Skip to content
maunawai.info

Drinking water in 16567

For this postcode the responsible water supplier publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 11 underneath.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
Hardness range 13,1
Key values Prenden
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS < 0,000005 mg/l
below limit of quantification
Single value
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 KBE/100 ml 0/100 ml Single value
Sodium 15,6 mg/l 200 mg/l
8 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (91 — most recent value per parameter)

Microbiology (2)

Microbiology – Prenden
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 KBE/100 ml 0/100 ml Single value
Intestinal enterococci 0 KBE/100 ml 0/100 ml Single value

Chemical parameters (51)

Chemical parameters – Prenden
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane < 0,0003 mg/l
below limit of quantification
3 µg/l
< 10 % *
Single value
1,2-Dichloropropane < 0,0001 mg/l
below limit of quantification
Single value
Acrylamide < 0,00005 mg/l
below limit of quantification
0.1 µg/l
< 50 % *
Single value
AMPA < 0,00005 mg/l
below limit of quantification
Single value
Antimony < 0,0005 mg/l
below limit of quantification
5 µg/l
< 10 % *
Single value
Arsenic < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Atrazine < 0,00005 mg/l
below limit of quantification
Single value
Bentazone < 0,00005 mg/l
below limit of quantification
Single value
Benzene < 0,0003 mg/l
below limit of quantification
1 µg/l
< 30 % *
Single value
Benzo(a)pyrene < 0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Benzo(b)fluoranthene < 0,000003 mg/l
below limit of quantification
Single value
Benzo(ghi)perylene < 0,000003 mg/l
below limit of quantification
Single value
Benzo(k)fluoranthene < 0,000003 mg/l
below limit of quantification
Single value
Bisphenol A < 0,0001 mg/l
below limit of quantification
2.5 µg/l
< 4 % *
Single value
Boron 0,024 mg/l 1 mg/l
2 %
Single value
Bromacil < 0,00005 mg/l
below limit of quantification
Single value
Bromate < 0,003 mg/l
below limit of quantification
10 µg/l
< 30 % *
Single value
Bromodichloromethane < 0,0001 mg/l
below limit of quantification
Single value
Cadmium < 0,0005 mg/l
below limit of quantification
3 µg/l
< 17 % *
Single value
Chromium < 0,0005 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper 0,002 mg/l 2 mg/l
0.1 %
Single value
Cyanide < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value
Desethylatrazine < 0,00005 mg/l
below limit of quantification
Single value
Desisopropylatrazine < 0,00005 mg/l
below limit of quantification
Single value
Dibromochloromethane < 0,0001 mg/l
below limit of quantification
Single value
Diuron < 0,00005 mg/l
below limit of quantification
Single value
Epichlorohydrin < 0,00005 mg/l
below limit of quantification
0.1 µg/l
< 50 % *
Single value
Ethidimuron < 0,00005 mg/l
below limit of quantification
Single value
Glyphosate < 0,00005 mg/l
below limit of quantification
Single value
Hexazinone < 0,00005 mg/l
below limit of quantification
Single value
Isoproturon < 0,00005 mg/l
below limit of quantification
Single value
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
MCPA < 0,00005 mg/l
below limit of quantification
Single value
Mecoprop < 0,00005 mg/l
below limit of quantification
Single value
Mercury < 0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Metalaxyl < 0,00005 mg/l
below limit of quantification
Single value
Metazachlor < 0,00005 mg/l
below limit of quantification
Single value
Metazachlor acid < 0,00005 mg/l
below limit of quantification
Single value
Metolachlor < 0,00005 mg/l
below limit of quantification
Single value
Nickel < 0,001 mg/l
below limit of quantification
20 µg/l
< 5 % *
Single value
Pesticides — Total < 0,00005 mg/l
below limit of quantification
0.5 µg/l
< 10 % *
Single value
Selenium < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Simazine < 0,00005 mg/l
below limit of quantification
Single value
Terbuthylazine < 0,00005 mg/l
below limit of quantification
Single value
Tetrachloroethene < 0,0001 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) < 0,0001 mg/l
below limit of quantification
Single value
Trichloroethene < 0,0001 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) < 0,0001 mg/l
below limit of quantification
Single value
Trihalomethanes — Total < 0,0001 mg/l
below limit of quantification
50 µg/l
< 0.2 % *
Single value
Uranium < 0,0002 mg/l
below limit of quantification
10 µg/l
< 2 % *
Single value
Vinyl chloride < 0,0005 mg/l
below limit of quantification
0.5 µg/l
< 100 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (16)

PFAS – Prenden
Parameter Value Parametric value Share of the parametric value Reference
Perfluorobutane sulfonic acid (PFBS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorobutanoic acid (PFBA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorodecane sulfonic acid (PFDS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorododecane sulfonic acid (PFDoDS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoroheptane sulfonic acid (PFHpS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoroheptanoic acid (PFHpA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorohexane sulfonic acid (PFHxS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorohexanoic acid (PFHxA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorononane sulfonic acid (PFNS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorononanoic acid (PFNA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorooctanesulfonic acid (PFOS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorooctanoic acid (PFOA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoropentanesulfonic acid (PFPeS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoropentanoic acid (PFPeA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorotridecanesulfonic acid (PFTrDS) < 0,000005 mg/l
below limit of quantification
Single value
Sum of PFAS < 0,000005 mg/l
below limit of quantification
Single value

Indicator parameters (16)

Indicator parameters – Prenden
Parameter Value Parametric value Share of the parametric value Reference
Ammonium 0,08 mg/l 0.5 mg/l
16 %
Single value
Calcite dissolution capacity mg/l 5 mg/l CaCO3 Single value
Coliform bacteria 0 KBE/100 ml 0/100 ml Single value
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Single value
Colour 0,2 1/m 0.5 m⁻¹ Single value
Conductivity (25 °C) 495 µS/cm 2,790 µS/cm Single value
Iron 0,003 mg/l 0.2 mg/l
2 %
Single value
Manganese 0,014 mg/l 50 µg/l
28 %
Single value
Odour ohne für den Verbraucher annehmbar Single value
pH 7,28 6,5–9,5 Single value
Sodium 15,6 mg/l 200 mg/l
8 %
Single value
Taste ohne für den Verbraucher annehmbar Single value
Temperature 9,8 °C Single value
Total organic carbon (TOC) 2,8 mg/l ohne anormale Veränderung Single value
Turbidity 0,02 NTU 1 NTU Single value

Further parameters (6)

Further parameters – Prenden
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 4 mmol/l Single value
Base capacity to pH 8.2 0,42 mmol/l Single value
Hardness range (WRMG) 2,34 mmol/l Single value
Magnesium 7,06 mg/l Single value
Potassium 1,28 mg/l Single value
Saturation index -0,129 Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://nwa-zehlendorf.de/upload/wasserqualitaet/TW-%20Analyse%20WW%20Prenden%202025%20f%C3%BCr%20homepage.pdf · Prüfzeitraum 27.11.2025 – 17.12.2025 · retrieved on 11/07/2026
Show 11 more supply zones in this postcode

Wasserwerk Basdorf, Anlage Basdorf OT Waldsiedlung

Niederbarnimer Wasser- und Abwasserzweckverband (NWA)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
Hardness range 7,4
Key values Wasserwerk Basdorf, Anlage Basdorf OT Waldsiedlung
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS < 0,000005 mg/l
below limit of quantification
Single value
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 KBE/100 ml 0/100 ml Single value
Sodium 5,87 mg/l 200 mg/l
3 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (91 — most recent value per parameter)

Microbiology (2)

Microbiology – Wasserwerk Basdorf, Anlage Basdorf OT Waldsiedlung
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 KBE/100 ml 0/100 ml Single value
Intestinal enterococci 0 KBE/100 ml 0/100 ml Single value

Chemical parameters (51)

Chemical parameters – Wasserwerk Basdorf, Anlage Basdorf OT Waldsiedlung
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane < 0,0003 mg/l
below limit of quantification
3 µg/l
< 10 % *
Single value
1,2-Dichloropropane < 0,0001 mg/l
below limit of quantification
Single value
Acrylamide < 0,00005 mg/l
below limit of quantification
0.1 µg/l
< 50 % *
Single value
AMPA < 0,00005 mg/l
below limit of quantification
Single value
Antimony < 0,0005 mg/l
below limit of quantification
5 µg/l
< 10 % *
Single value
Arsenic < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Atrazine < 0,00005 mg/l
below limit of quantification
Single value
Bentazone < 0,00005 mg/l
below limit of quantification
Single value
Benzene < 0,0003 mg/l
below limit of quantification
1 µg/l
< 30 % *
Single value
Benzo(a)pyrene < 0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Benzo(b)fluoranthene < 0,000003 mg/l
below limit of quantification
Single value
Benzo(ghi)perylene < 0,000003 mg/l
below limit of quantification
Single value
Benzo(k)fluoranthene < 0,000003 mg/l
below limit of quantification
Single value
Bisphenol A < 0,0001 mg/l
below limit of quantification
2.5 µg/l
< 4 % *
Single value
Boron 0,045 mg/l 1 mg/l
5 %
Single value
Bromacil < 0,00005 mg/l
below limit of quantification
Single value
Bromate < 0,003 mg/l
below limit of quantification
10 µg/l
< 30 % *
Single value
Bromodichloromethane < 0,0001 mg/l
below limit of quantification
Single value
Cadmium < 0,0005 mg/l
below limit of quantification
3 µg/l
< 17 % *
Single value
Chromium < 0,0005 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper 0,001 mg/l 2 mg/l
< 0.1 %
Single value
Cyanide < 0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Single value
Desethylatrazine < 0,00005 mg/l
below limit of quantification
Single value
Desisopropylatrazine < 0,00005 mg/l
below limit of quantification
Single value
Dibromochloromethane < 0,0001 mg/l
below limit of quantification
Single value
Diuron < 0,00005 mg/l
below limit of quantification
Single value
Epichlorohydrin < 0,00005 mg/l
below limit of quantification
0.1 µg/l
< 50 % *
Single value
Ethidimuron < 0,00005 mg/l
below limit of quantification
Single value
Glyphosate < 0,00005 mg/l
below limit of quantification
Single value
Hexazinone < 0,00005 mg/l
below limit of quantification
Single value
Isoproturon < 0,00005 mg/l
below limit of quantification
Single value
Lead < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
MCPA < 0,00005 mg/l
below limit of quantification
Single value
Mecoprop < 0,00005 mg/l
below limit of quantification
Single value
Mercury < 0,0001 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Metalaxyl < 0,00005 mg/l
below limit of quantification
Single value
Metazachlor < 0,00005 mg/l
below limit of quantification
Single value
Metazachlor acid < 0,00005 mg/l
below limit of quantification
Single value
Metolachlor < 0,00005 mg/l
below limit of quantification
Single value
Nickel < 0,001 mg/l
below limit of quantification
20 µg/l
< 5 % *
Single value
Pesticides — Total < 0,00005 mg/l
below limit of quantification
0.5 µg/l
< 10 % *
Single value
Selenium < 0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Simazine < 0,00005 mg/l
below limit of quantification
Single value
Terbuthylazine < 0,00005 mg/l
below limit of quantification
Single value
Tetrachloroethene < 0,0001 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) < 0,0001 mg/l
below limit of quantification
Single value
Trichloroethene < 0,0001 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) < 0,0001 mg/l
below limit of quantification
Single value
Trihalomethanes — Total < 0,0001 mg/l
below limit of quantification
50 µg/l
< 0.2 % *
Single value
Uranium < 0,0002 mg/l
below limit of quantification
10 µg/l
< 2 % *
Single value
Vinyl chloride < 0,0005 mg/l
below limit of quantification
0.5 µg/l
< 100 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (16)

PFAS – Wasserwerk Basdorf, Anlage Basdorf OT Waldsiedlung
Parameter Value Parametric value Share of the parametric value Reference
Perfluorobutane sulfonic acid (PFBS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorobutanoic acid (PFBA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorodecane sulfonic acid (PFDS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorododecane sulfonic acid (PFDoDS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoroheptane sulfonic acid (PFHpS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoroheptanoic acid (PFHpA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorohexane sulfonic acid (PFHxS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorohexanoic acid (PFHxA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorononane sulfonic acid (PFNS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorononanoic acid (PFNA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorooctanesulfonic acid (PFOS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorooctanoic acid (PFOA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoropentanesulfonic acid (PFPeS) < 0,000005 mg/l
below limit of quantification
Single value
Perfluoropentanoic acid (PFPeA) < 0,000005 mg/l
below limit of quantification
Single value
Perfluorotridecanesulfonic acid (PFTrDS) < 0,000005 mg/l
below limit of quantification
Single value
Sum of PFAS < 0,000005 mg/l
below limit of quantification
Single value

Indicator parameters (16)

Indicator parameters – Wasserwerk Basdorf, Anlage Basdorf OT Waldsiedlung
Parameter Value Parametric value Share of the parametric value Reference
Ammonium < 0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Single value
Calcite dissolution capacity 14* mg/l 5 mg/l CaCO3 Single value
Coliform bacteria 0 KBE/100 ml 0/100 ml Single value
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Single value
Colony count 36 °C 1 KBE/ml ohne anormale Veränderung Single value
Colour 0,2 1/m 0.5 m⁻¹ Single value
Conductivity (25 °C) 287 µS/cm 2,790 µS/cm Single value
Iron 0,005 mg/l 0.2 mg/l
3 %
Single value
Manganese 0,009 mg/l 50 µg/l
18 %
Single value
Odour ohne für den Verbraucher annehmbar Single value
pH 7,39 6,5–9,5 Single value
Sodium 5,87 mg/l 200 mg/l
3 %
Single value
Taste ohne für den Verbraucher annehmbar Single value
Temperature 10,2 °C Single value
Total organic carbon (TOC) 2,8 mg/l ohne anormale Veränderung Single value
Turbidity 0,02 NTU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (6)

Further parameters – Wasserwerk Basdorf, Anlage Basdorf OT Waldsiedlung
Parameter Value Parametric value Share of the parametric value Reference
Acid capacity to pH 4.3 2,81 mmol/l Single value
Base capacity to pH 8.2 0,18 mmol/l Single value
Hardness range (WRMG) 1,32 mmol/l Single value
Magnesium 5,82 mg/l Single value
Potassium 1,38 mg/l Single value
Saturation index -0,381 Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://nwa-zehlendorf.de/upload/downloads/analysen/Basdorf%202025.pdf · Prüfzeitraum 26.11.2025 – 17.12.2025 (Probennahme 26.11.2025, 09:15) · retrieved on 11/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
17 °dH
Hardness range hart / hard
Key values Beelitzhof
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,0000099 mg/l Median · Beelitzhof
Nitrate 3,94 mg/l 50 mg/l
8 %
Median · Beelitzhof
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Beelitzhof
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Beelitzhof
Sulphate 101 mg/l 250 mg/l
40 %
Median · Beelitzhof
Sodium 49 mg/l 200 mg/l
25 %
Median · Beelitzhof

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Beelitzhof
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Beelitzhof
Intestinal enterococci 0 /100ml 0/100 ml Median · Beelitzhof

Chemical parameters (23)

Chemical parameters – Beelitzhof
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Beelitzhof
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Beelitzhof
Arsenic <0,00030 mg/l
below limit of quantification
10 µg/l
< 3 % *
Median · Beelitzhof
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Beelitzhof
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Beelitzhof
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Beelitzhof
Boron 0,068 mg/l 1 mg/l
7 %
Median · Beelitzhof
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Beelitzhof
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Beelitzhof
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Beelitzhof
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Beelitzhof
Fluoride 0,21 mg/l 1.5 mg/l
14 %
Median · Beelitzhof
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Beelitzhof
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Beelitzhof
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Beelitzhof
Nitrate 3,94 mg/l 50 mg/l
8 %
Median · Beelitzhof
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Beelitzhof
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Beelitzhof
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Beelitzhof
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Beelitzhof
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Beelitzhof
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Beelitzhof
Uranium 0,0001 mg/l 10 µg/l
1 %
Median · Beelitzhof

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Beelitzhof
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,0000049 mg/l Median · Beelitzhof
Sum of PFAS 0,0000099 mg/l Median · Beelitzhof

Indicator parameters (17)

Indicator parameters – Beelitzhof
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Beelitzhof
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Beelitzhof
Chloride 69 mg/l 250 mg/l
28 %
Median · Beelitzhof
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Beelitzhof
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Beelitzhof
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Median · Beelitzhof
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Beelitzhof
Colour 0,2 1/m 0.5 m⁻¹ Median · Beelitzhof
Conductivity (25 °C) 800 µS/cm 2,790 µS/cm Median · Beelitzhof
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Beelitzhof
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Beelitzhof
pH 7,5 - 6,5–9,5 Median · Beelitzhof
Sodium 49 mg/l 200 mg/l
25 %
Median · Beelitzhof
Sulphate 101 mg/l 250 mg/l
40 %
Median · Beelitzhof
Temperature 12,3 °C Median · Beelitzhof
Total organic carbon (TOC) 3,3 mg/l ohne anormale Veränderung Median · Beelitzhof
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Beelitzhof

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Beelitzhof
Parameter Value Parametric value Share of the parametric value Reference
Calcium 106 mg/l Median · Beelitzhof
Carbonate hardness 11,4 °dH Median · Beelitzhof
Hardness range (WRMG) hart / hard - Median · Beelitzhof
Magnesium 9,4 mg/l Median · Beelitzhof
Oxygen 8,5 mg/l Median · Beelitzhof
Potassium 3,8 mg/l Median · Beelitzhof
Total hardness 17,0 °dH Median · Beelitzhof

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
20.3 °dH
Hardness range hart / hard
Key values Friedrichshagen
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,0000039 mg/l Median · Friedrichshagen
Nitrate 4,38 mg/l 50 mg/l
9 %
Median · Friedrichshagen
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Friedrichshagen
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Friedrichshagen
Sulphate 175 mg/l 250 mg/l
70 %
Median · Friedrichshagen
Sodium 42 mg/l 200 mg/l
21 %
Median · Friedrichshagen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Friedrichshagen
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Friedrichshagen
Intestinal enterococci 0 /100ml 0/100 ml Median · Friedrichshagen

Chemical parameters (23)

Chemical parameters – Friedrichshagen
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Friedrichshagen
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Friedrichshagen
Arsenic 0,00032 mg/l 10 µg/l
3 %
Median · Friedrichshagen
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Friedrichshagen
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Friedrichshagen
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Friedrichshagen
Boron 0,072 mg/l 1 mg/l
7 %
Median · Friedrichshagen
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Friedrichshagen
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Friedrichshagen
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Friedrichshagen
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Friedrichshagen
Fluoride 0,19 mg/l 1.5 mg/l
13 %
Median · Friedrichshagen
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Friedrichshagen
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Friedrichshagen
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Friedrichshagen
Nitrate 4,38 mg/l 50 mg/l
9 %
Median · Friedrichshagen
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Friedrichshagen
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Friedrichshagen
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Friedrichshagen
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Friedrichshagen
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Friedrichshagen
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Friedrichshagen
Uranium 0,0002 mg/l 10 µg/l
2 %
Median · Friedrichshagen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Friedrichshagen
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,0000019 mg/l Median · Friedrichshagen
Sum of PFAS 0,0000039 mg/l Median · Friedrichshagen

Indicator parameters (17)

Indicator parameters – Friedrichshagen
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Friedrichshagen
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Friedrichshagen
Chloride 65 mg/l 250 mg/l
26 %
Median · Friedrichshagen
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Friedrichshagen
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Friedrichshagen
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Median · Friedrichshagen
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Friedrichshagen
Colour 0,2 1/m 0.5 m⁻¹ Median · Friedrichshagen
Conductivity (25 °C) 880 µS/cm 2,790 µS/cm Median · Friedrichshagen
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Friedrichshagen
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Friedrichshagen
pH 7,4 - 6,5–9,5 Median · Friedrichshagen
Sodium 42 mg/l 200 mg/l
21 %
Median · Friedrichshagen
Sulphate 175 mg/l 250 mg/l
70 %
Median · Friedrichshagen
Temperature 11,5 °C Median · Friedrichshagen
Total organic carbon (TOC) 3,7 mg/l ohne anormale Veränderung Median · Friedrichshagen
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Friedrichshagen

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Friedrichshagen
Parameter Value Parametric value Share of the parametric value Reference
Calcium 122 mg/l Median · Friedrichshagen
Carbonate hardness 9,6 °dH Median · Friedrichshagen
Hardness range (WRMG) hart / hard - Median · Friedrichshagen
Magnesium 13,6 mg/l Median · Friedrichshagen
Oxygen 9,6 mg/l Median · Friedrichshagen
Potassium 5,6 mg/l Median · Friedrichshagen
Total hardness 20,3 °dH Median · Friedrichshagen

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
20 °dH
Hardness range hart / hard
Key values Kaulsdorf
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,0000019 mg/l Median · Kaulsdorf
Nitrate 1,92 mg/l 50 mg/l
4 %
Median · Kaulsdorf
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Kaulsdorf
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Kaulsdorf
Sulphate 112 mg/l 250 mg/l
45 %
Median · Kaulsdorf
Sodium 24 mg/l 200 mg/l
12 %
Median · Kaulsdorf

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Kaulsdorf
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Kaulsdorf
Intestinal enterococci 0 /100ml 0/100 ml Median · Kaulsdorf

Chemical parameters (23)

Chemical parameters – Kaulsdorf
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Kaulsdorf
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Kaulsdorf
Arsenic <0,00030 mg/l
below limit of quantification
10 µg/l
< 3 % *
Median · Kaulsdorf
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Kaulsdorf
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Kaulsdorf
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Kaulsdorf
Boron 0,055 mg/l 1 mg/l
6 %
Median · Kaulsdorf
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Kaulsdorf
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Kaulsdorf
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Kaulsdorf
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Kaulsdorf
Fluoride 0,21 mg/l 1.5 mg/l
14 %
Median · Kaulsdorf
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Kaulsdorf
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Kaulsdorf
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Kaulsdorf
Nitrate 1,92 mg/l 50 mg/l
4 %
Median · Kaulsdorf
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Kaulsdorf
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Kaulsdorf
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Kaulsdorf
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Kaulsdorf
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Kaulsdorf
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Kaulsdorf
Uranium 0,0004 mg/l 10 µg/l
4 %
Median · Kaulsdorf

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Kaulsdorf
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS -/- mg/l
not detectable
Median · Kaulsdorf
Sum of PFAS 0,0000019 mg/l Median · Kaulsdorf

Indicator parameters (17)

Indicator parameters – Kaulsdorf
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Kaulsdorf
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Kaulsdorf
Chloride 50 mg/l 250 mg/l
20 %
Median · Kaulsdorf
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Kaulsdorf
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Kaulsdorf
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Median · Kaulsdorf
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Kaulsdorf
Colour <0,2 1/m
below limit of quantification
0.5 m⁻¹ Median · Kaulsdorf
Conductivity (25 °C) 780 µS/cm 2,790 µS/cm Median · Kaulsdorf
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Kaulsdorf
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Kaulsdorf
pH 7,3 - 6,5–9,5 Median · Kaulsdorf
Sodium 24 mg/l 200 mg/l
12 %
Median · Kaulsdorf
Sulphate 112 mg/l 250 mg/l
45 %
Median · Kaulsdorf
Temperature 12,1 °C Median · Kaulsdorf
Total organic carbon (TOC) 2,4 mg/l ohne anormale Veränderung Median · Kaulsdorf
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Kaulsdorf

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Kaulsdorf
Parameter Value Parametric value Share of the parametric value Reference
Calcium 121 mg/l Median · Kaulsdorf
Carbonate hardness 12,4 °dH Median · Kaulsdorf
Hardness range (WRMG) hart / hard - Median · Kaulsdorf
Magnesium 13,8 mg/l Median · Kaulsdorf
Oxygen 7,2 mg/l Median · Kaulsdorf
Potassium 4,9 mg/l Median · Kaulsdorf
Total hardness 20,0 °dH Median · Kaulsdorf

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
18.4 °dH
Hardness range hart / hard
Key values Kladow
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,000016 mg/l Median · Kladow
Nitrate 3,13 mg/l 50 mg/l
6 %
Median · Kladow
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Kladow
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Kladow
Sulphate 120 mg/l 250 mg/l
48 %
Median · Kladow
Sodium 41 mg/l 200 mg/l
21 %
Median · Kladow

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Kladow
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Kladow
Intestinal enterococci 0 /100ml 0/100 ml Median · Kladow

Chemical parameters (23)

Chemical parameters – Kladow
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Kladow
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Kladow
Arsenic <0,00030 mg/l
below limit of quantification
10 µg/l
< 3 % *
Median · Kladow
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Kladow
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Kladow
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Kladow
Boron 0,062 mg/l 1 mg/l
6 %
Median · Kladow
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Kladow
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Kladow
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Kladow
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Kladow
Fluoride 0,18 mg/l 1.5 mg/l
12 %
Median · Kladow
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Kladow
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Kladow
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Kladow
Nitrate 3,13 mg/l 50 mg/l
6 %
Median · Kladow
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Kladow
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Kladow
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Kladow
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Kladow
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Kladow
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Kladow
Uranium <0,00005 mg/l
below limit of quantification
10 µg/l
< 0.5 % *
Median · Kladow

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Kladow
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,0000076 mg/l Median · Kladow
Sum of PFAS 0,000016 mg/l Median · Kladow

Indicator parameters (17)

Indicator parameters – Kladow
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Kladow
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Kladow
Chloride 56 mg/l 250 mg/l
22 %
Median · Kladow
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Kladow
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Kladow
Colony count 22 °C 1 KBE/ml ohne anormale Veränderung Median · Kladow
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Kladow
Colour 0,2 1/m 0.5 m⁻¹ Median · Kladow
Conductivity (25 °C) 790 µS/cm 2,790 µS/cm Median · Kladow
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Kladow
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Kladow
pH 7,5 - 6,5–9,5 Median · Kladow
Sodium 41 mg/l 200 mg/l
21 %
Median · Kladow
Sulphate 120 mg/l 250 mg/l
48 %
Median · Kladow
Temperature 12,2 °C Median · Kladow
Total organic carbon (TOC) 3,5 mg/l ohne anormale Veränderung Median · Kladow
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Kladow

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Kladow
Parameter Value Parametric value Share of the parametric value Reference
Calcium 113 mg/l Median · Kladow
Carbonate hardness 11,2 °dH Median · Kladow
Hardness range (WRMG) hart / hard - Median · Kladow
Magnesium 9,8 mg/l Median · Kladow
Oxygen 7,9 mg/l Median · Kladow
Potassium 3,7 mg/l Median · Kladow
Total hardness 18,4 °dH Median · Kladow

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
15.1 °dH
Hardness range hart / hard
Key values Spandau
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,0000035 mg/l Median · Spandau
Nitrate 1,09 mg/l 50 mg/l
2 %
Median · Spandau
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Spandau
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Spandau
Sulphate 66 mg/l 250 mg/l
26 %
Median · Spandau
Sodium 30 mg/l 200 mg/l
15 %
Median · Spandau

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Spandau
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Spandau
Intestinal enterococci 0 /100ml 0/100 ml Median · Spandau

Chemical parameters (23)

Chemical parameters – Spandau
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Spandau
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Spandau
Arsenic 0,00034 mg/l 10 µg/l
3 %
Median · Spandau
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Spandau
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Spandau
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Spandau
Boron 0,044 mg/l 1 mg/l
4 %
Median · Spandau
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Spandau
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Spandau
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Spandau
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Spandau
Fluoride 0,14 mg/l 1.5 mg/l
9 %
Median · Spandau
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Spandau
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Spandau
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Spandau
Nitrate 1,09 mg/l 50 mg/l
2 %
Median · Spandau
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Spandau
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Spandau
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Spandau
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Spandau
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Spandau
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Spandau
Uranium 0,0002 mg/l 10 µg/l
2 %
Median · Spandau

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Spandau
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,0000012 mg/l Median · Spandau
Sum of PFAS 0,0000035 mg/l Median · Spandau

Indicator parameters (17)

Indicator parameters – Spandau
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Spandau
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Spandau
Chloride 47 mg/l 250 mg/l
19 %
Median · Spandau
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Spandau
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Spandau
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Median · Spandau
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Spandau
Colour 0,2 1/m 0.5 m⁻¹ Median · Spandau
Conductivity (25 °C) 650 µS/cm 2,790 µS/cm Median · Spandau
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Spandau
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Spandau
pH 7,5 - 6,5–9,5 Median · Spandau
Sodium 30 mg/l 200 mg/l
15 %
Median · Spandau
Sulphate 66 mg/l 250 mg/l
26 %
Median · Spandau
Temperature 12,6 °C Median · Spandau
Total organic carbon (TOC) 4,9 mg/l ohne anormale Veränderung Median · Spandau
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Spandau

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Spandau
Parameter Value Parametric value Share of the parametric value Reference
Calcium 95 mg/l Median · Spandau
Carbonate hardness 10,9 °dH Median · Spandau
Hardness range (WRMG) hart / hard - Median · Spandau
Magnesium 8,2 mg/l Median · Spandau
Oxygen 8,7 mg/l Median · Spandau
Potassium 3,7 mg/l Median · Spandau
Total hardness 15,1 °dH Median · Spandau

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
15.3 °dH
Hardness range hart / hard
Key values Stolpe
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,0000032 mg/l Median · Stolpe
Nitrate 3,14 mg/l 50 mg/l
6 %
Median · Stolpe
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Stolpe
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Stolpe
Sulphate 62 mg/l 250 mg/l
25 %
Median · Stolpe
Sodium 28 mg/l 200 mg/l
14 %
Median · Stolpe

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Stolpe
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Stolpe
Intestinal enterococci 0 /100ml 0/100 ml Median · Stolpe

Chemical parameters (23)

Chemical parameters – Stolpe
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Stolpe
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Stolpe
Arsenic 0,00039 mg/l 10 µg/l
4 %
Median · Stolpe
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Stolpe
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Stolpe
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Stolpe
Boron 0,062 mg/l 1 mg/l
6 %
Median · Stolpe
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Stolpe
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Stolpe
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Stolpe
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Stolpe
Fluoride 0,19 mg/l 1.5 mg/l
13 %
Median · Stolpe
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Stolpe
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Stolpe
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Stolpe
Nitrate 3,14 mg/l 50 mg/l
6 %
Median · Stolpe
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Stolpe
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Stolpe
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Stolpe
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Stolpe
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Stolpe
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Stolpe
Uranium 0,0001 mg/l 10 µg/l
1 %
Median · Stolpe

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Stolpe
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,0000013 mg/l Median · Stolpe
Sum of PFAS 0,0000032 mg/l Median · Stolpe

Indicator parameters (17)

Indicator parameters – Stolpe
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Stolpe
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Stolpe
Chloride 42 mg/l 250 mg/l
17 %
Median · Stolpe
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Stolpe
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Stolpe
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Median · Stolpe
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Stolpe
Colour 0,4 1/m 0.5 m⁻¹ Median · Stolpe
Conductivity (25 °C) 650 µS/cm 2,790 µS/cm Median · Stolpe
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Stolpe
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Stolpe
pH 7,5 - 6,5–9,5 Median · Stolpe
Sodium 28 mg/l 200 mg/l
14 %
Median · Stolpe
Sulphate 62 mg/l 250 mg/l
25 %
Median · Stolpe
Temperature 12,0 °C Median · Stolpe
Total organic carbon (TOC) 5,5 mg/l ohne anormale Veränderung Median · Stolpe
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Stolpe

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Stolpe
Parameter Value Parametric value Share of the parametric value Reference
Calcium 93 mg/l Median · Stolpe
Carbonate hardness 11,5 °dH Median · Stolpe
Hardness range (WRMG) hart / hard - Median · Stolpe
Magnesium 10,0 mg/l Median · Stolpe
Oxygen 9,2 mg/l Median · Stolpe
Potassium 3,8 mg/l Median · Stolpe
Total hardness 15,3 °dH Median · Stolpe

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
15.3 °dH
Hardness range hart / hard
Key values Tegel
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,000034 mg/l Median · Tegel
Nitrate 2,92 mg/l 50 mg/l
6 %
Median · Tegel
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Tegel
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Tegel
Sulphate 89 mg/l 250 mg/l
36 %
Median · Tegel
Sodium 37 mg/l 200 mg/l
18 %
Median · Tegel

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Tegel
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Tegel
Intestinal enterococci 0 /100ml 0/100 ml Median · Tegel

Chemical parameters (23)

Chemical parameters – Tegel
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Tegel
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Tegel
Arsenic 0,0020 mg/l 10 µg/l
20 %
Median · Tegel
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Tegel
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Tegel
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Tegel
Boron 0,077 mg/l 1 mg/l
8 %
Median · Tegel
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Tegel
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Tegel
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Tegel
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Tegel
Fluoride 0,21 mg/l 1.5 mg/l
14 %
Median · Tegel
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Tegel
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Tegel
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Tegel
Nitrate 2,92 mg/l 50 mg/l
6 %
Median · Tegel
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Tegel
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Tegel
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Tegel
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Tegel
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Tegel
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Tegel
Uranium 0,0004 mg/l 10 µg/l
4 %
Median · Tegel

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Tegel
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,000018 mg/l Median · Tegel
Sum of PFAS 0,000034 mg/l Median · Tegel

Indicator parameters (17)

Indicator parameters – Tegel
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Tegel
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Tegel
Chloride 52 mg/l 250 mg/l
21 %
Median · Tegel
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Tegel
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Tegel
Colony count 22 °C 0 KBE/ml ohne anormale Veränderung Median · Tegel
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Tegel
Colour 0,3 1/m 0.5 m⁻¹ Median · Tegel
Conductivity (25 °C) 700 µS/cm 2,790 µS/cm Median · Tegel
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Tegel
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Tegel
pH 7,5 - 6,5–9,5 Median · Tegel
Sodium 37 mg/l 200 mg/l
18 %
Median · Tegel
Sulphate 89 mg/l 250 mg/l
36 %
Median · Tegel
Temperature 12,9 °C Median · Tegel
Total organic carbon (TOC) 4,7 mg/l ohne anormale Veränderung Median · Tegel
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Tegel

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Tegel
Parameter Value Parametric value Share of the parametric value Reference
Calcium 94 mg/l Median · Tegel
Carbonate hardness 10,5 °dH Median · Tegel
Hardness range (WRMG) hart / hard - Median · Tegel
Magnesium 9,8 mg/l Median · Tegel
Oxygen 7,8 mg/l Median · Tegel
Potassium 7,6 mg/l Median · Tegel
Total hardness 15,3 °dH Median · Tegel

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
22.4 °dH
Hardness range hart / hard
Key values Tiefwerder
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,000016 mg/l Median · Tiefwerder
Nitrate 4,07 mg/l 50 mg/l
8 %
Median · Tiefwerder
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Tiefwerder
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Tiefwerder
Sulphate 152 mg/l 250 mg/l
61 %
Median · Tiefwerder
Sodium 66 mg/l 200 mg/l
33 %
Median · Tiefwerder

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Tiefwerder
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Tiefwerder
Intestinal enterococci 0 /100ml 0/100 ml Median · Tiefwerder

Chemical parameters (23)

Chemical parameters – Tiefwerder
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Tiefwerder
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Tiefwerder
Arsenic <0,00030 mg/l
below limit of quantification
10 µg/l
< 3 % *
Median · Tiefwerder
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Tiefwerder
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Tiefwerder
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Tiefwerder
Boron 0,043 mg/l 1 mg/l
4 %
Median · Tiefwerder
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Tiefwerder
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Tiefwerder
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Tiefwerder
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Tiefwerder
Fluoride 0,14 mg/l 1.5 mg/l
9 %
Median · Tiefwerder
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Tiefwerder
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Tiefwerder
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Tiefwerder
Nitrate 4,07 mg/l 50 mg/l
8 %
Median · Tiefwerder
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Tiefwerder
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Tiefwerder
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Tiefwerder
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Tiefwerder
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Tiefwerder
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Tiefwerder
Uranium <0,00005 mg/l
below limit of quantification
10 µg/l
< 0.5 % *
Median · Tiefwerder

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Tiefwerder
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,0000076 mg/l Median · Tiefwerder
Sum of PFAS 0,000016 mg/l Median · Tiefwerder

Indicator parameters (17)

Indicator parameters – Tiefwerder
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Tiefwerder
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Tiefwerder
Chloride 91 mg/l 250 mg/l
36 %
Median · Tiefwerder
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Tiefwerder
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Tiefwerder
Colony count 22 °C 1 KBE/ml ohne anormale Veränderung Median · Tiefwerder
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Tiefwerder
Colour <0,2 1/m
below limit of quantification
0.5 m⁻¹ Median · Tiefwerder
Conductivity (25 °C) 1.040 µS/cm 2,790 µS/cm Median · Tiefwerder
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Tiefwerder
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Tiefwerder
pH 7,4 - 6,5–9,5 Median · Tiefwerder
Sodium 66 mg/l 200 mg/l
33 %
Median · Tiefwerder
Sulphate 152 mg/l 250 mg/l
61 %
Median · Tiefwerder
Temperature 12,3 °C Median · Tiefwerder
Total organic carbon (TOC) 3,7 mg/l ohne anormale Veränderung Median · Tiefwerder
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Tiefwerder

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Tiefwerder
Parameter Value Parametric value Share of the parametric value Reference
Calcium 143 mg/l Median · Tiefwerder
Carbonate hardness 14,0 °dH Median · Tiefwerder
Hardness range (WRMG) hart / hard - Median · Tiefwerder
Magnesium 11,3 mg/l Median · Tiefwerder
Oxygen 6,4 mg/l Median · Tiefwerder
Potassium 4,4 mg/l Median · Tiefwerder
Total hardness 22,4 °dH Median · Tiefwerder

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
23.3 °dH
Hardness range hart / hard
Key values Wuhlheide
Parameter Value Parametric value Share of the parametric value Reference
Sum of PFAS 0,000014 mg/l Median · Wuhlheide
Nitrate 3,90 mg/l 50 mg/l
8 %
Median · Wuhlheide
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Wuhlheide
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Wuhlheide
Sulphate 163 mg/l 250 mg/l
65 %
Median · Wuhlheide
Sodium 32 mg/l 200 mg/l
16 %
Median · Wuhlheide

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (51 — most recent value per parameter)

Microbiology (2)

Microbiology – Wuhlheide
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 MPN/100ml 0/100 ml Median · Wuhlheide
Intestinal enterococci 0 /100ml 0/100 ml Median · Wuhlheide

Chemical parameters (23)

Chemical parameters – Wuhlheide
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Wuhlheide
Antimony <0,00050 mg/l
below limit of quantification
5 µg/l
< 10 % *
Median · Wuhlheide
Arsenic <0,00030 mg/l
below limit of quantification
10 µg/l
< 3 % *
Median · Wuhlheide
Benzene <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Wuhlheide
Benzo(a)pyrene <0,0000050 mg/l
below limit of quantification
10 ng/l
< 50 % *
Median · Wuhlheide
Bisphenol A <0,000025 mg/l
below limit of quantification
2.5 µg/l
< 1 % *
Median · Wuhlheide
Boron 0,11 mg/l 1 mg/l
11 %
Median · Wuhlheide
Cadmium <0,00050 mg/l
below limit of quantification
3 µg/l
< 17 % *
Median · Wuhlheide
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Median · Wuhlheide
Copper <0,0050 mg/l
below limit of quantification
2 mg/l
< 0.3 % *
Median · Wuhlheide
Cyanide <0,0030 mg/l
below limit of quantification
50 µg/l
< 6 % *
Median · Wuhlheide
Fluoride 0,29 mg/l 1.5 mg/l
19 %
Median · Wuhlheide
Lead <0,00050 mg/l
below limit of quantification
10 µg/l
< 5 % *
Median · Wuhlheide
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Median · Wuhlheide
Nickel <0,0030 mg/l
below limit of quantification
20 µg/l
< 15 % *
Median · Wuhlheide
Nitrate 3,90 mg/l 50 mg/l
8 %
Median · Wuhlheide
Nitrite <0,03 mg/l
below limit of quantification
0.5 mg/l
< 6 % *
Median · Wuhlheide
Pesticides — Total -/- mg/l
not detectable
0.5 µg/l Median · Wuhlheide
Polycyclic aromatic hydrocarbons -/- mg/l
not detectable
0.1 µg/l Median · Wuhlheide
Selenium <0,0010 mg/l
below limit of quantification
10 µg/l
< 10 % *
Median · Wuhlheide
Tetrachloroethene and Trichloroethene (sum) -/- mg/l
not detectable
10 µg/l Median · Wuhlheide
Trihalomethanes — Total -/- mg/l
not detectable
50 µg/l Median · Wuhlheide
Uranium 0,0003 mg/l 10 µg/l
3 %
Median · Wuhlheide

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

PFAS (2)

PFAS – Wuhlheide
Parameter Value Parametric value Share of the parametric value Reference
Sum of 4 PFAS 0,0000041 mg/l Median · Wuhlheide
Sum of PFAS 0,000014 mg/l Median · Wuhlheide

Indicator parameters (17)

Indicator parameters – Wuhlheide
Parameter Value Parametric value Share of the parametric value Reference
Aluminium <0,0100 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Median · Wuhlheide
Ammonium <0,05 mg/l
below limit of quantification
0.5 mg/l
< 10 % *
Median · Wuhlheide
Chloride 49 mg/l 250 mg/l
20 %
Median · Wuhlheide
Clostridium perfringens (including spores) 0 /100ml 0/100 ml Median · Wuhlheide
Coliform bacteria 0 MPN/100ml 0/100 ml Median · Wuhlheide
Colony count 22 °C 1 KBE/ml ohne anormale Veränderung Median · Wuhlheide
Colony count 36 °C 0 KBE/ml ohne anormale Veränderung Median · Wuhlheide
Colour 0,3 1/m 0.5 m⁻¹ Median · Wuhlheide
Conductivity (25 °C) 920 µS/cm 2,790 µS/cm Median · Wuhlheide
Iron <0,030 mg/l
below limit of quantification
0.2 mg/l
< 15 % *
Median · Wuhlheide
Manganese <0,005 mg/l
below limit of quantification
50 µg/l
< 10 % *
Median · Wuhlheide
pH 7,4 - 6,5–9,5 Median · Wuhlheide
Sodium 32 mg/l 200 mg/l
16 %
Median · Wuhlheide
Sulphate 163 mg/l 250 mg/l
65 %
Median · Wuhlheide
Temperature 11,8 °C Median · Wuhlheide
Total organic carbon (TOC) 4,4 mg/l ohne anormale Veränderung Median · Wuhlheide
Turbidity <0,2 NTU
below limit of quantification
1 NTU Median · Wuhlheide

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (7)

Further parameters – Wuhlheide
Parameter Value Parametric value Share of the parametric value Reference
Calcium 141 mg/l Median · Wuhlheide
Carbonate hardness 13,7 °dH Median · Wuhlheide
Hardness range (WRMG) hart / hard - Median · Wuhlheide
Magnesium 15,3 mg/l Median · Wuhlheide
Oxygen 10,0 mg/l Median · Wuhlheide
Potassium 8,1 mg/l Median · Wuhlheide
Total hardness 23,3 °dH Median · Wuhlheide

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.bwb.de/de/assets/downloads/analysewerte-wasserwerke.pdf · Jahresmedianwerte 2025 · retrieved on 25/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

No core values are available for this zone yet.

Show all recorded parameters (1 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Wasserwerk Stolpe
Parameter Value Parametric value Share of the parametric value Reference
pH 7,5 6,5–9,5 Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wassernord.de/trinkwasser/faqs · retrieved on 25/07/2026

Frequent questions about postcode 16567

How hard is the water in Postcode 16567?
Niederbarnimer Wasser- und Abwasserzweckverband (NWA) publishes the hardness range 13,1 for the supply zone Prenden. The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Publication by the water supplier, retrieved on 11/07/2026.
Who supplies the drinking water in Postcode 16567?
Niederbarnimer Wasser- und Abwasserzweckverband (NWA). The values shown here come from the supply zone Prenden and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.