Skip to content
maunawai.info

Drinking water in 09579

For this postcode the responsible water supplier publishes several supply zones. Which of them serves an individual address is not published — below are the values of the zone with the most documented parameters, the remaining 11 underneath. The water supplier publishes 104 further local networks that cannot be clearly assigned to this postcode — they are listed on the water supplier page.

How to read the share of the parametric value

12 % Share of the parametric value. The proportion of the permitted maximum that the measured value uses — here 12 %, so just over an eighth.
< 10 % * Below the limit of quantification. The substance was not detectable. The mark shows where the detection limit lies relative to the parametric value — the actual share of the parametric value is below that.

Several samples per year: for chemical parameters the mean value is given, for microbiological ones the highest measured value. There the parametric value is zero — a single finding would disappear in the average, and it is precisely that finding which is the information. Which reference applies is stated in the last column of the table.

Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289)

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
5.1 °dH
Hardness range soft
Key values Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289)
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 11 mg/l 50 mg/l
22 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Sulphate 30 mg/l 250 mg/l
12 %
Single value
Sodium 11,1 mg/l 200 mg/l
6 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (52 — most recent value per parameter)

Microbiology (2)

Microbiology – Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289)
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Intestinal enterococci 0 Anzahl/100ml 0/100 ml Single value

Chemical parameters (28)

Chemical parameters – Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289)
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0009 mg/l
below limit of quantification
3 µg/l
< 30 % *
Single value
Antimony <0,0010 mg/l
below limit of quantification
5 µg/l
< 20 % *
Single value
Arsenic <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Benzene <0,00050 mg/l
below limit of quantification
1 µg/l
< 50 % *
Single value
Benzo(a)pyrene <0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Boron 0,014 mg/l 1 mg/l
1 %
Single value
Bromate <0,0025 mg/l
below limit of quantification
10 µg/l
< 25 % *
Single value
Bromodichloromethane 0,0052 mg/l Single value
Cadmium <0,0001 mg/l
below limit of quantification
3 µg/l
< 3 % *
Single value
Chlorate 0,029 mg/l 70 µg/l
41 %
Single value
Chlorite 0,16 mg/l 0.2 mg/l
80 %
Single value
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper 0,0024 mg/l 2 mg/l
0.1 %
Single value
Cyanide <0,01 mg/l
below limit of quantification
50 µg/l
< 20 % *
Single value
Dibromochloromethane 0,0027 mg/l Single value
Fluoride 0,1 mg/l 1.5 mg/l
7 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Nickel 0,001 mg/l 20 µg/l
5 %
Single value
Nitrate 11 mg/l 50 mg/l
22 %
Single value
Nitrite <0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value
Selenium 0,001 mg/l 10 µg/l
10 %
Single value
Tetrachloroethene <0,0003 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) <0,0003 mg/l
below limit of quantification
Single value
Trichloroethene <0,0003 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) 0,0066 mg/l Single value
Trihalomethanes — Total 0,015 mg/l 50 µg/l
30 %
Single value
Uranium <0,00010 mg/l
below limit of quantification
10 µg/l
< 1 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (18)

Indicator parameters – Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289)
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,013 mg/l 0.2 mg/l
6 %
Single value
Ammonium <0,02 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value
Calcite dissolution capacity <5,00 mg/l
below limit of quantification
5 mg/l CaCO3 Single value
Chloride 27,9 mg/l 250 mg/l
11 %
Single value
Clostridium perfringens (including spores) 0 Anzahl/100ml 0/100 ml Single value
Coliform bacteria 0 Anzahl/100ml 0/100 ml Single value
Colony count 22 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colour <0,1 1/m
below limit of quantification
0.5 m⁻¹ Single value
Iron <0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Manganese 0,009 mg/l 50 µg/l
18 %
Single value
Odour ohne annehmbar u. ohne anormale Veränderung für den Verbraucher annehmbar Single value
pH 7,9 - 6,5–9,5 Single value
Sodium 11,1 mg/l 200 mg/l
6 %
Single value
Sulphate 30 mg/l 250 mg/l
12 %
Single value
Taste ohne annehmbar u. ohne anormale Veränderung für den Verbraucher annehmbar Single value
Total organic carbon (TOC) 1,5 mg/l ohne anormale Veränderung Single value
Turbidity 0,19 FNU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289)
Parameter Value Parametric value Share of the parametric value Reference
Calcium 26,9 mg/l Single value
Magnesium 5,63 mg/l Single value
Potassium 2 mg/l Single value
Total hardness 5,1 °dH Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Show 11 more supply zones in this postcode

Annaberg-Buchholz OT Buchholz*, Annaberg-Buchholz OT Cunersdorf, Annaberg-Buchholz OT Frohnau, Schlettau OT Dörfel, Sehmatal OT Sehma, Thermalbad Wiesenbad OT Neundorf

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
3.6 °dH
Hardness range soft
Key values Annaberg-Buchholz OT Buchholz*, Annaberg-Buchholz OT Cunersdorf, Annaberg-Buchholz OT Frohnau, Schlettau OT Dörfel, Sehmatal OT Sehma, Thermalbad Wiesenbad OT Neundorf
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 1,1 mg/l 50 mg/l
2 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Sulphate 15 mg/l 250 mg/l
6 %
Single value
Sodium 3,83 mg/l 200 mg/l
2 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (52 — most recent value per parameter)

Microbiology (2)

Microbiology – Annaberg-Buchholz OT Buchholz*, Annaberg-Buchholz OT Cunersdorf, Annaberg-Buchholz OT Frohnau, Schlettau OT Dörfel, Sehmatal OT Sehma, Thermalbad Wiesenbad OT Neundorf
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Intestinal enterococci 0 Anzahl/100ml 0/100 ml Single value

Chemical parameters (28)

Chemical parameters – Annaberg-Buchholz OT Buchholz*, Annaberg-Buchholz OT Cunersdorf, Annaberg-Buchholz OT Frohnau, Schlettau OT Dörfel, Sehmatal OT Sehma, Thermalbad Wiesenbad OT Neundorf
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0009 mg/l
below limit of quantification
3 µg/l
< 30 % *
Single value
Antimony <0,0010 mg/l
below limit of quantification
5 µg/l
< 20 % *
Single value
Arsenic <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Benzene <0,00050 mg/l
below limit of quantification
1 µg/l
< 50 % *
Single value
Benzo(a)pyrene <0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Boron 0,01 mg/l 1 mg/l
1 %
Single value
Bromate <0,0025 mg/l
below limit of quantification
10 µg/l
< 25 % *
Single value
Bromodichloromethane <0,0003 mg/l
below limit of quantification
Single value
Cadmium <0,0001 mg/l
below limit of quantification
3 µg/l
< 3 % *
Single value
Chlorate 0,028 mg/l 70 µg/l
40 %
Single value
Chlorite 0,14 mg/l 0.2 mg/l
70 %
Single value
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper 0,0039 mg/l 2 mg/l
0.2 %
Single value
Cyanide <0,01 mg/l
below limit of quantification
50 µg/l
< 20 % *
Single value
Dibromochloromethane <0,0003 mg/l
below limit of quantification
Single value
Fluoride 0,13 mg/l 1.5 mg/l
9 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Nickel <0,001 mg/l
below limit of quantification
20 µg/l
< 5 % *
Single value
Nitrate 1,1 mg/l 50 mg/l
2 %
Single value
Nitrite <0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value
Selenium <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Tetrachloroethene <0,0003 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) <0,0003 mg/l
below limit of quantification
Single value
Trichloroethene <0,0003 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) 0,00033 mg/l Single value
Trihalomethanes — Total 0,00033 mg/l 50 µg/l
0.7 %
Single value
Uranium <0,00010 mg/l
below limit of quantification
10 µg/l
< 1 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (18)

Indicator parameters – Annaberg-Buchholz OT Buchholz*, Annaberg-Buchholz OT Cunersdorf, Annaberg-Buchholz OT Frohnau, Schlettau OT Dörfel, Sehmatal OT Sehma, Thermalbad Wiesenbad OT Neundorf
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,019 mg/l 0.2 mg/l
10 %
Single value
Ammonium <0,020 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value
Calcite dissolution capacity <5,00 mg/l
below limit of quantification
5 mg/l CaCO3 Single value
Chloride 8,8 mg/l 250 mg/l
4 %
Single value
Clostridium perfringens (including spores) 0 Anzahl/100ml 0/100 ml Single value
Coliform bacteria 0 Anzahl/100ml 0/100 ml Single value
Colony count 22 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colour <0,1 1/m
below limit of quantification
0.5 m⁻¹ Single value
Iron <0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Manganese <0,001 mg/l
below limit of quantification
50 µg/l
< 2 % *
Single value
Odour ohne annehmbar u. ohne anormale Veränderung für den Verbraucher annehmbar Single value
pH 8,3 - 6,5–9,5 Single value
Sodium 3,83 mg/l 200 mg/l
2 %
Single value
Sulphate 15 mg/l 250 mg/l
6 %
Single value
Taste ohne annehmbar u. ohne anormale Veränderung für den Verbraucher annehmbar Single value
Total organic carbon (TOC) 0,83 mg/l ohne anormale Veränderung Single value
Turbidity 0,19 FNU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Annaberg-Buchholz OT Buchholz*, Annaberg-Buchholz OT Cunersdorf, Annaberg-Buchholz OT Frohnau, Schlettau OT Dörfel, Sehmatal OT Sehma, Thermalbad Wiesenbad OT Neundorf
Parameter Value Parametric value Share of the parametric value Reference
Calcium 20,7 mg/l Single value
Magnesium 2,87 mg/l Single value
Potassium 1 mg/l Single value
Total hardness 3,6 °dH Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Jöhstadt OT Oberschmiedeberg; Mildenau OT Arnsfeld*; Mildenau OT Mittelschmiedeberg, Oberschaar (TWU-Nr. A007)

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
4.2 °dH
Hardness range soft
Key values Jöhstadt OT Oberschmiedeberg; Mildenau OT Arnsfeld*; Mildenau OT Mittelschmiedeberg, Oberschaar (TWU-Nr. A007)
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 27 mg/l 50 mg/l
54 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Sulphate 25 mg/l 250 mg/l
10 %
Single value
Sodium 6,63 mg/l 200 mg/l
3 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (52 — most recent value per parameter)

Microbiology (2)

Microbiology – Jöhstadt OT Oberschmiedeberg; Mildenau OT Arnsfeld*; Mildenau OT Mittelschmiedeberg, Oberschaar (TWU-Nr. A007)
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Intestinal enterococci 0 Anzahl/100ml 0/100 ml Single value

Chemical parameters (28)

Chemical parameters – Jöhstadt OT Oberschmiedeberg; Mildenau OT Arnsfeld*; Mildenau OT Mittelschmiedeberg, Oberschaar (TWU-Nr. A007)
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0009 mg/l
below limit of quantification
3 µg/l
< 30 % *
Single value
Antimony <0,0010 mg/l
below limit of quantification
5 µg/l
< 20 % *
Single value
Arsenic <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Benzene <0,00050 mg/l
below limit of quantification
1 µg/l
< 50 % *
Single value
Benzo(a)pyrene <0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Boron <0,010 mg/l
below limit of quantification
1 mg/l
< 1 % *
Single value
Bromate <0,0025 mg/l
below limit of quantification
10 µg/l
< 25 % *
Single value
Bromodichloromethane 0,0015 mg/l Single value
Cadmium 0,0002 mg/l 3 µg/l
7 %
Single value
Chlorate 0,013 mg/l 70 µg/l
19 %
Single value
Chlorite <0,05 mg/l
below limit of quantification
0.2 mg/l
< 25 % *
Single value
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper 0,0021 mg/l 2 mg/l
0.1 %
Single value
Cyanide <0,01 mg/l
below limit of quantification
50 µg/l
< 20 % *
Single value
Dibromochloromethane 0,0021 mg/l Single value
Fluoride 0,17 mg/l 1.5 mg/l
11 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Nickel 0,001 mg/l 20 µg/l
5 %
Single value
Nitrate 27 mg/l 50 mg/l
54 %
Single value
Nitrite <0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value
Selenium <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Tetrachloroethene <0,0003 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) 0,0009 mg/l Single value
Trichloroethene <0,0003 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) <0,0003 mg/l
below limit of quantification
Single value
Trihalomethanes — Total 0,0044 mg/l 50 µg/l
9 %
Single value
Uranium 0,00014 mg/l 10 µg/l
1 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (18)

Indicator parameters – Jöhstadt OT Oberschmiedeberg; Mildenau OT Arnsfeld*; Mildenau OT Mittelschmiedeberg, Oberschaar (TWU-Nr. A007)
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,017 mg/l 0.2 mg/l
9 %
Single value
Ammonium <0,020 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value
Calcite dissolution capacity <5,00 mg/l
below limit of quantification
5 mg/l CaCO3 Single value
Chloride 4,4 mg/l 250 mg/l
2 %
Single value
Clostridium perfringens (including spores) 0 Anzahl/100ml 0/100 ml Single value
Coliform bacteria 0 Anzahl/100ml 0/100 ml Single value
Colony count 22 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colour <0,1 1/m
below limit of quantification
0.5 m⁻¹ Single value
Iron <0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Manganese <0,001 mg/l
below limit of quantification
50 µg/l
< 2 % *
Single value
Odour ohne für den Verbraucher annehmbar Single value
pH 8,3 - 6,5–9,5 Single value
Sodium 6,63 mg/l 200 mg/l
3 %
Single value
Sulphate 25 mg/l 250 mg/l
10 %
Single value
Taste ohne für den Verbraucher annehmbar Single value
Total organic carbon (TOC) 0,5 mg/l ohne anormale Veränderung Single value
Turbidity 0,14 FNU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – Jöhstadt OT Oberschmiedeberg; Mildenau OT Arnsfeld*; Mildenau OT Mittelschmiedeberg, Oberschaar (TWU-Nr. A007)
Parameter Value Parametric value Share of the parametric value Reference
Calcium 23,2 mg/l Single value
Magnesium 4,08 mg/l Single value
Potassium 1,3 mg/l Single value
Total hardness 4,2 °dH Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

TWU-Nr. A028: Annaberg-Buchholz OT Annaberg u. OT Kleinrückerswald; Annaberg-Buchholz OT Geyersdorf u. Kleinrückerswalde; Thermalbad Wiesenbad; Thermalbad Wiesenbad OT Wiesa

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

No date is given for these values. The water supplier publishes the analysis without a sampling date and without a report date. When the water was examined is not apparent from the source — we do not add a date and we do not estimate one. What is stated is therefore only when we retrieved the document.

Water hardness
4.1 °dH
Hardness range soft
Key values TWU-Nr. A028: Annaberg-Buchholz OT Annaberg u. OT Kleinrückerswald; Annaberg-Buchholz OT Geyersdorf u. Kleinrückerswalde; Thermalbad Wiesenbad; Thermalbad Wiesenbad OT Wiesa
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 3,7 mg/l 50 mg/l
7 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Sulphate 23 mg/l 250 mg/l
9 %
Single value
Sodium 8,02 mg/l 200 mg/l
4 %
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Show all recorded parameters (52 — most recent value per parameter)

Microbiology (2)

Microbiology – TWU-Nr. A028: Annaberg-Buchholz OT Annaberg u. OT Kleinrückerswald; Annaberg-Buchholz OT Geyersdorf u. Kleinrückerswalde; Thermalbad Wiesenbad; Thermalbad Wiesenbad OT Wiesa
Parameter Value Parametric value Share of the parametric value Reference
Escherichia coli (E. coli) 0 Anzahl/100ml 0/100 ml Single value
Intestinal enterococci 0 Anzahl/100ml 0/100 ml Single value

Chemical parameters (28)

Chemical parameters – TWU-Nr. A028: Annaberg-Buchholz OT Annaberg u. OT Kleinrückerswald; Annaberg-Buchholz OT Geyersdorf u. Kleinrückerswalde; Thermalbad Wiesenbad; Thermalbad Wiesenbad OT Wiesa
Parameter Value Parametric value Share of the parametric value Reference
1,2-dichloroethane <0,0009 mg/l
below limit of quantification
3 µg/l
< 30 % *
Single value
Antimony <0,0010 mg/l
below limit of quantification
5 µg/l
< 20 % *
Single value
Arsenic <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Benzene <0,00050 mg/l
below limit of quantification
1 µg/l
< 50 % *
Single value
Benzo(a)pyrene <0,000003 mg/l
below limit of quantification
10 ng/l
< 30 % *
Single value
Boron <0,01 mg/l
below limit of quantification
1 mg/l
< 1 % *
Single value
Bromate <0,0025 mg/l
below limit of quantification
10 µg/l
< 25 % *
Single value
Bromodichloromethane 0,0026 mg/l Single value
Cadmium 0,0003 mg/l 3 µg/l
10 %
Single value
Chlorate 0,018 mg/l 70 µg/l
26 %
Single value
Chlorite 0,058 mg/l 0.2 mg/l
29 %
Single value
Chromium <0,00050 mg/l
below limit of quantification
25 µg/l
< 2 % *
Single value
Copper <0,001 mg/l
below limit of quantification
2 mg/l
< < 0.1 % *
Single value
Cyanide <0,01 mg/l
below limit of quantification
50 µg/l
< 20 % *
Single value
Dibromochloromethane 0,00066 mg/l Single value
Fluoride 0,16 mg/l 1.5 mg/l
11 %
Single value
Lead <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Mercury <0,00010 mg/l
below limit of quantification
1 µg/l
< 10 % *
Single value
Nickel 0,003 mg/l 20 µg/l
15 %
Single value
Nitrate 3,7 mg/l 50 mg/l
7 %
Single value
Nitrite <0,010 mg/l
below limit of quantification
0.5 mg/l
< 2 % *
Single value
Selenium <0,001 mg/l
below limit of quantification
10 µg/l
< 10 % *
Single value
Tetrachloroethene <0,0003 mg/l
below limit of quantification
Single value
Tribromomethane (bromoform) <0,0003 mg/l
below limit of quantification
Single value
Trichloroethene <0,0003 mg/l
below limit of quantification
Single value
Trichloromethane (chloroform) 0,0068 mg/l Single value
Trihalomethanes — Total 0,01 mg/l 50 µg/l
20 %
Single value
Uranium <0,0001 mg/l
below limit of quantification
10 µg/l
< 1 % *
Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Indicator parameters (18)

Indicator parameters – TWU-Nr. A028: Annaberg-Buchholz OT Annaberg u. OT Kleinrückerswald; Annaberg-Buchholz OT Geyersdorf u. Kleinrückerswalde; Thermalbad Wiesenbad; Thermalbad Wiesenbad OT Wiesa
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0,057 mg/l 0.2 mg/l
28 %
Single value
Ammonium <0,020 mg/l
below limit of quantification
0.5 mg/l
< 4 % *
Single value
Calcite dissolution capacity <5,00 mg/l
below limit of quantification
5 mg/l CaCO3 Single value
Chloride 13,9 mg/l 250 mg/l
6 %
Single value
Clostridium perfringens (including spores) 0 Anzahl/100ml 0/100 ml Single value
Coliform bacteria 0 Anzahl/100ml 0/100 ml Single value
Colony count 22 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colony count 36 °C 0 Anzahl/ml ohne anormale Veränderung Single value
Colour <0,1 1/m
below limit of quantification
0.5 m⁻¹ Single value
Iron <0,01 mg/l
below limit of quantification
0.2 mg/l
< 5 % *
Single value
Manganese <0,001 mg/l
below limit of quantification
50 µg/l
< 2 % *
Single value
Odour ohne annehmbar u. ohne anormale für den Verbraucher annehmbar Single value
pH 8,1 - 6,5–9,5 Single value
Sodium 8,02 mg/l 200 mg/l
4 %
Single value
Sulphate 23 mg/l 250 mg/l
9 %
Single value
Taste ohne Veränderung für den Verbraucher annehmbar Single value
Total organic carbon (TOC) 1,4 mg/l ohne anormale Veränderung Single value
Turbidity 0,13 FNU 1 NTU Single value

* Value below the limit of quantification: the actual share of the parametric value is not known; it lies somewhere below the stated upper bound. The marker shows where the limit of quantification of the measurement lies relative to the parametric value.

Further parameters (4)

Further parameters – TWU-Nr. A028: Annaberg-Buchholz OT Annaberg u. OT Kleinrückerswald; Annaberg-Buchholz OT Geyersdorf u. Kleinrückerswalde; Thermalbad Wiesenbad; Thermalbad Wiesenbad OT Wiesa
Parameter Value Parametric value Share of the parametric value Reference
Calcium 23,7 mg/l Single value
Magnesium 3,5 mg/l Single value
Potassium 1,3 mg/l Single value
Total hardness 4,1 °dH Single value

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

WW EINSIEDEL (Sachsen, WSZ 1140)

WW EINSIEDEL (Sachsen)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

These values are more than a year old. The most recent analysis the water supplier has published for this zone dates from 31/12/2020. We have no newer values — which is why we show the latest available ones rather than none at all. They say nothing about how the water has changed since then.

Water hardness
5.7 °dH
Hardness range soft
Key values WW EINSIEDEL (Sachsen, WSZ 1140)
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 17.1 mg/l 50 mg/l
34 %
Mean
Sulphate 33 mg/l 250 mg/l
13 %
Mean
Show all recorded parameters (8 — most recent value per parameter)

Chemical parameters (2)

Chemical parameters – WW EINSIEDEL (Sachsen, WSZ 1140)
Parameter Value Parametric value Share of the parametric value Reference
Nitrate 17.1 mg/l 50 mg/l
34 %
Mean
Uranium 0.0001 mg/l 10 µg/l
1 %
Mean

Indicator parameters (5)

Indicator parameters – WW EINSIEDEL (Sachsen, WSZ 1140)
Parameter Value Parametric value Share of the parametric value Reference
Aluminium 0.03 mg/l 0.2 mg/l
15 %
Mean
Iron 0.03 mg/l 0.2 mg/l
15 %
Mean
Manganese 0.018 mg/l 50 µg/l
36 %
Mean
pH 8.0 - 6,5–9,5 Mean
Sulphate 33 mg/l 250 mg/l
13 %
Mean

Further parameters (1)

Further parameters – WW EINSIEDEL (Sachsen, WSZ 1140)
Parameter Value Parametric value Share of the parametric value Reference
Total hardness 5.7 °dH Mean

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Amtsberg OT Schlösschen

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
5.5 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Amtsberg OT Schlösschen
Parameter Value Parametric value Share of the parametric value Reference
pH 7,9 6,5–9,5 Single value · Amtsberg OT Schlösschen

Further parameters (2)

Further parameters – Amtsberg OT Schlösschen
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · Amtsberg OT Schlösschen
Total hardness 0,98 mmol/l Single value · Amtsberg OT Schlösschen

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserversorgung-etw.de/fileadmin/user_upload/TW/Analysedaten_01.pdf · 10/2025 · Daten 2024/2025 (Durchschnittswerte - gerundet) · retrieved on 11/07/2026

Amtsberg OT Schlösschen / Wilischthal

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
5.5 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Amtsberg OT Schlösschen / Wilischthal
Parameter Value Parametric value Share of the parametric value Reference
pH 7,9 6,5–9,5 Single value · Amtsberg OT Schlösschen / Wilischthal

Further parameters (2)

Further parameters – Amtsberg OT Schlösschen / Wilischthal
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · Amtsberg OT Schlösschen / Wilischthal
Total hardness 0,98 mmol/l Single value · Amtsberg OT Schlösschen / Wilischthal

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserversorgung-etw.de/fileadmin/user_upload/TW/Analysedaten_01.pdf · 10/2025 · Daten 2024/2025 (Durchschnittswerte - gerundet) · retrieved on 11/07/2026

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
0,98-1,65 mmol/l
Hardness range weich-mittel

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Amtsberg OT Weißbach
Parameter Value Parametric value Share of the parametric value Reference
pH 7,9-8,0 6,5–9,5 Single value · Amtsberg OT Weißbach

Further parameters (2)

Further parameters – Amtsberg OT Weißbach
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich-mittel Single value · Amtsberg OT Weißbach
Total hardness 0,98-1,65 mmol/l Single value · Amtsberg OT Weißbach

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserversorgung-etw.de/fileadmin/user_upload/TW/Analysedaten_01.pdf · 10/2025 · Daten 2024/2025 (Durchschnittswerte - gerundet) · retrieved on 11/07/2026

Amtsberg OT Weißbach / Wilischthal

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
3 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Amtsberg OT Weißbach / Wilischthal
Parameter Value Parametric value Share of the parametric value Reference
pH 8,3 6,5–9,5 Single value · Amtsberg OT Weißbach / Wilischthal

Further parameters (2)

Further parameters – Amtsberg OT Weißbach / Wilischthal
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · Amtsberg OT Weißbach / Wilischthal
Total hardness 0,54 mmol/l Single value · Amtsberg OT Weißbach / Wilischthal

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserversorgung-etw.de/fileadmin/user_upload/TW/Analysedaten_01.pdf · 10/2025 · Daten 2024/2025 (Durchschnittswerte - gerundet) · retrieved on 11/07/2026

Annaberg-Buchholz OT Buchholz

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
0,54-0,63 mmol/l
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Annaberg-Buchholz OT Buchholz
Parameter Value Parametric value Share of the parametric value Reference
pH 7,8-8,2 6,5–9,5 Single value · Annaberg-Buchholz OT Buchholz

Further parameters (2)

Further parameters – Annaberg-Buchholz OT Buchholz
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · Annaberg-Buchholz OT Buchholz
Total hardness 0,54-0,63 mmol/l Single value · Annaberg-Buchholz OT Buchholz

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserversorgung-etw.de/fileadmin/user_upload/TW/Analysedaten_01.pdf · 10/2025 · Daten 2024/2025 (Durchschnittswerte - gerundet) · retrieved on 11/07/2026

Annaberg-Buchholz OT Cunersdorf

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
3 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Annaberg-Buchholz OT Cunersdorf
Parameter Value Parametric value Share of the parametric value Reference
pH 8,2 6,5–9,5 Single value · Annaberg-Buchholz OT Cunersdorf

Further parameters (2)

Further parameters – Annaberg-Buchholz OT Cunersdorf
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · Annaberg-Buchholz OT Cunersdorf
Total hardness 0,54 mmol/l Single value · Annaberg-Buchholz OT Cunersdorf

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserversorgung-etw.de/fileadmin/user_upload/TW/Analysedaten_01.pdf · 10/2025 · Daten 2024/2025 (Durchschnittswerte - gerundet) · retrieved on 11/07/2026

Annaberg-Buchholz OT Frohnau

Erzgebirge Trinkwasser GmbH (ETW)

Assigned via the water supplier — the exact supply zone boundary within the postcode is not yet linked.

Water hardness
3 °dH
Hardness range weich

No core values are available for this zone yet.

Show all recorded parameters (3 — most recent value per parameter)

Indicator parameters (1)

Indicator parameters – Annaberg-Buchholz OT Frohnau
Parameter Value Parametric value Share of the parametric value Reference
pH 8,2 6,5–9,5 Single value · Annaberg-Buchholz OT Frohnau

Further parameters (2)

Further parameters – Annaberg-Buchholz OT Frohnau
Parameter Value Parametric value Share of the parametric value Reference
Hardness range (WRMG) weich Single value · Annaberg-Buchholz OT Frohnau
Total hardness 0,54 mmol/l Single value · Annaberg-Buchholz OT Frohnau

Values taken unchanged from the publications linked below — for each parameter the most recent recorded value. „—" in the parametric value column: no currently valid legal parametric value is stored in our database for this parameter; the parameter register with all parametric values is being expanded continuously.

Source: https://www.wasserversorgung-etw.de/fileadmin/user_upload/TW/Analysedaten_01.pdf · 10/2025 · Daten 2024/2025 (Durchschnittswerte - gerundet) · retrieved on 11/07/2026

Frequent questions about postcode 09579

How hard is the water in Postcode 09579?
Erzgebirge Trinkwasser GmbH (ETW) publishes a total hardness of 5.1 °dH for the supply zone Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289) (hardness range soft). The hardness range is a classification under the German Detergents and Cleaning Products Act (soft below 8,4 °dH, medium 8,4 to 14 °dH, hard above that) and not a quality verdict — it indicates how much calcium and magnesium is dissolved in the water. Basis: Mrz. 26, retrieved on 11/07/2026.
How much nitrate is in the drinking water in Postcode 09579?
Erzgebirge Trinkwasser GmbH (ETW) publishes a nitrate value of 11 mg/l for the supply zone Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289). The statutory parametric value is 50 mg/l; the measured value represents 22 % of the parametric value. Basis: Mrz. 26, retrieved on 11/07/2026.
Who supplies the drinking water in Postcode 09579?
Erzgebirge Trinkwasser GmbH (ETW). The values shown here come from the supply zone Amtsberg OT Schlößchen, Amtsberg OT Schlößchen / Wilischthal, Amtsberg OT Weißbach*, Börnichen, Gornau, Gornau OT Witzschdorf, Großolbersdorf OT Hohndorf, Grünhainichen OT Waldkirchen, Pockau-Lengefeld OT Görsdorf, Pockau-Lengefeld OT Lengefeld, Pockau-Lengefeld OT Lippersdorf, Pockau-Lengefeld OT Pockau*, Pockau-Lengefeld OT Reifland, Pockau-Lengefeld OT Wernsdorf, Pockau-Lengefeld OT Wünschendorf, Zschopau, Zschopau OT Krumhermersdorf*, Zschopau OT Wilischthal (TWU-Nr. A289) and apply to the water the supplier delivers. What happens between the building connection and the tap — in old lead pipes, for example — is not covered by these analyses; information on that is provided by owners, the health authority or an examination by an accredited laboratory.

General questions — how current the data is, limit of quantification, parametric values, who is behind this site — are answered under Questions & answers.