Skip to content
maunawai.info

Drinking water in 55758

For this postcode the responsible water supplier publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 11 underneath. The water supplier publishes 4 further local networks that cannot be clearly assigned to this postcode — they are listed on the water supplier page.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
4.5 °dH
Hardness range soft
Key values Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Steinbachtalsperre
Nitrate 1.6 mg/L 50 mg/l
3 %
Mean · Steinbachtalsperre
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Steinbachtalsperre
Sulphate 18 mg/L 250 mg/l
7 %
Mean · Steinbachtalsperre
Sodium 7.6 mg/L 200 mg/l
4 %
Mean · Steinbachtalsperre

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (31 — most recent value per parameter)

Microbiology (1)

Microbiology – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Steinbachtalsperre

Chemical parameters (14)

Chemical parameters – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Antimony 3 µg/L 5 µg/l
60 %
Mean · Steinbachtalsperre
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · Steinbachtalsperre
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · Steinbachtalsperre
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · Steinbachtalsperre
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Steinbachtalsperre
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · Steinbachtalsperre
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Steinbachtalsperre
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Steinbachtalsperre
Nitrate 1.6 mg/L 50 mg/l
3 %
Mean · Steinbachtalsperre
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · Steinbachtalsperre
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Steinbachtalsperre
Uranium < 0.2 µg/L
below limit of quantification
10 µg/l
< 2 % *
Mean · Steinbachtalsperre

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Steinbachtalsperre

Indicator parameters (10)

Indicator parameters – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Steinbachtalsperre
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · Steinbachtalsperre
Chloride 12 mg/L 250 mg/l
5 %
Mean · Steinbachtalsperre
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Steinbachtalsperre
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · Steinbachtalsperre
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Steinbachtalsperre
pH 8 - 6,5–9,5 Mean · Steinbachtalsperre
Sodium 7.6 mg/L 200 mg/l
4 %
Mean · Steinbachtalsperre
Sulphate 18 mg/L 250 mg/l
7 %
Mean · Steinbachtalsperre
Temperature 13.8 °C Mean · Steinbachtalsperre

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (5)

Further parameters – Steinbachtalsperre
Parameter Value Parametric value Share of the parametric value Reference
Calcium 36 mg/L Mean · Steinbachtalsperre
Magnesium 2.6 mg/L Mean · Steinbachtalsperre
Potassium < 0.3 mg/L
below limit of quantification
Mean · Steinbachtalsperre
Total hardness 0.8 mmol/l Mean · Steinbachtalsperre
Zinc 0.006 mg/L Mean · Steinbachtalsperre

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541695100/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026
Show 11 more supply zones in this postcode

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5.6 °dH
Hardness range soft
Key values HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS < 0.02 µg/L
below limit of quantification
0.1 µg/l
< 20 % *
Mean · HB Silberich
Nitrate 3.4 mg/L 50 mg/l
7 %
Mean · HB Silberich
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · HB Silberich
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · HB Silberich
Sulphate 16 mg/L 250 mg/l
6 %
Mean · HB Silberich
Sodium 7.3 mg/L 200 mg/l
4 %
Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · HB Silberich

Chemical parameters (14)

Chemical parameters – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · HB Silberich
Arsenic < 2 µg/L
below limit of quantification
10 µg/l
< 20 % *
Mean · HB Silberich
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · HB Silberich
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · HB Silberich
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · HB Silberich
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · HB Silberich
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · HB Silberich
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · HB Silberich
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · HB Silberich
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · HB Silberich
Nitrate 3.4 mg/L 50 mg/l
7 %
Mean · HB Silberich
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · HB Silberich
Selenium 4 µg/L 10 µg/l
40 %
Mean · HB Silberich
Uranium < 0.5 µg/L
below limit of quantification
10 µg/l
< 5 % *
Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS < 0.02 µg/L
below limit of quantification
0.1 µg/l
< 20 % *
Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (10)

Indicator parameters – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · HB Silberich
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · HB Silberich
Chloride 11 mg/L 250 mg/l
4 %
Mean · HB Silberich
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · HB Silberich
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · HB Silberich
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · HB Silberich
pH 8.1 - 6,5–9,5 Mean · HB Silberich
Sodium 7.3 mg/L 200 mg/l
4 %
Mean · HB Silberich
Sulphate 16 mg/L 250 mg/l
6 %
Mean · HB Silberich
Temperature 13.9 °C Mean · HB Silberich

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – HB Silberich
Parameter Value Parametric value Share of the parametric value Reference
Calcium 35 mg/L Mean · HB Silberich
Magnesium 2.5 mg/L Mean · HB Silberich
Potassium < 0.3 mg/L
below limit of quantification
Mean · HB Silberich
Total hardness 0.99 mmol/l Mean · HB Silberich

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541695087/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
16.4 °dH
Hardness range hard
Key values Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.01 µg/L 0.1 µg/l
10 %
Mean · Limbach-Großbachtal
Nitrate 34 mg/L 50 mg/l
68 %
Mean · Limbach-Großbachtal
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Limbach-Großbachtal
Sulphate 29 mg/L 250 mg/l
12 %
Mean · Limbach-Großbachtal
Sodium 14.1 mg/L 200 mg/l
7 %
Mean · Limbach-Großbachtal

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Limbach-Großbachtal

Chemical parameters (14)

Chemical parameters – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · Limbach-Großbachtal
Arsenic 4 µg/L 10 µg/l
40 %
Mean · Limbach-Großbachtal
Boron 0.03 mg/L 1 mg/l
3 %
Mean · Limbach-Großbachtal
Cadmium < 0.2 µg/L
below limit of quantification
3 µg/l
< 7 % *
Mean · Limbach-Großbachtal
Copper < 0.005 mg/L
below limit of quantification
2 mg/l
< 0.3 % *
Mean · Limbach-Großbachtal
Cyanide < 0.003 mg/L
below limit of quantification
50 µg/l
< 6 % *
Mean · Limbach-Großbachtal
Fluoride 0.14 mg/L 1.5 mg/l
9 %
Mean · Limbach-Großbachtal
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Nickel < 5 µg/L
below limit of quantification
20 µg/l
< 25 % *
Mean · Limbach-Großbachtal
Nitrate 34 mg/L 50 mg/l
68 %
Mean · Limbach-Großbachtal
Nitrite 0.008 mg/L 0.5 mg/l
2 %
Mean · Limbach-Großbachtal
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Limbach-Großbachtal
Uranium 4 µg/L 10 µg/l
40 %
Mean · Limbach-Großbachtal

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0.01 µg/L 0.1 µg/l
10 %
Mean · Limbach-Großbachtal

Indicator parameters (10)

Indicator parameters – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.005 mg/L
below limit of quantification
0.2 mg/l
< 3 % *
Mean · Limbach-Großbachtal
Ammonium 0.04 mg/L 0.5 mg/l
8 %
Mean · Limbach-Großbachtal
Chloride 27 mg/L 250 mg/l
11 %
Mean · Limbach-Großbachtal
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Limbach-Großbachtal
Iron < 0.05 mg/L
below limit of quantification
0.2 mg/l
< 25 % *
Mean · Limbach-Großbachtal
Manganese < 0.01 mg/L
below limit of quantification
50 µg/l
< 20 % *
Mean · Limbach-Großbachtal
pH 7.68 - 6,5–9,5 Mean · Limbach-Großbachtal
Sodium 14.1 mg/L 200 mg/l
7 %
Mean · Limbach-Großbachtal
Sulphate 29 mg/L 250 mg/l
12 %
Mean · Limbach-Großbachtal
Temperature 9.5 °C Mean · Limbach-Großbachtal

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Limbach-Großbachtal
Parameter Value Parametric value Share of the parametric value Reference
Calcium 82 mg/L Mean · Limbach-Großbachtal
Magnesium 20.4 mg/L Mean · Limbach-Großbachtal
Potassium 2.8 mg/L Mean · Limbach-Großbachtal
Total hardness 2.93 mmol/l Mean · Limbach-Großbachtal

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541699500/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.3 °dH
Hardness range soft
Key values Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Stipshausen
Nitrate 7.3 mg/L 50 mg/l
15 %
Mean · Stipshausen
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Stipshausen
Sulphate 5.1 mg/L 250 mg/l
2 %
Mean · Stipshausen
Sodium 4.8 mg/L 200 mg/l
2 %
Mean · Stipshausen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Stipshausen

Chemical parameters (14)

Chemical parameters – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Antimony 1 µg/L 5 µg/l
20 %
Mean · Stipshausen
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · Stipshausen
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · Stipshausen
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · Stipshausen
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Stipshausen
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · Stipshausen
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Stipshausen
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Stipshausen
Nitrate 7.3 mg/L 50 mg/l
15 %
Mean · Stipshausen
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · Stipshausen
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Stipshausen
Uranium < 0.2 µg/L
below limit of quantification
10 µg/l
< 2 % *
Mean · Stipshausen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Stipshausen

Indicator parameters (10)

Indicator parameters – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0.024 mg/L 0.2 mg/l
12 %
Mean · Stipshausen
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · Stipshausen
Chloride 9.3 mg/L 250 mg/l
4 %
Mean · Stipshausen
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Stipshausen
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · Stipshausen
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Stipshausen
pH 8.2 - 6,5–9,5 Mean · Stipshausen
Sodium 4.8 mg/L 200 mg/l
2 %
Mean · Stipshausen
Sulphate 5.1 mg/L 250 mg/l
2 %
Mean · Stipshausen
Temperature 10 °C Mean · Stipshausen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Stipshausen
Parameter Value Parametric value Share of the parametric value Reference
Calcium 21 mg/L Mean · Stipshausen
Magnesium 1.4 mg/L Mean · Stipshausen
Potassium < 0.3 mg/L
below limit of quantification
Mean · Stipshausen
Total hardness 0.58 mmol/l Mean · Stipshausen

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2542695029/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.9 °dH
Hardness range soft
Key values WiLa
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · WiLa
Nitrate 6.7 mg/L 50 mg/l
13 %
Mean · WiLa
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · WiLa
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · WiLa
Sulphate 6.7 mg/L 250 mg/l
3 %
Mean · WiLa
Sodium 3.7 mg/L 200 mg/l
2 %
Mean · WiLa

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (30 — most recent value per parameter)

Microbiology (1)

Microbiology – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · WiLa

Chemical parameters (14)

Chemical parameters – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Antimony 1 µg/L 5 µg/l
20 %
Mean · WiLa
Arsenic 4 µg/L 10 µg/l
40 %
Mean · WiLa
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · WiLa
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · WiLa
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · WiLa
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · WiLa
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · WiLa
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · WiLa
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · WiLa
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · WiLa
Nitrate 6.7 mg/L 50 mg/l
13 %
Mean · WiLa
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · WiLa
Selenium < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · WiLa
Uranium < 0.2 µg/L
below limit of quantification
10 µg/l
< 2 % *
Mean · WiLa

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · WiLa

Indicator parameters (10)

Indicator parameters – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · WiLa
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · WiLa
Chloride 7.2 mg/L 250 mg/l
3 %
Mean · WiLa
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · WiLa
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · WiLa
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · WiLa
pH 8.3 - 6,5–9,5 Mean · WiLa
Sodium 3.7 mg/L 200 mg/l
2 %
Mean · WiLa
Sulphate 6.7 mg/L 250 mg/l
3 %
Mean · WiLa
Temperature 11.8 °C Mean · WiLa

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – WiLa
Parameter Value Parametric value Share of the parametric value Reference
Calcium 23 mg/L Mean · WiLa
Magnesium 1.4 mg/L Mean · WiLa
Potassium < 0.3 mg/L
below limit of quantification
Mean · WiLa
Total hardness 0.7 mmol/l Mean · WiLa

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541695302/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Key values Thranenweier
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Thranenweier
Nitrate 6.6 mg/L 50 mg/l
13 %
Mean · Thranenweier
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Thranenweier
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Thranenweier
Sulphate 3.4 mg/L 250 mg/l
1 %
Mean · Thranenweier
Sodium 1.6 mg/L 200 mg/l
0.8 %
Mean · Thranenweier

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (26 — most recent value per parameter)

Microbiology (1)

Microbiology – Thranenweier
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Mean · Thranenweier

Chemical parameters (14)

Chemical parameters – Thranenweier
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 1 µg/L
below limit of quantification
5 µg/l
< 20 % *
Mean · Thranenweier
Arsenic < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Thranenweier
Boron < 0.1 mg/L
below limit of quantification
1 mg/l
< 10 % *
Mean · Thranenweier
Cadmium < 1 µg/L
below limit of quantification
3 µg/l
< 33 % *
Mean · Thranenweier
Copper < 0.002 mg/L
below limit of quantification
2 mg/l
< 0.1 % *
Mean · Thranenweier
Cyanide < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Thranenweier
Fluoride < 0.1 mg/L
below limit of quantification
1.5 mg/l
< 7 % *
Mean · Thranenweier
Lead < 1 µg/L
below limit of quantification
10 µg/l
< 10 % *
Mean · Thranenweier
Mercury < 0.1 µg/L
below limit of quantification
1 µg/l
< 10 % *
Mean · Thranenweier
Nickel < 2 µg/L
below limit of quantification
20 µg/l
< 10 % *
Mean · Thranenweier
Nitrate 6.6 mg/L 50 mg/l
13 %
Mean · Thranenweier
Nitrite < 0.03 mg/L
below limit of quantification
0.5 mg/l
< 6 % *
Mean · Thranenweier
Selenium 8 µg/L 10 µg/l
80 %
Mean · Thranenweier
Uranium < 0.2 µg/L
below limit of quantification
10 µg/l
< 2 % *
Mean · Thranenweier

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – Thranenweier
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 µg/L 0.1 µg/l
0 %
Mean · Thranenweier

Indicator parameters (10)

Indicator parameters – Thranenweier
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0.02 mg/L
below limit of quantification
0.2 mg/l
< 10 % *
Mean · Thranenweier
Ammonium < 0.05 mg/L
below limit of quantification
0.5 mg/l
< 10 % *
Mean · Thranenweier
Chloride 4.3 mg/L 250 mg/l
2 %
Mean · Thranenweier
Coliform bacteria 0 Anzahl/100ml 0/100 ml Mean · Thranenweier
Iron < 0.001 mg/L
below limit of quantification
0.2 mg/l
< 0.5 % *
Mean · Thranenweier
Manganese < 0.005 mg/L
below limit of quantification
50 µg/l
< 10 % *
Mean · Thranenweier
pH 8.2 - 6,5–9,5 Mean · Thranenweier
Sodium 1.6 mg/L 200 mg/l
0.8 %
Mean · Thranenweier
Sulphate 3.4 mg/L 250 mg/l
1 %
Mean · Thranenweier
Temperature 13.6 °C Mean · Thranenweier

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://geodaten-wasser.rlp-umwelt.de/twist/2541696000/trinkwasserqualitaet · Mittelwerte · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
3.5 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Further parameters (3)

Further parameters – Allenbach
Parameter Value Parametric value Share of the parametric value Reference
Carbonate hardness 0,50 mmol/l Single value · Allenbach
Hardness range (WRMG) weich Single value · Allenbach
Total hardness 3,5 ° dH Single value · Allenbach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Asbach, Bruchweiler, Hammerbirkenfeld, Hellertshausen, Kempfeld, Langweiler, Schauren, Sensweiler, Wirschweiler

Verbandsgemeindewerke Herrstein-Rhaunen

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.1 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Further parameters (3)

Further parameters – Asbach, Bruchweiler, Hammerbirkenfeld, Hellertshausen, Kempfeld, Langweiler, Schauren, Sensweiler, Wirschweiler
Parameter Value Parametric value Share of the parametric value Reference
Carbonate hardness 0,55 mmol/l Single value · Asbach, Bruchweiler, Hammerbirkenfeld, Hellertshausen, Kempfeld, Langweiler, Schauren, Sensweiler, Wirschweiler
Hardness range (WRMG) weich Single value · Asbach, Bruchweiler, Hammerbirkenfeld, Hellertshausen, Kempfeld, Langweiler, Schauren, Sensweiler, Wirschweiler
Total hardness 4,1 ° dH Single value · Asbach, Bruchweiler, Hammerbirkenfeld, Hellertshausen, Kempfeld, Langweiler, Schauren, Sensweiler, Wirschweiler

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Asbacher Hütte (Harfenmühle), Breitenthal, Herborn, Herrstein, Mörschied, Niederhosenbach, Niederwörresbach, Oberhosenbach, Oberwörresbach, Veitsrodt, Vollmersbach, Weiden

Verbandsgemeindewerke Herrstein-Rhaunen

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
5.5 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Further parameters (3)

Further parameters – Asbacher Hütte (Harfenmühle), Breitenthal, Herborn, Herrstein, Mörschied, Niederhosenbach, Niederwörresbach, Oberhosenbach, Oberwörresbach, Veitsrodt, Vollmersbach, Weiden
Parameter Value Parametric value Share of the parametric value Reference
Carbonate hardness 0,71 mmol/l Single value · Asbacher Hütte (Harfenmühle), Breitenthal, Herborn, Herrstein, Mörschied, Niederhosenbach, Niederwörresbach, Oberhosenbach, Oberwörresbach, Veitsrodt, Vollmersbach, Weiden
Hardness range (WRMG) weich Single value · Asbacher Hütte (Harfenmühle), Breitenthal, Herborn, Herrstein, Mörschied, Niederhosenbach, Niederwörresbach, Oberhosenbach, Oberwörresbach, Veitsrodt, Vollmersbach, Weiden
Total hardness 5,5 ° dH Single value · Asbacher Hütte (Harfenmühle), Breitenthal, Herborn, Herrstein, Mörschied, Niederhosenbach, Niederwörresbach, Oberhosenbach, Oberwörresbach, Veitsrodt, Vollmersbach, Weiden

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Bergen, Berschweiler, Dickesbach, Fischbach, Griebelschied, Mittelreidenbach, Oberreidenbach, Schmidthachenbach, Sien, Sienhachenbach, Sonnschied, Wickenrodt

Verbandsgemeindewerke Herrstein-Rhaunen

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
5.6 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Further parameters (3)

Further parameters – Bergen, Berschweiler, Dickesbach, Fischbach, Griebelschied, Mittelreidenbach, Oberreidenbach, Schmidthachenbach, Sien, Sienhachenbach, Sonnschied, Wickenrodt
Parameter Value Parametric value Share of the parametric value Reference
Carbonate hardness 0,73 mmol/l Single value · Bergen, Berschweiler, Dickesbach, Fischbach, Griebelschied, Mittelreidenbach, Oberreidenbach, Schmidthachenbach, Sien, Sienhachenbach, Sonnschied, Wickenrodt
Hardness range (WRMG) weich Single value · Bergen, Berschweiler, Dickesbach, Fischbach, Griebelschied, Mittelreidenbach, Oberreidenbach, Schmidthachenbach, Sien, Sienhachenbach, Sonnschied, Wickenrodt
Total hardness 5,6 ° dH Single value · Bergen, Berschweiler, Dickesbach, Fischbach, Griebelschied, Mittelreidenbach, Oberreidenbach, Schmidthachenbach, Sien, Sienhachenbach, Sonnschied, Wickenrodt

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Bollenbach, Bundenbach, Hausen, Hochwälder Hof, Hottenbach, Hottenbacher Mühle, Oberkirn, Rhaunen, Stipshausen, Sulzbach, Weitersbach

Verbandsgemeindewerke Herrstein-Rhaunen

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
3.3 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Further parameters (3)

Further parameters – Bollenbach, Bundenbach, Hausen, Hochwälder Hof, Hottenbach, Hottenbacher Mühle, Oberkirn, Rhaunen, Stipshausen, Sulzbach, Weitersbach
Parameter Value Parametric value Share of the parametric value Reference
Carbonate hardness 0,44 mmol/l Single value · Bollenbach, Bundenbach, Hausen, Hochwälder Hof, Hottenbach, Hottenbacher Mühle, Oberkirn, Rhaunen, Stipshausen, Sulzbach, Weitersbach
Hardness range (WRMG) weich Single value · Bollenbach, Bundenbach, Hausen, Hochwälder Hof, Hottenbach, Hottenbacher Mühle, Oberkirn, Rhaunen, Stipshausen, Sulzbach, Weitersbach
Total hardness 3,3 ° dH Single value · Bollenbach, Bundenbach, Hausen, Hochwälder Hof, Hottenbach, Hottenbacher Mühle, Oberkirn, Rhaunen, Stipshausen, Sulzbach, Weitersbach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
5.6 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Further parameters (3)

Further parameters – Gerach, Hintertiefenbach
Parameter Value Parametric value Share of the parametric value Reference
Carbonate hardness 0,71 mmol/l Single value · Gerach, Hintertiefenbach
Hardness range (WRMG) weich Single value · Gerach, Hintertiefenbach
Total hardness 5,6 ° dH Single value · Gerach, Hintertiefenbach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Frequent questions about postcode 55758

How hard is the water in Postcode 55758?
TWIST RLP - Steinbachtalsperre publishes a total hardness of 0.8 mmol/l for the supply zone Steinbachtalsperre — that corresponds to 4.5 °dH. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 13/07/2026.
How much nitrate is in the drinking water in Postcode 55758?
TWIST RLP - Steinbachtalsperre publishes a nitrate value of 1.6 mg/L for the supply zone Steinbachtalsperre. The statutory parametric value is 50 mg/l; the measured value represents 3 % of the parametric value. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Are PFAS detectable in the drinking water in Postcode 55758?
TWIST RLP - Steinbachtalsperre publishes for the supply zone Steinbachtalsperre a sum value PFAS-20 of 0 µg/L. The statutory parametric value is 0.1 µg/l; the measured value represents 0 % of the parametric value. For the sum of the 20 individual substances, this parametric value has applied since 12/01/2026. Basis: Publication by the water supplier, retrieved on 13/07/2026.
Who supplies the drinking water in Postcode 55758?
TWIST RLP - Steinbachtalsperre. The values shown here come from the supply zone Steinbachtalsperre and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.