardness 0,78 mmol/l — — Mean
Zinc <0,005 mg/l
below limit of quantification
 — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.aggerverband.de/trinkwasser/trinkwasseranalyse-qualitaetskontrolle?file=files/assets/trinkwasser/qualitaetskontrolle/JMW_2025.pdf · Jahresmittelwert 2025 · retrieved on 11/07/2026

wiehl gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values wiehl gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – wiehl gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
 50/100 ml
UBA guide value
 — Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – wiehl gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
 5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
 2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
 2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
 1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
 — — Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
 — — Mean
Nickel <0,001 mg/l
below limit of quantification
 20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
 0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
 10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
 0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – wiehl gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean

Indicator parameters (21)

Indicator parameters – wiehl gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 — Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml — Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml — Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colour <0,1 m-1
below limit of quantification
 0.5 m⁻¹ — Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm — Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar — Mean
Oxidisability <0,5 mg/l
below limit of quantification
 5 mg/l O2 — Mean
pH 8,2 pH-Einheiten 6,5–9,5 — Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar — Mean
Temperature 13,4 °C — — Maximum
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung — Mean
Turbidity 0,05 NTU 1 NTU — Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – wiehl gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
 100 Bq/l — Mean

Further parameters (10)

Further parameters – wiehl gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l — — Mean
Carbonate hardness 3,5 °dH — — Mean
Copper quotient 10,1 — — Mean
Lithium <0,10 mg/l
below limit of quantification
 — — Mean
Magnesium 2,7 mg/l — — Mean
Phosphate <0,03 mg/l
below limit of quantification
 — — Mean
Potassium <1,0 mg/l
below limit of quantification
 — — Mean
Silicate / silicic acid 3,1 mg/l — — Mean
Total hardness 0,78 mmol/l — — Mean
Zinc <0,005 mg/l
below limit of quantification
 — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.aggerverband.de/files/assets/trinkwasser/qualitaetskontrolle/JMW_2025.pdf · Jahresmittelwert 2025 · retrieved on 11/07/2026

waldbroel gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values waldbroel gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – waldbroel gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml — Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml — Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
 50/100 ml
UBA guide value
 — Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – waldbroel gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
 5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
 10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
 2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
 3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
 25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
 2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
 1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
 — — Mean
Lead <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
 1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
 — — Mean
Nickel <0,001 mg/l
below limit of quantification
 20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
 0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
 10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
 10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
 0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – waldbroel gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l — — Mean

Indicator parameters (21)

Indicator parameters – waldbroel gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
 0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
 0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 — Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml — Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml — Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
 ohne anormale Veränderung — Mean
Colour <0,1 m-1
below limit of quantification
 0.5 m⁻¹ — Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm — Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
 50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar — Mean
Oxidisability <0,5 mg/l
below limit of quantification
 5 mg/l O2 — Mean
pH 8,2 pH-Einheiten 6,5–9,5 — Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar — Mean
Temperature 4,1 - 13,4 °C — — Mean
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung — Mean
Turbidity 0,05 NTU 1 NTU — Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – waldbroel gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
 100 Bq/l — Mean

Further parameters (10)

Further parameters – waldbroel gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l — — Mean
Carbonate hardness 3,5 °dH — — Mean
Copper quotient 10,1 — — Mean
Lithium <0,10 mg/l
below limit of quantification
 — — Mean
Magnesium 2,7 mg/l — — Mean
Phosphate <0,03 mg/l
below limit of quantification
 — — Mean
Potassium <1,0 mg/l
below limit of quantification
 — — Mean
Silicate / silicic acid 3,1 mg/l — — Mean
Total hardness 0,78 mmol/l — — Mean
Zinc <0,005 mg/l
below limit of quantification
 — — Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.aggerverband.de/trinkwasser/trinkwasseranalyse-qualitaetskontrolle?file=files/assets/trinkwasser/qualitaetskontrolle/JMW_2025.pdf · Jahresmittelwert 2025 · retrieved on 11/07/2026

Frequent questions about postcode 58553

Who supplies the drinking water in Postcode 58553?
Stadtwerke Halver GmbH. The values shown here come from the supply zone Brunnen Büchermühle TW and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.