Skip to content
maunawai.info

Drinking water in 51570

For this postcode the responsible water supplier publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 11 underneath. The water supplier publishes 7 further local networks that cannot be clearly assigned to this postcode — they are listed on the water supplier page.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Key values bonn gesamt
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 19 mg/l 50 mg/l
38 %
Maximum · Source [1]
Sodium 17,8 mg/l 200 mg/l
9 %
Maximum · Source [1]
Show all recorded parameters (7 — most recent value per parameter)

Chemical parameters (2)

Chemical parameters – bonn gesamt
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 19 mg/l 50 mg/l
38 %
Maximum · Source [1]
Uranium < 0,0001 mg/l
below limit of quantification
10 µg/l
< 1 % *
Single value · Source [1]

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (2)

Indicator parameters – bonn gesamt
Parameter Value Parametric value Share of the parametric value Reference
Chloride 30 mg/l 250 mg/l
12 %
Maximum · Source [1]
Sodium 17,8 mg/l 200 mg/l
9 %
Maximum · Source [1]

Further parameters (3)

Further parameters – bonn gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 37,9 mg/l Maximum · Source [1]
Magnesium 7,5 mg/l Maximum · Source [1]
Total hardness 4,4 – 7,0 °dH Mean · Source [2]

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Sources: [1] bonn-37fac000.html · 2025 · retrieved on 25/07/2026 [2] https://www.stadtwerke-bonn.de/fuer-zuhause/produkte/wasser/wasseranalyse/ · 2025 · retrieved on 11/07/2026
Show 11 more supply zones in this postcode

Hochbehälter Tomberg Auslauf (Ort 561)

Wahnbachtalsperrenverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 04/08/2025. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Water hardness
5 °dH
Hardness range soft
Key values Hochbehälter Tomberg Auslauf (Ort 561)
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 12 mg/l 50 mg/l
24 %
Single value · 04.08.2025
Lead - mg/l
not determined
10 µg/l Single value · 04.08.2025
Sulphate 26 mg/l 250 mg/l
10 %
Single value · 04.08.2025
Sodium 11,7 mg/l 200 mg/l
6 %
Single value · 04.08.2025
Show all recorded parameters (50 — most recent value per parameter)

Chemical parameters (31)

Chemical parameters – Hochbehälter Tomberg Auslauf (Ort 561)
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane - mg/l
not determined
3 µg/l Single value · 04.08.2025
Acrylamide - mg/l
not determined
0.1 µg/l Single value · 04.08.2025
Antimony - mg/l
not determined
5 µg/l Single value · 04.08.2025
Arsenic - mg/l
not determined
10 µg/l Single value · 04.08.2025
Benzene - mg/l
not determined
1 µg/l Single value · 04.08.2025
Benzo(a)pyrene - mg/l
not determined
10 ng/l Single value · 04.08.2025
Bisphenol A - mg/l
not determined
2.5 µg/l Single value · 04.08.2025
Bromate - mg/l
not determined
10 µg/l Single value · 04.08.2025
Cadmium - mg/l
not determined
3 µg/l Single value · 04.08.2025
Chlorate - mg/l
not determined
70 µg/l Single value · 04.08.2025
Chlorite 0,16 mg/l 0.2 mg/l
80 %
Single value · 04.08.2025
Chromium - mg/l
not determined
25 µg/l Single value · 04.08.2025
Copper - mg/l
not determined
2 mg/l Single value · 04.08.2025
Cyanide - mg/l
not determined
50 µg/l Single value · 04.08.2025
Desethylterbuthylazine - mg/l
not determined
Single value · 04.08.2025
Epichlorohydrin - mg/l
not determined
0.1 µg/l Single value · 04.08.2025
Fluoride 0,06 mg/l 1.5 mg/l
4 %
Single value · 04.08.2025
Lead - mg/l
not determined
10 µg/l Single value · 04.08.2025
MCPA - mg/l
not determined
Single value · 04.08.2025
Mercury - mg/l
not determined
1 µg/l Single value · 04.08.2025
Metolachlor - mg/l
not determined
Single value · 04.08.2025
Nickel - mg/l
not determined
20 µg/l Single value · 04.08.2025
Nitrate 12 mg/l 50 mg/l
24 %
Single value · 04.08.2025
Nitrite <0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value · 04.08.2025
Selenium - mg/l
not determined
10 µg/l Single value · 04.08.2025
Terbuthylazine - mg/l
not determined
Single value · 04.08.2025
Terbutryn - mg/l
not determined
Single value · 04.08.2025
Tetrachloromethane - mg/l
not determined
Single value · 04.08.2025
Trihalomethanes — Total - mg/l
not determined
50 µg/l Single value · 04.08.2025
Uranium - mg/l
not determined
10 µg/l Single value · 04.08.2025
Vinyl chloride - mg/l
not determined
0.5 µg/l Single value · 04.08.2025

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (10)

Indicator parameters – Hochbehälter Tomberg Auslauf (Ort 561)
Parameter Value Parametric value Share of the parametric value Reference
Ammonium <0,02 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value · 04.08.2025
Chloride 21 mg/l 250 mg/l
8 %
Single value · 04.08.2025
Conductivity (25 °C) 25,1 mS/m 2,790 µS/cm Single value · 04.08.2025
Odour ohne TON für den Verbraucher annehmbar Single value · 04.08.2025
Sodium 11,7 mg/l 200 mg/l
6 %
Single value · 04.08.2025
Sulphate 26 mg/l 250 mg/l
10 %
Single value · 04.08.2025
Taste -
not determined
für den Verbraucher annehmbar Single value · 04.08.2025
Temperature 11 °C Single value · 04.08.2025
Total organic carbon (TOC) 0,9 mg/l ohne anormale Veränderung Single value · 04.08.2025
Turbidity <0,10 FNU
below limit of quantification
1 NTU Single value · 04.08.2025

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Treatment substances (1)

Treatment substances – Hochbehälter Tomberg Auslauf (Ort 561)
Parameter Value Parametric value Share of the parametric value Reference
Chlorine dioxide - mg/l
not determined
Single value · 04.08.2025

Further parameters (8)

Further parameters – Hochbehälter Tomberg Auslauf (Ort 561)
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 1,11 mmol/l Single value · 04.08.2025
Calcium 27,3 mg/l Single value · 04.08.2025
Magnesium 5,3 mg/l Single value · 04.08.2025
Oxygen 96 % Single value · 04.08.2025
Phosphate <0,008 mg/l P
below limit of quantification
Single value · 04.08.2025
Potassium 2,2 mg/l Single value · 04.08.2025
Total hardness 0,9 mmol/l Single value · 04.08.2025
Zinc - mg/l
not determined
Single value · 04.08.2025

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.rheinbach.de/fileadmin/user_upload/Rathaus_und_Service/Wasserwerk/2025-09-10_GA_0561_2025_08.pdf · Ausdruck vom 22.08.2025 · 02.09.2024 - 04.08.2025 · retrieved on 08/07/2026

Alle Versorgungsbereiche

Wahnbachtalsperrenverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values Alle Versorgungsbereiche
Parameter Value Parametric value Share of the parametric value Reference
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean · Alle Versorgungsbereiche

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (17 — most recent value per parameter)

Microbiology (1)

Microbiology – Alle Versorgungsbereiche
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 /100ml 0/100 ml Mean · Alle Versorgungsbereiche

Chemical parameters (10)

Chemical parameters – Alle Versorgungsbereiche
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 0,001 mg/l
below limit of quantification
5 µg/l
< 20 % *
Mean · Alle Versorgungsbereiche
Arsenic < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean · Alle Versorgungsbereiche
Benzo(a)pyrene < 0,000005 mg/l
below limit of quantification
10 ng/l
< 50 % *
Mean · Alle Versorgungsbereiche
Cadmium < 0,0003 mg/l
below limit of quantification
3 µg/l
< 10 % *
Mean · Alle Versorgungsbereiche
Chlorite 0,12 ± 0,03 mg/l 0.2 mg/l Mean · Alle Versorgungsbereiche
Copper < 0,010 mg/l
below limit of quantification
2 mg/l
< 0.5 % *
Mean · Alle Versorgungsbereiche
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean · Alle Versorgungsbereiche
Mercury < 0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Mean · Alle Versorgungsbereiche
Nickel < 0,005 mg/l
below limit of quantification
20 µg/l
< 25 % *
Mean · Alle Versorgungsbereiche
Selenium < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean · Alle Versorgungsbereiche

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (6)

Indicator parameters – Alle Versorgungsbereiche
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,005 mg/l
below limit of quantification
0.2 mg/l
< 3 % *
Mean · Alle Versorgungsbereiche
Coliform bacteria 0 /100ml 0/100 ml Mean · Alle Versorgungsbereiche
Colony count 22 °C 0 - 2 /1ml ohne anormale Veränderung Single value · Alle Versorgungsbereiche
Colony count 36 °C 0 - 1 /1ml ohne anormale Veränderung Single value · Alle Versorgungsbereiche
Iron < 0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Mean · Alle Versorgungsbereiche
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean · Alle Versorgungsbereiche

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wahnbach.de/fileadmin/downloadcenter/Trinkwasseranalysen_2025.pdf · Analysenwerte von Januar bis Dezember 2025 (Mittelwerte ± Standardabweichungen aus den monatlichen/regelmäßigen Untersuchungen) · retrieved on 13/07/2026

neunkirchen-seelscheid gesamt

Wahnbachtalsperrenverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values neunkirchen-seelscheid gesamt
Parameter Value Parametric value Share of the parametric value Reference
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (17 — most recent value per parameter)

Microbiology (1)

Microbiology – neunkirchen-seelscheid gesamt
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 /100ml 0/100 ml Single value

Chemical parameters (10)

Chemical parameters – neunkirchen-seelscheid gesamt
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 0,001 mg/l
below limit of quantification
5 µg/l
< 20 % *
Single value
Arsenic < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Benzo(a)pyrene < 0,000005 mg/l
below limit of quantification
10 ng/l
< 50 % *
Single value
Cadmium < 0,0003 mg/l
below limit of quantification
3 µg/l
< 10 % *
Single value
Chlorite 0,12 ± 0,03 mg/l 0.2 mg/l Mean
Copper < 0,010 mg/l
below limit of quantification
2 mg/l
< 0.5 % *
Single value
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Mercury < 0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Nickel < 0,005 mg/l
below limit of quantification
20 µg/l
< 25 % *
Single value
Selenium < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (6)

Indicator parameters – neunkirchen-seelscheid gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,005 mg/l
below limit of quantification
0.2 mg/l
< 3 % *
Single value
Coliform bacteria 0 /100ml 0/100 ml Single value
Colony count 22 °C 0 - 2 /1ml ohne anormale Veränderung Single value
Colony count 36 °C 0 - 1 /1ml ohne anormale Veränderung Single value
Iron < 0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wahnbach.de/fileadmin/downloadcenter/Trinkwasseranalysen_2025.pdf · Januar bis Dezember 2025 · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values siegburg gesamt
Parameter Value Parametric value Share of the parametric value Reference
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (25 — most recent value per parameter)

Microbiology (1)

Microbiology – siegburg gesamt
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 /100ml 0/100 ml Mean

Chemical parameters (18)

Chemical parameters – siegburg gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0005 mg/l
below limit of quantification
3 µg/l
< 17 % *
Mean
Acrylamide <0,00003 mg/l
below limit of quantification
0.1 µg/l
< 30 % *
Mean
Antimony < 0,001 mg/l
below limit of quantification
5 µg/l
< 20 % *
Mean
Arsenic < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Benzene < 0,0005 mg/l
below limit of quantification
1 µg/l
< 50 % *
Mean
Benzo(a)pyrene < 0,000005 mg/l
below limit of quantification
10 ng/l
< 50 % *
Mean
Bisphenol A <0,0005 mg/l
below limit of quantification
2.5 µg/l
< 20 % *
Mean
Cadmium < 0,0003 mg/l
below limit of quantification
3 µg/l
< 10 % *
Mean
Chlorate <0,050 mg/l
below limit of quantification
70 µg/l
< 71 % *
Mean
Chlorite 0,12 ± 0,03 mg/l 0.2 mg/l Mean
Copper < 0,010 mg/l
below limit of quantification
2 mg/l
< 0.5 % *
Mean
Cyanide < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean
Epichlorohydrin <0,00003 mg/l
below limit of quantification
0.1 µg/l
< 30 % *
Mean
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Mercury < 0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Mean
Nickel < 0,005 mg/l
below limit of quantification
20 µg/l
< 25 % *
Mean
Selenium < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Vinyl chloride <0,0005 mg/l
below limit of quantification
0.5 µg/l
< 100 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (6)

Indicator parameters – siegburg gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,005 mg/l
below limit of quantification
0.2 mg/l
< 3 % *
Mean
Coliform bacteria 0 /100ml 0/100 ml Mean
Colony count 22 °C 0 - 2 /1ml ohne anormale Veränderung Mean
Colony count 36 °C 0 - 1 /1ml ohne anormale Veränderung Mean
Iron < 0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Mean
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wahnbach.de/fileadmin/downloadcenter/Trinkwasseranalysen_2025.pdf · Januar bis Dezember 2025 · retrieved on 13/07/2026

Versorgungsbereiche Ost/West II, Mitte, West I (sowie Zuschusswassergebiete)

Wahnbachtalsperrenverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values Versorgungsbereiche Ost/West II, Mitte, West I (sowie Zuschusswassergebiete)
Parameter Value Parametric value Share of the parametric value Reference
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (26 — most recent value per parameter)

Microbiology (1)

Microbiology – Versorgungsbereiche Ost/West II, Mitte, West I (sowie Zuschusswassergebiete)
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 /100ml 0/100 ml Mean

Chemical parameters (19)

Chemical parameters – Versorgungsbereiche Ost/West II, Mitte, West I (sowie Zuschusswassergebiete)
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0005 mg/l
below limit of quantification
3 µg/l
< 17 % *
Mean
Acrylamide <0,00003 mg/l
below limit of quantification
0.1 µg/l
< 30 % *
Mean
Antimony < 0,001 mg/l
below limit of quantification
5 µg/l
< 20 % *
Mean
Arsenic < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Benzene < 0,0005 mg/l
below limit of quantification
1 µg/l
< 50 % *
Mean
Benzo(a)pyrene < 0,000005 mg/l
below limit of quantification
10 ng/l
< 50 % *
Mean
Bisphenol A <0,0005 mg/l
below limit of quantification
2.5 µg/l
< 20 % *
Mean
Cadmium < 0,0003 mg/l
below limit of quantification
3 µg/l
< 10 % *
Mean
Chlorate <0,050 mg/l
below limit of quantification
70 µg/l
< 71 % *
Mean
Chlorite 0,12 ± 0,03 mg/l 0.2 mg/l Mean
Chromium < 0,0005 mg/l
below limit of quantification
25 µg/l
< 2 % *
Mean
Copper < 0,010 mg/l
below limit of quantification
2 mg/l
< 0.5 % *
Mean
Cyanide < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean
Epichlorohydrin <0,00003 mg/l
below limit of quantification
0.1 µg/l
< 30 % *
Mean
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Mercury < 0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Mean
Nickel < 0,005 mg/l
below limit of quantification
20 µg/l
< 25 % *
Mean
Selenium < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Vinyl chloride <0,0005 mg/l
below limit of quantification
0.5 µg/l
< 100 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (6)

Indicator parameters – Versorgungsbereiche Ost/West II, Mitte, West I (sowie Zuschusswassergebiete)
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,005 mg/l
below limit of quantification
0.2 mg/l
< 3 % *
Mean
Coliform bacteria 0 /100ml 0/100 ml Mean
Colony count 22 °C 0 - 2 /1ml ohne anormale Veränderung Single value
Colony count 36 °C 0 - 1 /1ml ohne anormale Veränderung Single value
Iron < 0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Mean
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wahnbach.de/fileadmin/downloadcenter/Trinkwasseranalysen_2025.pdf · Januar bis Dezember 2025 · retrieved on 13/07/2026

ruppichteroth gesamt

Wahnbachtalsperrenverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2024. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Key values ruppichteroth gesamt
Parameter Value Parametric value Share of the parametric value Reference
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (17 — most recent value per parameter)

Microbiology (1)

Microbiology – ruppichteroth gesamt
Parameter Value Parametric value Share of the parametric value Reference
Intestinal enterococci 0 /100ml 0/100 ml Mean

Chemical parameters (11)

Chemical parameters – ruppichteroth gesamt
Parameter Value Parametric value Share of the parametric value Reference
Antimony < 0,001 mg/l
below limit of quantification
5 µg/l
< 20 % *
Mean
Arsenic < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Benzo(a)pyrene < 0,000005 mg/l
below limit of quantification
10 ng/l
< 50 % *
Mean
Cadmium < 0,0006 mg/l
below limit of quantification
3 µg/l
< 20 % *
Mean
Chlorite 0,13 ± 0,04 mg/l 0.2 mg/l Mean
Copper < 0,010 mg/l
below limit of quantification
2 mg/l
< 0.5 % *
Mean
Cyanide < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Mercury < 0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Mean
Nickel < 0,005 mg/l
below limit of quantification
20 µg/l
< 25 % *
Mean
Selenium < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (5)

Indicator parameters – ruppichteroth gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium < 0,005 mg/l
below limit of quantification
0.2 mg/l
< 3 % *
Mean
Colony count 22 °C 0 /1 ml ohne anormale Veränderung Mean
Colony count 36 °C 0 - 2 /1 ml ohne anormale Veränderung Maximum
Iron < 0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Mean
Manganese < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.gemeindewerkeruppichteroth.de/dokumente/wasser/informationen-tw-qualitaet/tw-analyse-jan-dez-2024.pdf · Analysewerte von Januar bis Dezember 2024 · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values Mitte
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 16 ± 3 mg/l 50 mg/l Mean · Mitte
Sulphate 28 ± 1,8 mg/l 250 mg/l Mean · Mitte
Sodium 15,3 ± 2,5 mg/l 200 mg/l Mean · Mitte
Show all recorded parameters (21 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Mitte
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,1 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Mean · Mitte
Nitrate 16 ± 3 mg/l 50 mg/l Mean · Mitte
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Mitte

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Mitte
Parameter Value Parametric value Share of the parametric value Reference
Ammonium < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Mitte
Chloride 26 ± 4 mg/l 250 mg/l Mean · Mitte
Colour 0,01 ± 0,01 m-1 0.5 m⁻¹ Mean · Mitte
Conductivity (25 °C) 32 ± 4 mS/m 2,790 µS/cm Mean · Mitte
Odour ohne für den Verbraucher annehmbar Single value · Mitte
pH 8,0 ± 0,2 6,5–9,5 Mean · Mitte
Sodium 15,3 ± 2,5 mg/l 200 mg/l Mean · Mitte
Sulphate 28 ± 1,8 mg/l 250 mg/l Mean · Mitte
Taste erfüllt für den Verbraucher annehmbar Single value · Mitte
Temperature 10,2 ± 1,3 °C Mean · Mitte
Turbidity < 0,1 FNU
below limit of quantification
1 NTU Mean · Mitte

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Mitte
Parameter Value Parametric value Share of the parametric value Reference
Calcium 33,4 ± 4,5 mg/l Mean · Mitte
Carbonate hardness 3,9 ± 0,7 °dH Mean · Mitte
Magnesium 6,7 ± 0,8 mg/l Mean · Mitte
Phosphate < 0,01 mg/l
below limit of quantification
Mean · Mitte
Potassium 3,0 ± 0,4 mg/l Mean · Mitte
Silicate / silicic acid 4,0 ± 0,7 mg/l Mean · Mitte
Total hardness 1,11 ± 0,15 mmol/l Mean · Mitte

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wahnbach.de/fileadmin/downloadcenter/Trinkwasseranalysen_2025.pdf · Januar bis Dezember 2025 · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values Ost + West II
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 10 ± 1 mg/l 50 mg/l Mean · Ost + West II
Sulphate 25 ± 0,6 mg/l 250 mg/l Mean · Ost + West II
Sodium 10,8 ± 1,0 mg/l 200 mg/l Mean · Ost + West II
Show all recorded parameters (21 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – Ost + West II
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,1 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Mean · Ost + West II
Nitrate 10 ± 1 mg/l 50 mg/l Mean · Ost + West II
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Ost + West II

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – Ost + West II
Parameter Value Parametric value Share of the parametric value Reference
Ammonium < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Mean · Ost + West II
Chloride 20 ± 2 mg/l 250 mg/l Mean · Ost + West II
Colour 0,02 ± 0,01 m-1 0.5 m⁻¹ Mean · Ost + West II
Conductivity (25 °C) 24 ± 2 mS/m 2,790 µS/cm Mean · Ost + West II
Odour ohne für den Verbraucher annehmbar Single value · Ost + West II
pH 8,2 ± 0,1 6,5–9,5 Mean · Ost + West II
Sodium 10,8 ± 1,0 mg/l 200 mg/l Mean · Ost + West II
Sulphate 25 ± 0,6 mg/l 250 mg/l Mean · Ost + West II
Taste erfüllt für den Verbraucher annehmbar Single value · Ost + West II
Temperature 8,8 ± 2,0 °C Mean · Ost + West II
Turbidity < 0,1 FNU
below limit of quantification
1 NTU Mean · Ost + West II

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Ost + West II
Parameter Value Parametric value Share of the parametric value Reference
Calcium 25,3 ± 1,5 mg/l Mean · Ost + West II
Carbonate hardness 2,7 ± 0,4 °dH Mean · Ost + West II
Magnesium 5,2 ± 0,3 mg/l Mean · Ost + West II
Phosphate < 0,01 mg/l
below limit of quantification
Mean · Ost + West II
Potassium 2,1 ± 0,1 mg/l Mean · Ost + West II
Silicate / silicic acid 2,7 ± 0,3 mg/l Mean · Ost + West II
Total hardness 0,85 ± 0,05 mmol/l Mean · Ost + West II

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wahnbach.de/fileadmin/downloadcenter/Trinkwasseranalysen_2025.pdf · Januar bis Dezember 2025 · retrieved on 13/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Key values West I
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 13 ± 2 mg/l 50 mg/l Mean · West I
Sulphate 27 ± 0,8 mg/l 250 mg/l Mean · West I
Sodium 12,7 ± 1,2 mg/l 200 mg/l Mean · West I
Show all recorded parameters (21 — most recent value per parameter)

Chemical parameters (3)

Chemical parameters – West I
Parameter Value Parametric value Share of the parametric value Reference
Fluoride < 0,1 mg/l
below limit of quantification
1.5 mg/l
< 7 % *
Mean · West I
Nitrate 13 ± 2 mg/l 50 mg/l Mean · West I
Nitrite < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Mean · West I

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (11)

Indicator parameters – West I
Parameter Value Parametric value Share of the parametric value Reference
Ammonium < 0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Mean · West I
Chloride 23 ± 2 mg/l 250 mg/l Mean · West I
Colour 0,02 ± 0,01 m-1 0.5 m⁻¹ Mean · West I
Conductivity (25 °C) 27 ± 2 mS/m 2,790 µS/cm Mean · West I
Odour ohne für den Verbraucher annehmbar Single value · West I
pH 8,2 ± 0,2 6,5–9,5 Mean · West I
Sodium 12,7 ± 1,2 mg/l 200 mg/l Mean · West I
Sulphate 27 ± 0,8 mg/l 250 mg/l Mean · West I
Taste erfüllt für den Verbraucher annehmbar Single value · West I
Temperature 9,8 ± 1,4 °C Mean · West I
Turbidity < 0,1 FNU
below limit of quantification
1 NTU Mean · West I

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – West I
Parameter Value Parametric value Share of the parametric value Reference
Calcium 29,2 ± 1,7 mg/l Mean · West I
Carbonate hardness 3,2 ± 0,4 °dH Mean · West I
Magnesium 5,8 ± 0,4 mg/l Mean · West I
Phosphate < 0,01 mg/l
below limit of quantification
Mean · West I
Potassium 2,5 ± 0,2 mg/l Mean · West I
Silicate / silicic acid 3,3 ± 0,4 mg/l Mean · West I
Total hardness 0,97 ± 0,06 mmol/l Mean · West I

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wahnbach.de/fileadmin/downloadcenter/Trinkwasseranalysen_2025.pdf · Januar bis Dezember 2025 · retrieved on 13/07/2026

Wasserwerk Erlenhagen

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.5 °dH
Hardness range soft
Key values Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml Single value
Show all recorded parameters (49 — most recent value per parameter)

Microbiology (2)

Microbiology – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100 ml 0/100 ml Single value
Intestinal enterococci 0 KBE/100 ml 0/100 ml Single value

Chemical parameters (12)

Chemical parameters – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00010 mg/l
below limit of quantification
3 µg/l
< 3 % *
Single value
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Benzo(a)pyrene <0,000010 mg/l
below limit of quantification
10 ng/l
< 100 % *
Single value
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Cyanide <0,0050 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value
Dibromoacetic acid <0,001 mg/l
below limit of quantification
Single value
Dichloroacetic acid 0,0018 mg/l Single value
Monobromoacetic acid <0,001 mg/l
below limit of quantification
Single value
Monochloroacetic acid <0,001 mg/l
below limit of quantification
Single value
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Single value
Trichloroacetic acid <0,001 mg/l
below limit of quantification
Single value
Trihalomethanes — Total 0,0058 mg/l 50 µg/l
12 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (18)

PFAS – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Perfluorobutane sulfonic acid (PFBS) <0,000001 mg/l
below limit of quantification
Single value
Perfluorobutanoic acid (PFBA) <0,000001 mg/l
below limit of quantification
Single value
Perfluorodecanoic acid (PFDA) <0,000001 mg/l
below limit of quantification
Single value
Perfluorododecane sulfonic acid (PFDoDS) <0,000001 mg/l
below limit of quantification
Single value
Perfluorododecanoic acid (PFDoDA) <0,000001 mg/l
below limit of quantification
Single value
Perfluoroheptane sulfonic acid (PFHpS) <0,000001 mg/l
below limit of quantification
Single value
Perfluoroheptanoic acid (PFHpA) <0,000001 mg/l
below limit of quantification
Single value
Perfluorohexane sulfonic acid (PFHxS) <0,000001 mg/l
below limit of quantification
Single value
Perfluorohexanoic acid (PFHxA) <0,000001 mg/l
below limit of quantification
Single value
Perfluorononane sulfonic acid (PFNS) <0,000001 mg/l
below limit of quantification
Single value
Perfluorononanoic acid (PFNA) <0,000001 mg/l
below limit of quantification
Single value
Perfluorooctanesulfonic acid (PFOS) <0,000001 mg/l
below limit of quantification
Single value
Perfluorooctanoic acid (PFOA) <0,000001 mg/l
below limit of quantification
Single value
Perfluoropentanesulfonic acid (PFPeS) <0,000001 mg/l
below limit of quantification
Single value
Perfluoropentanoic acid (PFPeA) <0,000001 mg/l
below limit of quantification
Single value
Perfluorotridecanesulfonic acid (PFTrDS) <0,000001 mg/l
below limit of quantification
Single value
Perfluorotridecanoic acid (PFTrDA) <0,000001 mg/l
below limit of quantification
Single value
Perfluoroundecanoic acid (PFUnDA) <0,000001 mg/l
below limit of quantification
Single value

Indicator parameters (15)

Indicator parameters – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Ammonium <0,13 mg/l
below limit of quantification
0.5 mg/l
< 26 % *
Single value
Clostridium perfringens (including spores) 0 KBE/100 ml 0/100 ml Single value
Coliform bacteria 0 MPN/100 ml 0/100 ml Single value
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Single value
Iron 0,020 mg/l 0.2 mg/l
10 %
Single value
Manganese <0,0050 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value
Odour kein ungewöhnlicher Geruch für den Verbraucher annehmbar Single value
pH 8,2 6,5–9,5 Single value
Taste o.B. für den Verbraucher annehmbar Single value
Temperature 5,5 °C Single value
Threshold odour number (TON) <1 TON
below limit of quantification
Single value
Total organic carbon (TOC) 2,5 mg/l ohne anormale Veränderung Single value
Turbidity 0,05 NTU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (2)

Further parameters – Wasserwerk Erlenhagen
Parameter Value Parametric value Share of the parametric value Reference
Copper quotient 9,2 Single value
Total hardness 4,5 °dH Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

bergneustadt gesamt

Aggerverband

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
4.4 °dH
Hardness range soft
Key values bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (61 — most recent value per parameter)

Microbiology (3)

Microbiology – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100 ml 0/100 ml Mean
Intestinal enterococci 0 KBE/100 ml 0/100 ml Mean
Somatic coliphages <2 PFU/100 ml
below limit of quantification
50/100 ml
UBA guide value
Mean

For trifluoroacetic acid (TFA), the German Drinking Water Ordinance does not specify a parametric value. The comparison is therefore made with the guide value of 60 µg/l issued by the Umweltbundesamt, which has replaced the earlier health-related guidance value of 3 µg/l. A guide value is not a legal maximum but a health-related classification.

Chemical parameters (25)

Chemical parameters – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0001 mg/l
below limit of quantification
3 µg/l
< 3 % *
Mean
Antimony <0,0001 mg/l
below limit of quantification
5 µg/l
< 2 % *
Mean
Arsenic <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Benzene <0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Mean
Benzo(a)pyrene <0,00001 mg/l
below limit of quantification
10 ng/l
< 100 % *
Mean
Bisphenol A <0,00003 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Mean
Boron 0,008 mg/l 1 mg/l
0.8 %
Mean
Bromate <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Cadmium <0,0001 mg/l
below limit of quantification
3 µg/l
< 3 % *
Mean
Chromium <0,0005 mg/l
below limit of quantification
25 µg/l
< 2 % *
Mean
Copper <0,005 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Mean
Cyanide <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean
Fluoride <0,05 mg/l
below limit of quantification
1.5 mg/l
< 3 % *
Mean
Haloacetic acids (HAA) <0,0060 mg/l
below limit of quantification
Mean
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Mercury <0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Mean
Microcystin-LR <0,00005 mg/l
below limit of quantification
Mean
Nickel <0,001 mg/l
below limit of quantification
20 µg/l
< 5 % *
Mean
Nitrate 6,8 mg/l 50 mg/l
14 %
Mean
Nitrite <0,01 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Mean
Polycyclic aromatic hydrocarbons 0 mg/l 0.1 µg/l
0 %
Mean
Selenium <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Mean
Trihalomethanes — Total 0,005 mg/l 50 µg/l
10 %
Mean
Uranium <0,0001 mg/l
below limit of quantification
10 µg/l
< 1 % *
Mean
Vinyl chloride <0,0001 mg/l
below limit of quantification
0.5 µg/l
< 20 % *
Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (1)

PFAS – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0 mg/l Mean

Indicator parameters (21)

Indicator parameters – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,010 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Mean
Ammonium <0,13 mg/l
below limit of quantification
0.5 mg/l
< 26 % *
Mean
Calcite dissolution capacity 0,37 mg/l 5 mg/l CaCO3 Mean
Chloride 12,1 mg/l 250 mg/l
5 %
Mean
Clostridium perfringens (including spores) 0 Anzahl/100 ml 0/100 ml Mean
Coliform bacteria 0 Anzahl/100 ml 0/100 ml Mean
Colony count 22 °C <1 KBE/ml
below limit of quantification
ohne anormale Veränderung Mean
Colony count 36 °C <1 KBE/ml
below limit of quantification
ohne anormale Veränderung Mean
Colour <0,1 m-1
below limit of quantification
0.5 m⁻¹ Mean
Conductivity (25 °C) 196 µS/cm 2,790 µS/cm Mean
Iron 0,015 mg/l 0.2 mg/l
8 %
Mean
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Mean
Odour ohne Befund für den Verbraucher annehmbar Mean
Oxidisability <0,5 mg/l
below limit of quantification
5 mg/l O2 Mean
pH 8,2 pH-Einheiten 6,5–9,5 Mean
Sodium 5,4 mg/l 200 mg/l
3 %
Mean
Sulphate 11,8 mg/l 250 mg/l
5 %
Mean
Taste ohne Befund für den Verbraucher annehmbar Mean
Temperature 13,4 °C Maximum
Total organic carbon (TOC) 1,1 mg/l ohne anormale Veränderung Mean
Turbidity 0,05 NTU 1 NTU Mean

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Radiology (1)

Radiology – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Radon-222 <10 Bq/l
below limit of quantification
100 Bq/l Single value

Further parameters (10)

Further parameters – bergneustadt gesamt
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l Mean
Carbonate hardness 3,5 °dH Mean
Copper quotient 10,1 Mean
Lithium <0,10 mg/l
below limit of quantification
Mean
Magnesium 2,7 mg/l Mean
Phosphate <0,03 mg/l
below limit of quantification
Mean
Potassium <1,0 mg/l
below limit of quantification
Mean
Silicate / silicic acid 3,1 mg/l Mean
Total hardness 0,78 mmol/l Mean
Zinc <0,005 mg/l
below limit of quantification
Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Frequent questions about postcode 51570

How much nitrate is in the drinking water in Postcode 51570?
SWB Energie und Wasser (Stadtwerke Bonn); Wasserlieferant: Wahnbachtalsperrenverband (WTV) publishes a nitrate value of 19 mg/l for the supply zone bonn gesamt. The statutory parametric value is 50 mg/l; the measured value represents 38 % of the parametric value. Basis: Publication by the water supplier, retrieved on 25/07/2026.
Who supplies the drinking water in Postcode 51570?
SWB Energie und Wasser (Stadtwerke Bonn); Wasserlieferant: Wahnbachtalsperrenverband (WTV). The values shown here come from the supply zone bonn gesamt and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.