Skip to content
maunawai.info

Drinking water in 56338

For this postcode the responsible water supplier publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 2 underneath.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
15.5 °dH
Hardness range hard
Key values Braubach
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.025 µg/L 0.1 µg/l
25 %
Mean · Braubach
Nitrate 19.1 mg/L 50 mg/l
38 %
Mean · Braubach
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Braubach
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Braubach
Sulphate 62.3 mg/L 250 mg/l
25 %
Mean · Braubach
Sodium 43.4 mg/L 200 mg/l
22 %
Mean · Braubach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Braubach
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Braubach

Chemical parameters (14)

Chemical parameters – Braubach
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 0.5 µg/L
below limit of quantification
5 µg/l
< 10 % *
Mean · Braubach
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Braubach
Boron 0.07 mg/L 1 mg/l
7 %
Mean · Braubach
Cadmium < 0.3 µg/L
below limit of quantification
3 µg/l
< 10 % *
Mean · Braubach
Copper 0.008 mg/L 2 mg/l
0.4 %
Mean · Braubach
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Braubach
Fluoride 0.26 mg/L 1.5 mg/l
17 %
Mean · Braubach
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Braubach
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Braubach
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Braubach
Nitrate 19.1 mg/L 50 mg/l
38 %
Mean · Braubach
Nitrite < 0.01 mg/L
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Braubach
Selenium 1.1 µg/L 10 µg/l
11 %
Mean · Braubach
Uranium 2 µg/L 10 µg/l
20 %
Mean · Braubach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Braubach
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.025 µg/L 0.1 µg/l
25 %
Mean · Braubach

Indicator parameters (10)

Indicator parameters – Braubach
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Braubach
Ammonium < 0.01 mg/L
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Braubach
Chloride 49.5 mg/L 250 mg/l
20 %
Mean · Braubach
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Braubach
Iron < 0.005 mg/L
below limit of quantification
0.2 mg/l
< 3 % *
Mean · Braubach
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Braubach
pH 7.17 - 6,5–9,5 Mean · Braubach
Sodium 43.4 mg/L 200 mg/l
22 %
Mean · Braubach
Sulphate 62.3 mg/L 250 mg/l
25 %
Mean · Braubach
Temperature 11.8 °C Mean · Braubach

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Braubach
Parameter Value Parametric value Share of the parametric value Reference
Calcium 96.3 mg/L Mean · Braubach
Magnesium 17 mg/L Mean · Braubach
Potassium 3.1 mg/L Mean · Braubach
Total hardness 2.76 mmol/l Mean · Braubach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2579695305/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026
Show 2 more supply zones in this postcode

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
13.7 °dH
Hardness range medium
Key values Becheln-Frücht
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Becheln-Frücht
Nitrate 41.3 mg/L 50 mg/l
83 %
Mean · Becheln-Frücht
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Becheln-Frücht
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Becheln-Frücht
Sulphate 25.4 mg/L 250 mg/l
10 %
Mean · Becheln-Frücht
Sodium 21.8 mg/L 200 mg/l
11 %
Mean · Becheln-Frücht

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Becheln-Frücht
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Becheln-Frücht

Chemical parameters (14)

Chemical parameters – Becheln-Frücht
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 0.5 µg/L
below limit of quantification
5 µg/l
< 10 % *
Mean · Becheln-Frücht
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Becheln-Frücht
Boron < 0.02 mg/L
below limit of quantification
1 mg/l
< 2 % *
Mean · Becheln-Frücht
Cadmium < 0.3 µg/L
below limit of quantification
3 µg/l
< 10 % *
Mean · Becheln-Frücht
Copper 0.015 mg/L 2 mg/l
0.8 %
Mean · Becheln-Frücht
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Becheln-Frücht
Fluoride 0.1 mg/L 1.5 mg/l
7 %
Mean · Becheln-Frücht
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Becheln-Frücht
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Becheln-Frücht
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Becheln-Frücht
Nitrate 41.3 mg/L 50 mg/l
83 %
Mean · Becheln-Frücht
Nitrite < 0.01 mg/L
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Becheln-Frücht
Selenium < 0.5 µg/L
below limit of quantification
10 µg/l
< 5 % *
Mean · Becheln-Frücht
Uranium 0.2 µg/L 10 µg/l
2 %
Mean · Becheln-Frücht

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Becheln-Frücht
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Becheln-Frücht

Indicator parameters (10)

Indicator parameters – Becheln-Frücht
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Becheln-Frücht
Ammonium < 0.01 mg/L
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Becheln-Frücht
Chloride 45 mg/L 250 mg/l
18 %
Mean · Becheln-Frücht
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Becheln-Frücht
Iron 0.024 mg/L 0.2 mg/l
12 %
Mean · Becheln-Frücht
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Becheln-Frücht
pH 7.97 - 6,5–9,5 Mean · Becheln-Frücht
Sodium 21.8 mg/L 200 mg/l
11 %
Mean · Becheln-Frücht
Sulphate 25.4 mg/L 250 mg/l
10 %
Mean · Becheln-Frücht
Temperature 10 °C Mean · Becheln-Frücht

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Becheln-Frücht
Parameter Value Parametric value Share of the parametric value Reference
Calcium 43.9 mg/L Mean · Becheln-Frücht
Magnesium 11.2 mg/L Mean · Becheln-Frücht
Potassium 2.5 mg/L Mean · Becheln-Frücht
Total hardness 2.45 mmol/l Mean · Becheln-Frücht

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2589698050/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5.1 °dH
Hardness range soft
Key values Dachsenhausen-Hinterwald
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Dachsenhausen-Hinterwald
Nitrate 6.8 mg/L 50 mg/l
14 %
Mean · Dachsenhausen-Hinterwald
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Dachsenhausen-Hinterwald
Sulphate 14 mg/L 250 mg/l
6 %
Mean · Dachsenhausen-Hinterwald
Sodium 11.7 mg/L 200 mg/l
6 %
Mean · Dachsenhausen-Hinterwald

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Dachsenhausen-Hinterwald
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Dachsenhausen-Hinterwald

Chemical parameters (14)

Chemical parameters – Dachsenhausen-Hinterwald
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · Dachsenhausen-Hinterwald
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
Boron < 0.05 mg/L
below limit of quantification
1 mg/l
< 5 % *
Mean · Dachsenhausen-Hinterwald
Cadmium < 0.5 µg/L
below limit of quantification
3 µg/l
< 17 % *
Mean · Dachsenhausen-Hinterwald
Copper < 0.005 mg/L
below limit of quantification
2 mg/l
< 0.3 % *
Mean · Dachsenhausen-Hinterwald
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
Fluoride < 0.2 mg/L
below limit of quantification
1.5 mg/l
< 13 % *
Mean · Dachsenhausen-Hinterwald
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
Mercury < 0.05 µg/L
below limit of quantification
1 µg/l
< 5 % *
Mean · Dachsenhausen-Hinterwald
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
Nitrate 6.8 mg/L 50 mg/l
14 %
Mean · Dachsenhausen-Hinterwald
Nitrite < 0.02 mg/L
below limit of quantification
0.5 mg/l
< 4 % *
Mean · Dachsenhausen-Hinterwald
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
Uranium < 0.5 µg/L
below limit of quantification
10 µg/l
< 5 % *
Mean · Dachsenhausen-Hinterwald

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Dachsenhausen-Hinterwald
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Dachsenhausen-Hinterwald

Indicator parameters (10)

Indicator parameters – Dachsenhausen-Hinterwald
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
Ammonium < 0.04 mg/L
below limit of quantification
0.5 mg/l
< 8 % *
Mean · Dachsenhausen-Hinterwald
Chloride 14.8 mg/L 250 mg/l
6 %
Mean · Dachsenhausen-Hinterwald
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Dachsenhausen-Hinterwald
Iron 0.04 mg/L 0.2 mg/l
20 %
Mean · Dachsenhausen-Hinterwald
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Dachsenhausen-Hinterwald
pH 7.79 - 6,5–9,5 Mean · Dachsenhausen-Hinterwald
Sodium 11.7 mg/L 200 mg/l
6 %
Mean · Dachsenhausen-Hinterwald
Sulphate 14 mg/L 250 mg/l
6 %
Mean · Dachsenhausen-Hinterwald
Temperature 10 °C Mean · Dachsenhausen-Hinterwald

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Dachsenhausen-Hinterwald
Parameter Value Parametric value Share of the parametric value Reference
Calcium 22.1 mg/L Mean · Dachsenhausen-Hinterwald
Magnesium 8.77 mg/L Mean · Dachsenhausen-Hinterwald
Potassium 1.5 mg/L Mean · Dachsenhausen-Hinterwald
Total hardness 0.91 mmol/l Mean · Dachsenhausen-Hinterwald

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2578695002/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Frequent questions about postcode 56338

How hard is the water in Postcode 56338?
TWIST RLP - Braubach publishes a total hardness of 2.76 mmol/l for the supply zone Braubach — that corresponds to 15.5 °dH. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 13/07/2026.
How much nitrate is in the drinking water in Postcode 56338?
TWIST RLP - Braubach publishes a nitrate value of 19.1 mg/L for the supply zone Braubach. The statutory parametric value is 50 mg/l; the measured value represents 38 % of the parametric value. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Are PFAS detectable in the drinking water in Postcode 56338?
TWIST RLP - Braubach publishes for the supply zone Braubach a sum value PFAS-20 of 0.025 µg/L. The statutory parametric value is 0.1 µg/l; the measured value represents 25 % of the parametric value. For the sum of the 20 individual substances, this parametric value has applied since 12/01/2026. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Who supplies the drinking water in Postcode 56338?
TWIST RLP - Braubach. The values shown here come from the supply zone Braubach and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.