Skip to content
maunawai.info

Drinking water in 56346

For this postcode the responsible water supplier publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 2 underneath.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
8.1 °dH
Hardness range soft
Key values Bornich
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Bornich
Nitrate 38.8 mg/L 50 mg/l
78 %
Mean · Bornich
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Bornich
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Bornich
Sulphate 27.4 mg/L 250 mg/l
11 %
Mean · Bornich
Sodium 13.8 mg/L 200 mg/l
7 %
Mean · Bornich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Bornich
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Bornich

Chemical parameters (14)

Chemical parameters – Bornich
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 0.5 µg/L
below limit of quantification
5 µg/l
< 10 % *
Mean · Bornich
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Bornich
Boron < 0.02 mg/L
below limit of quantification
1 mg/l
< 2 % *
Mean · Bornich
Cadmium < 0.3 µg/L
below limit of quantification
3 µg/l
< 10 % *
Mean · Bornich
Copper < 0.005 mg/L
below limit of quantification
2 mg/l
< 0.3 % *
Mean · Bornich
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Bornich
Fluoride 0.13 mg/L 1.5 mg/l
9 %
Mean · Bornich
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Bornich
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Bornich
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Bornich
Nitrate 38.8 mg/L 50 mg/l
78 %
Mean · Bornich
Nitrite < 0.01 mg/L
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Bornich
Selenium < 0.5 µg/L
below limit of quantification
10 µg/l
< 5 % *
Mean · Bornich
Uranium 0.11 µg/L 10 µg/l
1 %
Mean · Bornich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Bornich
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Bornich

Indicator parameters (10)

Indicator parameters – Bornich
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Bornich
Ammonium < 0.01 mg/L
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Bornich
Chloride 22.1 mg/L 250 mg/l
9 %
Mean · Bornich
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Bornich
Iron 0.055 mg/L 0.2 mg/l
28 %
Mean · Bornich
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Bornich
pH 8.23 - 6,5–9,5 Mean · Bornich
Sodium 13.8 mg/L 200 mg/l
7 %
Mean · Bornich
Sulphate 27.4 mg/L 250 mg/l
11 %
Mean · Bornich
Temperature 16 °C Mean · Bornich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Bornich
Parameter Value Parametric value Share of the parametric value Reference
Calcium 32.2 mg/L Mean · Bornich
Magnesium 8.8 mg/L Mean · Bornich
Potassium 2 mg/L Mean · Bornich
Total hardness 1.44 mmol/l Mean · Bornich

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2573695125/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026
Show 2 more supply zones in this postcode

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
12.2 °dH
Hardness range medium
Key values Lykershausen-Prath
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Lykershausen-Prath
Nitrate 30.8 mg/L 50 mg/l
62 %
Mean · Lykershausen-Prath
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Lykershausen-Prath
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Lykershausen-Prath
Sulphate 37 mg/L 250 mg/l
15 %
Mean · Lykershausen-Prath
Sodium 10.3 mg/L 200 mg/l
5 %
Mean · Lykershausen-Prath

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Lykershausen-Prath
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Lykershausen-Prath

Chemical parameters (14)

Chemical parameters – Lykershausen-Prath
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · Lykershausen-Prath
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Lykershausen-Prath
Boron < 0.05 mg/L
below limit of quantification
1 mg/l
< 5 % *
Mean · Lykershausen-Prath
Cadmium < 0.5 µg/L
below limit of quantification
3 µg/l
< 17 % *
Mean · Lykershausen-Prath
Copper 0.011 mg/L 2 mg/l
0.5 %
Mean · Lykershausen-Prath
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Lykershausen-Prath
Fluoride 0.2 mg/L 1.5 mg/l
13 %
Mean · Lykershausen-Prath
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Lykershausen-Prath
Mercury < 0.05 µg/L
below limit of quantification
1 µg/l
< 5 % *
Mean · Lykershausen-Prath
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Lykershausen-Prath
Nitrate 30.8 mg/L 50 mg/l
62 %
Mean · Lykershausen-Prath
Nitrite < 0.02 mg/L
below limit of quantification
0.5 mg/l
< 4 % *
Mean · Lykershausen-Prath
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Lykershausen-Prath
Uranium 0.5 µg/L 10 µg/l
5 %
Mean · Lykershausen-Prath

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Lykershausen-Prath
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Lykershausen-Prath

Indicator parameters (10)

Indicator parameters – Lykershausen-Prath
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Lykershausen-Prath
Ammonium < 0.04 mg/L
below limit of quantification
0.5 mg/l
< 8 % *
Mean · Lykershausen-Prath
Chloride 24.5 mg/L 250 mg/l
10 %
Mean · Lykershausen-Prath
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Lykershausen-Prath
Iron < 0.01 mg/L
below limit of quantification
0.2 mg/l
< 5 % *
Mean · Lykershausen-Prath
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Lykershausen-Prath
pH 7.8 - 6,5–9,5 Mean · Lykershausen-Prath
Sodium 10.3 mg/L 200 mg/l
5 %
Mean · Lykershausen-Prath
Sulphate 37 mg/L 250 mg/l
15 %
Mean · Lykershausen-Prath
Temperature 7 °C Mean · Lykershausen-Prath

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Lykershausen-Prath
Parameter Value Parametric value Share of the parametric value Reference
Calcium 66.9 mg/L Mean · Lykershausen-Prath
Magnesium 12.3 mg/L Mean · Lykershausen-Prath
Potassium 1 mg/L Mean · Lykershausen-Prath
Total hardness 2.18 mmol/l Mean · Lykershausen-Prath

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2577695529/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

RHW Übergabe an St. Goarshausen (WW), TW

TWIST RLP - RHW Übergabe an St. Goarshausen (WW), TW

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
17.9 °dH
Hardness range hard
Key values RHW Übergabe an St. Goarshausen (WW), TW
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.025 µg/L 0.1 µg/l
25 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Nitrate 14.1 mg/L 50 mg/l
28 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · RHW Übergabe an St. Goarshausen (WW), TW
Sulphate 67 mg/L 250 mg/l
27 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Sodium 64.2 mg/L 200 mg/l
32 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – RHW Übergabe an St. Goarshausen (WW), TW
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · RHW Übergabe an St. Goarshausen (WW), TW

Chemical parameters (14)

Chemical parameters – RHW Übergabe an St. Goarshausen (WW), TW
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Boron 0.08 mg/L 1 mg/l
8 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Cadmium < 0.5 µg/L
below limit of quantification
3 µg/l
< 17 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Copper < 0.005 mg/L
below limit of quantification
2 mg/l
< 0.3 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Fluoride < 0.2 mg/L
below limit of quantification
1.5 mg/l
< 13 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Mercury < 0.05 µg/L
below limit of quantification
1 µg/l
< 5 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Nitrate 14.1 mg/L 50 mg/l
28 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Nitrite < 0.02 mg/L
below limit of quantification
0.5 mg/l
< 4 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Uranium 1.3 µg/L 10 µg/l
13 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – RHW Übergabe an St. Goarshausen (WW), TW
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.025 µg/L 0.1 µg/l
25 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW

Indicator parameters (10)

Indicator parameters – RHW Übergabe an St. Goarshausen (WW), TW
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Ammonium < 0.04 mg/L
below limit of quantification
0.5 mg/l
< 8 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Chloride 109 mg/L 250 mg/l
44 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · RHW Übergabe an St. Goarshausen (WW), TW
Iron < 0.01 mg/L
below limit of quantification
0.2 mg/l
< 5 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · RHW Übergabe an St. Goarshausen (WW), TW
pH 8.02 - 6,5–9,5 Mean · RHW Übergabe an St. Goarshausen (WW), TW
Sodium 64.2 mg/L 200 mg/l
32 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Sulphate 67 mg/L 250 mg/l
27 %
Mean · RHW Übergabe an St. Goarshausen (WW), TW
Temperature 6 °C Mean · RHW Übergabe an St. Goarshausen (WW), TW

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – RHW Übergabe an St. Goarshausen (WW), TW
Parameter Value Parametric value Share of the parametric value Reference
Calcium 97.3 mg/L Mean · RHW Übergabe an St. Goarshausen (WW), TW
Magnesium 18.1 mg/L Mean · RHW Übergabe an St. Goarshausen (WW), TW
Potassium 7.8 mg/L Mean · RHW Übergabe an St. Goarshausen (WW), TW
Total hardness 3.2 mmol/l Mean · RHW Übergabe an St. Goarshausen (WW), TW

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2573695238/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Frequent questions about postcode 56346

How hard is the water in Postcode 56346?
TWIST RLP - Bornich publishes a total hardness of 1.44 mmol/l for the supply zone Bornich — that corresponds to 8.1 °dH. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 13/07/2026.
How much nitrate is in the drinking water in Postcode 56346?
TWIST RLP - Bornich publishes a nitrate value of 38.8 mg/L for the supply zone Bornich. The statutory parametric value is 50 mg/l; the measured value represents 78 % of the parametric value. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Are PFAS detectable in the drinking water in Postcode 56346?
TWIST RLP - Bornich publishes for the supply zone Bornich a sum value PFAS-20 of 0 µg/L. The statutory parametric value is 0.1 µg/l; the measured value represents 0 % of the parametric value. For the sum of the 20 individual substances, this parametric value has applied since 12/01/2026. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Who supplies the drinking water in Postcode 56346?
TWIST RLP - Bornich. The values shown here come from the supply zone Bornich and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.